Sony DVP-S9 / MHC-S9D Service Manual ▷ View online
53
DVP-S9
Pin No.
Pin Name
I/O
Description
151
VRTA
I
A/D converter reference input terminal
152
VSS
—
Ground terminal (for digital system)
153 to 155
TESTK0 to TESTK2
I
Test signal input terminal (fixed at “L”)
156
XDSPRST
I
DSP reset signal input from the system controller (IC103) “L”: reset
157
XARPRST
I
ARP reset signal input from the system controller (IC103) “L”: reset
158
VSS
—
Ground terminal (for digital system)
159
MDS0
O
Spindle motor drive signal output to the FAN8034 (IC401)
160
MON
O
Motor ON/OFF signal output terminal Not used (open)
161
MDP0
O
Spindle motor drive signal output to the FAN8034 (IC401)
162
DFCT
O
Defect detection signal output terminal
163
JITPWM
O
Jitter PWM signal output terminal Not used (open)
164
LOCK
O
EFM lock detection signal output terminal Not used (open)
165
VDD1 1.8V
—
Power supply terminal (+1.8V) (for digital system)
166
GIO0/INT2
I
Inlimit sensor input terminal
167
GIO1/INT3
O
Spindle motor drive control signal output to the FAN8034 (IC401)
168
GIO2/INT4
I
TSD-M signal input from the FAN8034 (IC401)
169
GIO3/INT5
—
Not used (open)
170
VDD 3.3V
—
Power supply terminal (+3.3V) (for digital system)
171
GIO4/PGREF
—
Not used (open)
172
GIO5/PGIN
I
Monitor signal input from the SP3728AC (IC001)
173
GIO6/SDI
I
Serial data input from the SP3728AC (IC001)
174
GIO7/SDO
O
Serial data output to the SP3728AC (IC001)
175
GIO8/SCK
O
Serial clock signal output to the SP3728AC (IC001)
176
GIO9/FGREF
O
Motor drive signal output terminal Not used
177
GIO10/FGIN
O
Motor drive signal output terminal Not used
178
GIO11/TMC2
—
Not used (open)
179
GIO12
—
Not used (open)
180
GIO13
O
Serial data enable signal output to the SP3728AC (IC001)
181
VSS
—
Ground terminal (for digital system)
182
CLKIN
I
Clock signal input terminal
183
VSSA5
—
Ground terminal (for analog system)
184
VDDA5 1.8V
—
Power supply terminal (+1.8V) (for analog system)
185
DFCTI
I
Defect signal input from the SP3728AC (IC001)
186
VSS
—
Ground terminal (for digital system)
187
MCKI
I
Clock signal input terminal
188
VDD 1.8V
—
Power supply terminal (+1.8V) (for digital system)
189
SCKI
I
Clock signal input terminal
190
VSS
—
Ground terminal (for digital system)
191
TRST
I
Reset signal input terminal (for JTAG boundary scan)
192
TMS
I
MS signal input terminal (for JTAG boundary scan)
193
TDI
I
Serial data input terminal (for JTAG boundary scan)
194
TCK
I
Clock signal input terminal (for JTAG boundary scan)
195
TDO
O
Serial data output terminal (for JTAG boundary scan)
196
TZC
I
Tracking zero crossing signal input from the SP3728AC (IC001)
197
MIRR
I
Mirror detect signal input terminal from the SP3728AC (IC001)
54
DVP-S9
Pin No.
Pin Name
I/O
Description
198, 199
PWM0, PWM1
O
Sled motor drive signal output to the FAN8034 (IC401)
200
PWM2
O
Motor drive signal output terminal Not used
201
VDD 3.3V
—
Power supply terminal (+3.3V) (for digital system)
202, 203
PDM0, PDM1
O
Tracking coil drive signal output to the FAN8034 (IC401)
204, 205
PDM2, PDM3
O
Focusing coil drive signal output to the FAN8034 (IC401)
206
VSS
—
Ground terminal (for digital system)
207
XWR
I
Write enable signal input terminal
208
XRD
I
Read enable signal input terminal
55
DVP-S9
•
MAIN BOARD IC401 M30622MAA-B33FP (INTERFACE CONTROLLER)
Pin No.
