DOWNLOAD Sony HBD-E190 / HBD-E290 / HBD-E490 / HBD-E690 Service Manual ↓ Size: 8.04 MB | Pages: 97 in PDF or view online for FREE

There is a possibility that this mode cannot be correctly execut-
ed. Never use this mode.

13. Network (Network Test Diagnosis Screen: Ifconfi g)
Network menu for the wired ethernet.

Screen 1: Ifconfi g Test
Operation:
[

] Activate Ifconfi g (Display network setting)

[

,] 

Select ping test

[RETURN] Returns to the top menu of the service mode

Screen 2: Ping Test
Operation:
[

<

] Select 

Ifconfi g test

[RETURN]  Returns to the top menu of the service mode
(The details of a Ping test are “14. Network (Network Test Diagno-
sis Screen: Ping)”)

Screen 3: Ifconfi g Test Active
Display Ifconfi g command results.
Operation:
[

] Ifconfi g retry

[

,] Select 

Ping Test

[RETURN]  Returns to the top menu of the service mode

14. Network (Network Test Diagnosis Screen: Ping)
Ping test for the wired ethernet.

Screen 1: Ping Test
Operation:
[

<

] Select 

Ifconfi g test

[

m

] 

Ping execution preparation

[RETURN]  Returns to the top menu of the service mode

When “Ping to :>” is reversed, the [

] button is pressed and IP 

is inputted.
Operation:
[

] 

Finish to input

[RETURN]  Finish to input
[

<

] 

Finish to input and Select Ifconfi g Test

[0] to [9] 

Input Character sting ‘0-9’

[TIME] 

Input Character sting ‘.’

[CLEAR] Backspace

Screen 3: Ping Test Active
When [START] is reversed, the [

] button is pressed and execute 

ping.
Operation:
[

] 

Activate ping test

[

M

] 

The IP address of the ping point is set up

[RETURN]  Returns to the top menu of the service mode

15. System Information (System Information Display)
This screen displays system information.

Screen 1: Basic Information
Operation:
[

,

] 

Drive information (delta IOP of a drive is measured) 
and wireless device information (not used) displayed 
(go to Screen 2)

[RETURN]  Returns to the top menu of the service mode

Screen 2: Drive and Wireless Information Menu
Operation:
[

<

] 

Basic Information displayed (go to Screen 1)

[RETURN]  Returns to the top menu of the service mode

When delta IOP is measured, it becomes impossible to use the Ver-
sion Up function.

 Network

 Network

 Network

 Network

 Network

Contents List:
Main LSIname
Model
Destination
Sequence Number
MAC
IP
IFCON IFCON 

Version

Bootloader Bootloader 

Version

Host Main 

Host Main Version

MicroBE MicroBE 

Version

Host Sub 

Host Sub Version

Middleware Middleware 

Version

ADSP ADSP 

Version

ADSP Coeff 

ADSP Coeff Version

2nd DSP 

2nd DSP Version (not used)

IF Model
IF Dest
WLAN module Serial
WLAN module hw Version
WLAN module MAC Address
Drive Firm Revision
CD DIOP 

Delta IOP

DVD DIOP 

Delta IOP

BD DIOP 

Delta IOP

CD LD TIME 

LD Time

DVD LD TIME  LD Time
BD LD TIME 

LD Time

 

16. Drive
This menu is used to operate the drive using drive-related diagnos-
tic and tools.

Screen 1: Selecting items under *Drive
Operation:
[

<

]/[

,

]  Selects the category

[

m

]/[

] 

Activate the selected category

[RETURN]  Returns to the top menu of the service mode
[1]  Drive OP data Write
[2]  Servo Parameter Check Menu (Not used)
[3]  Servo Signal Check Menu (Not used)
[4]  S-Curve Check Menu (Not used)
[5]  Readability Check Menu (Not used)
[6]  OP Position Check Menu (Not used)
[7]  OP Check Menu (Not used)
[8]  Load Eject Aging (Not used)
[9]  Spindle Control Check Menu (Not used)
[10] FA Test Mode (Not used)

Screen 2: To start OP data Write
Operation:
[

] Starts

Screen 3: Show OP data Write result
Operation:
NG - USB is not fi nd
OK - OP data write

• Drive 

Test

For drive operating check. Service is only use Drive OP data write 
to rewrite OP data after change of new CPU.

