Sony DVP-S9 / MHC-S9D Service Manual ▷ View online
17
DVP-S9
2.
CD
Select
[2]
, insert CD disc, and press
[ENTER]
key, and the adjust-
ment will be made through the following steps, then adjusted val-
ues will be written to the EEPROM.
ues will be written to the EEPROM.
CD Adjustment Steps
1. Sled Tilt Rest
2. Disc Check Memory CD
3. Wait 500 msec
4. Set Disc Type CD
5. LD ON
6. Spdl Start
7. Wait 500 msec
8. Focus Servo ON 0
9. Auto Track Offset Adjust
1. Sled Tilt Rest
2. Disc Check Memory CD
3. Wait 500 msec
4. Set Disc Type CD
5. LD ON
6. Spdl Start
7. Wait 500 msec
8. Focus Servo ON 0
9. Auto Track Offset Adjust
10. CLVA ON
11. Wait 500 msec
12. Tracking ON
13. (TC Display Start)
14. Wait 1 sec
15. Jitter Display Start
16. Sled ON
17. Check CLV ON
18. Auto LFO Adjust
19. Auto Focus Offset Adjust
20.
21. Auto Focus Gain Adjust
22. Auto Focus Offset Adjust
23. Eq Boost Adjust
24. Auto LFO Adjust
25. Auto Track Gain Adjust, Search Check
26. 32Tj Fwd
27. 32Tj Rev
28. 500Tj Fwd
29. 500Tj Rev
11. Wait 500 msec
12. Tracking ON
13. (TC Display Start)
14. Wait 1 sec
15. Jitter Display Start
16. Sled ON
17. Check CLV ON
18. Auto LFO Adjust
19. Auto Focus Offset Adjust
20.
21. Auto Focus Gain Adjust
22. Auto Focus Offset Adjust
23. Eq Boost Adjust
24. Auto LFO Adjust
25. Auto Track Gain Adjust, Search Check
26. 32Tj Fwd
27. 32Tj Rev
28. 500Tj Fwd
29. 500Tj Rev
30. All Servo Stop
3.
DVD-DL (dual layer)
Select
[3]
, insert DVD dual layer disc, and press
[ENTER]
key,
and the adjustment will be made through the following steps, then
adjusted values will be written to the EEPROM.
adjusted values will be written to the EEPROM.
DVD Dual Layer Disc Adjustment Steps
1. Sled Tilt Reset
2. Disc Check Memory DL
3. Wait 500 msec
4. Set Disc Type DL
5. LD ON
6. Spdl Start
7. Wait 1 sec, Layer 1 Adjust
8. Focus Servo ON 0
9. Auto Track Offset Adjust
1. Sled Tilt Reset
2. Disc Check Memory DL
3. Wait 500 msec
4. Set Disc Type DL
5. LD ON
6. Spdl Start
7. Wait 1 sec, Layer 1 Adjust
8. Focus Servo ON 0
9. Auto Track Offset Adjust
10. Clva ON
11. Wait 500 msec
12. Tracking ON
13. Wait 500 msec
14. Sled ON
15. Check CLV Lock
16. Auto Loop Filter Offset Auto Focus Adjust
17.
18. Auto Focus Gain Adjust
19. Auto Focus Offset Adjust
20. Eq Boost Adjust
21. Auto Loop Filter Offset
22. Auto Track Gain Adjust, Search Check
23. 32Tj Fwd
24. 32Tj Rev
25. 500Tj Fwd
26. 500Tj Rev, Layer 0 Adjust
27. Fj (L1 -> L0)
28. Auto Track Offset Adjust L0
11. Wait 500 msec
12. Tracking ON
13. Wait 500 msec
14. Sled ON
15. Check CLV Lock
16. Auto Loop Filter Offset Auto Focus Adjust
17.
18. Auto Focus Gain Adjust
19. Auto Focus Offset Adjust
20. Eq Boost Adjust
21. Auto Loop Filter Offset
22. Auto Track Gain Adjust, Search Check
23. 32Tj Fwd
24. 32Tj Rev
25. 500Tj Fwd
26. 500Tj Rev, Layer 0 Adjust
27. Fj (L1 -> L0)
28. Auto Track Offset Adjust L0
29. Clva ON
30. Wait 500 msec
31. Tracking ON
32. Wait 500 msec
33. Sled ON
34. Check CLV Lock
35. Auto Focus Filter Offset
36. Auto Focus Adjust
37.
38. Auto Focus Gain Adjust
39. Auto Focus Offset Adjust
40. Eq Boost Adjust
41. Auto Loop Filter Offset
42. Auto Track Gain Adjust, Search Check
43. 32Tj Fwd
44. 32Tj Rev
45. 500Tj fwd
46. 500Tj Rev, Layer Jump Check
47. Lj (L0 -> L1)
48. Lj (L1 -> L0)
30. Wait 500 msec
31. Tracking ON
32. Wait 500 msec
33. Sled ON
34. Check CLV Lock
35. Auto Focus Filter Offset
36. Auto Focus Adjust
37.
38. Auto Focus Gain Adjust
39. Auto Focus Offset Adjust
40. Eq Boost Adjust
41. Auto Loop Filter Offset
42. Auto Track Gain Adjust, Search Check
43. 32Tj Fwd
44. 32Tj Rev
45. 500Tj fwd
46. 500Tj Rev, Layer Jump Check
47. Lj (L0 -> L1)
48. Lj (L1 -> L0)
49. All Servo Stop
Ver 1.6
18
DVP-S9
0.
Disc Check Memory
Disc Check
1. SL Disc Check
2. CD Disc Check
3. DL Disc Check
0. Reset SLED TILT
_
On this screen, the mirror time is measured to judge the disc and it
is written to the EEPROM. First load DVD SL disc and press
is written to the EEPROM. First load DVD SL disc and press
[1]
,
next load CD disc and press
[2]
, and finally load DVD DL disc
and press
[3]
.
The adjustment must be executed more than once after default
data were written. External vibration or shock to the player must
not be given. Reference value for DVD is from 10 to 20, and for
CD, from 28 to 4F.
Check that the value of CD is larger than that of DVD.
When those values are beyond a range perform this adjustment
again.
From this screen, you can go to another mode by
pressing
data were written. External vibration or shock to the player must
not be given. Reference value for DVD is from 10 to 20, and for
CD, from 28 to 4F.
Check that the value of CD is larger than that of DVD.
When those values are beyond a range perform this adjustment
again.
From this screen, you can go to another mode by
pressing
>
or
.
key, but you cannot enter this mode from
another mode. You can enter this mode from the Operation Menu
screen only.
screen only.
[DRIVE MANUAL OPERATION]
On the Test Mode Menu screen, select
[2]
, and the manual opera-
tion menu will be displayed. For the manual operation, each servo
on/off control and adjustment can be executed manually.
on/off control and adjustment can be executed manually.
## Drive Manual Operation ##
Operation Menu
1. Disc type
2. Servo Control
3. Track/Layer Jump
4. Manual Adjustment
5. Auto Adjustment
6. Memory Check
7. Sacd Water Mark
0. Disc Check Memory
_
Exit: Return
In using the manual operation menu, take care of the following
points. These commands do not provide protection, thus requiring
correct operation. The sector address or time code field is dis-
played when a disc is loaded.
points. These commands do not provide protection, thus requiring
correct operation. The sector address or time code field is dis-
played when a disc is loaded.
1. Set correctly the disc type to be used on the Disc Type
screen.
The disc type must be set after a disc was loaded.
The set disc type is cleared when the tray is opened.
The disc type must be set after a disc was loaded.
The set disc type is cleared when the tray is opened.
2. After power ON, if the Drive Manual Operation was se-
lected, first perform “Reset SLED TILT” by opening 1.
Disc Type screen.
Disc Type screen.
3. In case of an alarm, immediately press the
x
button to
stop the servo operation, and turn the power OFF.
Basic operation (controllable from front panel or remote com-
mander)
mander)
I/1
Power OFF
x
Servo stop
Z
Stop+Eject/Loading
[RETURN]
Return to Operation Menu or Test Mode
Menu
Menu
>
,
.
Transition between sub modes of menu
[1]
to
[9]
,
[10/0]
Selection of menu items
Cursor
↑
/
↓
Increase/Decrease in manually adjusted
value
value
1.
Disc Type
Disc Type
1. Disc Type Auto Check
2. DVD SL
12 cm
3. DVD DL
12 cm
4. CD
12cm
5. LCD
12 cm
6. DVD SL
8 cm
7. DVD DL
8 cm
8. CD
8 cm
9. LCD
8 cm
0. Reset SLED TILT
-- SA. ------ SI. --
EMG. 00
DVD SL12cm
On this screen, select the disc type. To select the disc type, press
the number of the loaded disc. The selected disc type is displayed
at the bottom. Selecting
the number of the loaded disc. The selected disc type is displayed
at the bottom. Selecting
[1]
automatically selects and displays the
disc type. In case of wrong display, retry “Disc Check Memory”.
Also, opening the tray causes the set disc type to be cleared. In
this case, set the disc type again after loading.
In performing manual operation, the disc type must be set.
Once the disc type has been selected, the sector address or time
code display field will appear as shown below. These values are
displayed when PLL is locked.
Also, opening the tray causes the set disc type to be cleared. In
this case, set the disc type again after loading.
In performing manual operation, the disc type must be set.
Once the disc type has been selected, the sector address or time
code display field will appear as shown below. These values are
displayed when PLL is locked.
Ver 1.6
19
DVP-S9
Disc Type
1. Disc Type Auto Check
2. DVD SL
12 cm
3. DVD DL
12 cm
4. CD
12cm
5. LCD
12 cm
6. DVD SL
8 cm
7. DVD DL
8 cm
8. CD
8 cm
9. LCD
8 cm
0. Reset SLED TILT
SA. SI. EMG. 00
DVD SL 12 cm
Display when DVD SL 12cm disc was selected
Disc Type
1. Disc Type Auto Check
2. DVD SL
12 cm
3. DVD DL
12 cm
4. CD
12cm
5. LCD
12 cm
6. DVD SL
8 cm
7. DVD DL
8 cm
8. CD
8 cm
9. LCD
8 cm
0. Reset SLED TILT
TC. : : EMG. 00
CD 12 cm
Display when CD 12cm disc was selected
[0]
Reset SLED TILT
Reset the Sled and Tilt to initial posi-
tion.
tion.
[1]
Disk Type Check
Judge automatically the loaded disc. As
the judged result is displayed at the bot-
tom of screen, make sure that it is cor-
rect.
If Disc Check Memory menu has not
been executed after EEPROM default
setting, the disc type cannot be judged.
In this case, return to the initial menu
and make a check for three types of
discs (SL, DL, CD).
the judged result is displayed at the bot-
tom of screen, make sure that it is cor-
rect.
If Disc Check Memory menu has not
been executed after EEPROM default
setting, the disc type cannot be judged.
In this case, return to the initial menu
and make a check for three types of
discs (SL, DL, CD).
[2]
to
[9]
Select the loaded disc. The adjusted
value is written to the address of se-
lected disc. No further entry is neces-
sary if
value is written to the address of se-
lected disc. No further entry is neces-
sary if
[1]
was selected.
[10/0]
Reset SLED TILT
Reset the Sled
and Tilt to initial position.
[1]
LD
Turn ON/OFF the laser.
[2]
SP
Turn ON/OFF the spindle.
[3]
Focus
Search the focus and turn on the focus.
[4]
TRK
Turn ON/OFF the tracking servo.
[5]
Sled
Turn ON/OFF the sled servo.
[6]
CLVA
Turn ON/OFF normal servo of spindle
servo.
servo.
[7]
FCS. Srch
Apply same voltage as that of focus
search to the focus drive to check the
focus drive system.
search to the focus drive to check the
focus drive system.
→ Sled FWD
Move the sled outward. Perform this
operation with the tracking servo turned
off.
off.
← Sled REV
Move the sled inward. Perform this op-
eration with the tracking servo turned
off.
eration with the tracking servo turned
off.
↑ Tilt UP
Move the tilt upward.
↓ Tilt DOWN
Move the tilt downward.
The following menus are normally not used.
3.
Track/Layer Jump
4.
Manual Adjustment
5.
Auto Adjustment
The persons who do not know well about these menus should not
use them.
use them.
2. Servo Control
Servo Control
1. LD
Off R.Sled FWD
2. SP
Off L.Sled REV
3. Focus
Off
4. TRK.
Off
5. Sled
Off
6. CLVA
Off
7. FCS. Srch Off
0. Reset SLED TILT
SA. SI. EMG. 00
DVD SL 12 cm
On this screen, the servo on/off control necessary for replay is
executed. Normally, turn on each servo from 1 sequentially and
when CLVA is turned on, the usual trace mode becomes active. In
the trace mode, DVD sector address or CD time code is displayed.
This is not displayed where the spindle is not locked.
The spindle could run overriding the control if the spindle system
is faulty or RF is not present. In such a case, do not operate CLVA.
executed. Normally, turn on each servo from 1 sequentially and
when CLVA is turned on, the usual trace mode becomes active. In
the trace mode, DVD sector address or CD time code is displayed.
This is not displayed where the spindle is not locked.
The spindle could run overriding the control if the spindle system
is faulty or RF is not present. In such a case, do not operate CLVA.
Ver 1.6
20
DVP-S9
[EMERGENCY HISTORY]
### EMG. History ###
Laser Hours
CD
xxxxxxxh
DVD
xxxxxxxh
1. 00 00 00 00
00 00 00 00
00 00 00 00
00 00 00 00
2. 00 00 00 00
00 00 00 00
00 00 00 00
00 00 00 00
Select: 1 – 9
Scroll: UP/DOWN
(1: Last EMG.)
Exit: RETURN
On the Test Mode Menu screen, selecting
[4]
displays the infor-
mation such as servo emergency history. The history information
from last 1 up to 10 can be scrolled with
from last 1 up to 10 can be scrolled with
↑
key or
↓
key. Also,
specific information can be displayed by directly entering that
number with ten keys.
number with ten keys.
The upper two lines display the laser ON total hours. Data below
minutes are omitted.
minutes are omitted.
Clearing History Information
Clearing laser hours
Press
Press
[DVD DISPLAY]
and
[CLEAR]
keys in this order.
Both CD and DVD data are cleared.
Clearing emergency history
Press
Clearing emergency history
Press
[TITLE]
and
[CLEAR]
keys in this order.
Initializing set up data
Press
Press
[DVD SET UP]
and
[CLEAR]
keys in this order.
The data have been initialized when “Set Up Initialized” mes-
sage is displayed. The EMG. History screen will be restored
soon.
sage is displayed. The EMG. History screen will be restored
soon.
How to see Emergency History
1
: Emergency Code
2
: Don’t Care
These codes are used for verification of software designing.
3
: Historical order 1 to 9
3
1.
1
2
2
6. Memory Check
EEPROM Data1
-– DL –-
CD LCD
SL
L0
L1
Focus Gain
xx xx
xx
xx
xx
TRK. Gain
xx xx
xx
xx
xx
FCS Balance
xx xx
xx
xx
xx
Focus Bias
xx xx
xx
xx
xx
TRV. Offset
xx xx
xx
xx
xx
L. F. Offset
xx xx
xx
xx
xx
EQ Boost
xx xx
xx
xx
xx
Mirror Time
xx xx
xx
xx
xx
_DOWN: Next Data
CLEAR: Default Set page.1/2
EEPROM Data1
-– DL –-
CD LCD
SL
L0
L1
RF Jitter
xx --
xx
xx
xx
RF Level
xx --
xx
--
--
FE Level
xx --
xx
--
--
FE Balance
xx --
xx
--
--
TRV. Level
xx --
xx
--
--
Analog FRSW
xx xx
xx
xx
xx
PLL DacGain
xx xx
xx
xx
xx
_
UP : Prev Data
CLEAR: Default Set page.2/2
This screen displays current servo adjusted data stored in the
EEPROM. Though adjusted data can be initialized with the
EEPROM. Though adjusted data can be initialized with the
[CLEAR]
key, they cannot be restored after initialization.
So, before clearing, make a note of the adjusted data.
For reference, the drive has been designed so that the gain center
value is 20 and offset value is 80. Other values will be in a range
of 10 to 80. If extreme value such as 00 or FF is set, adjustment
will be faulty. In such a case, check for disc scratch or cable dis-
connection, then perform adjustment again.
For reference, the drive has been designed so that the gain center
value is 20 and offset value is 80. Other values will be in a range
of 10 to 80. If extreme value such as 00 or FF is set, adjustment
will be faulty. In such a case, check for disc scratch or cable dis-
connection, then perform adjustment again.
[MECHA AGING]
### Mecha Aging ###
Press OPEN Key
Abort: STOP key
On the Test Mode Menu Screen, selecting
[3]
executes the aging
of the mechanism. Start aging with PLAY. During aging, the re-
peat cycle is displayed. Aging can be aborted at any time by press-
ing the
peat cycle is displayed. Aging can be aborted at any time by press-
ing the
x
key. After the operation is stopped, press the
x
key
or
[RETURN]
key again to return to the Test Mode Menu.
SEARCH Aging is only for a CD.
Ver 1.6
Click on the first or last page to see other DVP-S9 / MHC-S9D service manuals if exist.