Pin Name
I/O
Description
1 to 7
NC
—
Not used (open)
8
BYTE
I
External data bus line byte selection signal input “L”: 16 bits, “H”: 8 bits
Not used (fixed at “L”)
Not used (fixed at “L”)
9
CNVSS
—
Processor mode switch terminal (for test)
10
NC
—
Not used (fixed at “L”)
11
NC
—
Not used (open)
12
RESET
I
System reset signal input terminal
13
X-OUT
O
System clock output terminal (16 MHz)
14
VSS
—
Ground terminal
15
X-IN
I
System clock input terminal (16 MHz)
16
VCC
—
Power supply terminal (+5V)
17
NMI
I
Non-maskable interrupt input terminal Not used (fixed at “H”)
18
NC
—
Not used (open)
19
SYS CS
I
Chip select signal input from the system controller (IC103)
20 to 28
NC
—
Not used (open)
29
IIC-CLK
I/O
Communication data reading clock signal input or transfer clock signal output terminal
30
IIC-DATA
I/O
Communication data bus terminal
31
TXD1
I
Serial data input terminal (for test)
32
RXD1
O
serial data output terminal (for test)
33
CLK1
O
Serial clock signal output terminal (for test)
34
RTS1
O
RTS signal output terminal (for test)
35
SYS DATAOUT
O
serial data output to the system controller (IC103)
36
SYS DATAIN
I
serial data input from the system controller (IC103)
37
SYS CLK
O
Serial clock signal output to the system controller (IC103)
38
SYS POWER
O
Power ON/OFF control signal output terminal “H”: ON Not used (open)
39
NC
—
Not used (open)
40
SYS RST
O
System reset signal output terminal “L”: reset
41
NO-USE
—
Not used (fixed at “L”)
42
SYS RQ
O
Interrupt request signal output to the system controller (IC103)
43
SYS OK
O
System OK signal output to the system controller (IC103)
44
P.CONT
O
Power block ON/OFF control signal output terminal “H”: ON
45
NC
—
Not used (open)
46
NC
—
Not used (fixed at “H”)
47
DVDFRCHK
O
Flash memory (for DVD) check signal output terminal Not used (fixed at “H”)
48
VMUTE
O
Mute signal output to the video buffer (IC701) “H”: mute
49, 50
NC
—
Not used (open)
51
NC
—
Not used (fixed at “H”)
52
NC
—
Not used (open)
53
B-TRIG
O
Deck-B trigger plunger drive signal output terminal “H”: trigger plunger on
54
ECO CHECK
—
Not used (fixed at “H”)
55
A-TRIG
O
Deck-A trigger plunger drive signal output terminal “H”: trigger plunger on
56 to 58
NC
—
Not used (open)
59
REC/PB/PASS
O
Recording/playback/pass selection signal output terminal
“L”: recording, center voltage: playback, “H”: pass
“L”: recording, center voltage: playback, “H”: pass
60, 61
NC
—
Not used (open)
56
DVP-S9
Pin No.
Pin Name
I/O
Description
62
VCC
—
Power supply terminal (+5V)
63
SOFT-TEST
O
For software check terminal Not used (open)
64
VSS
—
Ground terminal
65 to 68
LED_DISC1
O
LED drive signal output of the 1 indicator (D705) “L”: LED on
69 to 72
LED_DISC2
O
LED drive signal output of the 2 indicator (D704) “L”: LED on
73 to 76
LED_DISC3
O
LED drive signal output of the 3 indicator (D703) “L”: LED on
77 to 80
LED_PLAY
O
LED drive signal output of the N indicator (D702) “L”: LED on
81 to 83
LED_PAUSE
O
LED drive signal output of the X indicator (D701) “L”: LED on
84
EXP-IN DATA
I
Serial data input terminal
85
EXP-OUT DATA
O
Serial data output terminal
86
EXP-LAT
O
Serial data latch pulse signal output terminal
87
EXP-CLK
O
Serial clock signal output terminal
88
LED_PAUSE
O
LED drive signal output of the X indicator (D701) “L”: LED on
89
A-SHUT
I
Shut off (deck-A) detection signal input terminal
90
B-SHUT
I
Shut off (deck-B) detection signal input terminal
91
B-HALF
I
Detection input terminal from the deck-B cassette detect switch “L”: cassette in
92
MODEL-IN
I
Model destination setting terminal
93
PWRCHK
—
Power check terminal Fixed at “H”
94
KEY2
I
Key input terminal
95
KEY1
I
Key (S711 to S720) input terminal (A/D input)
96
AVSS
—
Ground terminal (for A/D converter)
97
KEY0
I
Key (S701 to S708) input terminal (A/D input)
98
VREF
I
Reference voltage (+5V) input terminal (for A/D converter)
99
AVCC
—
Power supply terminal (+5V) (for A/D converter)
100
NC
—
Not used (open)
Click on the first or last page to see other DVP-S9 / MHC-S9D service manuals if exist.