 Drive

 Drive OP data Write

 Drive OP data Write

 System Information

 System Information

J-6090-199-A

BLX-104

Single Layer

J-6090-200-A

BLX-204

Dual Layer

J-2501-307-A

CD (HLX-A1)

J-2501-305-A

HLX-513

Single Layer (NTSC)

J-2501-306-A

HLX-514

Dual Layer (NTSC)

J-6090-077-A

HLX-506

Single Layer (PAL)

J-6090-078-A

HLX-507

Dual Layer (PAL)

Note: Refer to the service manual of BDP-BX1/S350 (Part No. 9-883-

989-1[]) (page 1-3 to 1-14E) for the use of BLX-104/204.

1. BLX-104
Procedure:
1. Select 

23.976Hz/1080p.

2.  Play “4.Motion picture”.
3.  Check whether player can play back or not.
4.  Check each outputs.
 Video:
 Composite/S 

Video/component/HDMI.

 Audio:
 Speaker 

out.

*  When 1080/24p monitor is nothing, 1080i (59.94Hz or 50Hz) 

can use instead of 1080/24p.

 

However this is temporary correspondence.

*  When the output of HDMI is 1080p, the signal of Composite/S 

Video/Component are not output.

 

It is necessary to lower the output of HDMI to 1080i or less.

2. BLX-204
Procedure:
1.  Select 1080i (59.94Hz or 50Hz).
2.  Play “4.Motion picture”.
3.  Check whether player can play back or not.
 

(Check the picture and sound output)

3. CD (HLX-A1)
Procedure:
Check whether player can play back or not.
(Check the sound output)

4.  HLX-513/514 (NTSC), HLX-506/507 (PAL)
Procedure:
1.  After displayed Main Menu, select “1.Video Signal”.
2.  Play “1.Color bar 100%”.
 

(Check the picture and sound output)

3.  Return to Menu.
4.  Play “Demonstration 4:3” or “Demonstration 16:9”.
 

(Check the picture and sound output)

1-2.  Playback operation confi rmation
Confi rm operation in each signal/output mode of test disc (BLX-
104/204) according to the content of the repair.

Note: “AV Sync.” doesn’t operate.

2. Networking Confi rmation
Confi rm it according to the following procedure when you confi rm 
the connection of the network.

Note: Do not execute “Network Connection Diagnostics” of “Network 

Settings” of the home menu with only the router connected.

Procedure:
1.  Connect the router with the unit with LAN cable.
2.  Turn on the power of the unit and the router.
3.  Press the [HOME] button on the remote commander, and the 

home menu is displayed.

4. Select 

“Setup” 

 “Network Settings”  “Internet Settings”, 

and press the [

] button on the remote commander.

5.  Select “View Networks Status” and press the [

] button on 

the remote commander.

6. Confi rm IP address are displayed in “IP Address”, “Subnet 

Mask” and “Default Gateway”.

IP Address Setting:

XXXX

Internet Access:

XXXX

Physical Connection:

XXXX

IP Address:

XXX.XXX.XXX.XXX

DNS Settings:

XXXX

MAC Address:

XXX.XXX.XXX.XXX

Primary DNS:

XXX.XXX.XXX.XXX

Secondary DNS:

XXX.XXX.XXX.XXX

Subnet Mask:

XXX.XXX.XXX.XXX

Default Gateway:

XXX.XXX.XXX.XXX

Procedure:
1.  Turn the power on.
2.  Input the following signal from Signal Generator to FM an-

tenna input directly.

Carrier frequency : A = 87.5 MHz, B = 98 MHz, C = 108 MHz
Deviation 

: 75 kHz

Modulation 

: 1 kHz

ANT input 

: 35 dBu (EMF)

Note: Please use 75 ohm “coaxial cable” to connect SG and the set. You 

cannot use video cable for checking.

 

  Please use SG whose output impedance is 75 ohm. 

 
3.  Set to FM tuner function and scan the input FM signal with 

automatic scanning.

4. Confi rm that input Frequency of A, B and C detected and auto-

matic scanning stops.

 
The stop of automatic scanning means “The station signal is re-
ceived in good condition”.

: