Sony DVP-S9 / MHC-S9D Service Manual ▷ View online
DVP-S9
9
3-6.
MAIN BOARD
3-7.
FRONT PANEL SECTION
2
connector
(CN401)
(CN401)
1
wire (flat type) (10 core)
(CN107)
(CN107)
3
two connectors
(CN101, 102)
(CN101, 102)
9
MAIN board
7
screw
(BVTP3
(BVTP3
×
8)
5
screw
(BVTP3
(BVTP3
×
8)
6
lug
4
connector
(CN701)
(CN701)
8
screw
(BVTP3
(BVTP3
×
8)
2
three screws
(BVTP3
(BVTP3
×
8)
3
two claws
1
connector
(CN401)
(CN401)
4
front panel section
3
claw
DVP-S9
10
3-9.
LID (CD)
3-8.
PANEL BOARD, SUB PANEL BOARD
5
two claws
4
four screws
(BVTP2.6
(BVTP2.6
×
8)
6
SUB PANEL board
1
five screws
(BVTP2.6
(BVTP2.6
×
8)
3
PANEL board
2
two claws
3
lid (CD)
4
spring (CD)
1
screw
(BVTP2.6
(BVTP2.6
×
8)
2
bracket (LID) assy
11
DVP-S9
SECTION 4
TEST MODE
Note:
Use following buttons in the test mode.
no mark : Button of DVD/video CD/CD player (DVP-S9)
*1
: Button of A/V amplifier (TA-S9D)
*2
: Button of tuner (ST-S9)
[CHANGE-OVER THE COLOR SYSTEM]
• The color system can be changed over NTSC or PAL.
Procedure:
1. Press the
Procedure:
1. Press the
I/1
*
1
button to turn the power on.
2. Turn the
[FUNCTION]
*
1
knob to select
“DVD”, and press
the
x
button.
3. While pressing the both
[RETURN]
and
[REPEAT]
buttons,
turn the power off.
4. Press the
I/1
*
1
button to turn the power on. The color sys-
tem is changed over.
[COLD RESET]
• The cold reset clears all data including preset data stored in the
RAM to initial conditions. Execute this mode when returning
the set to the customer.
the set to the customer.
Procedure 1:
1. Press the
1. Press the
I/1
*
1
button to turn the power on.
2. While pressing the both
[PLAY MODE]
and
x
buttons, press
the
M
button.
3. The set is reset, and becomes standby state.
Procedure 2:
1. Press the
1. Press the
I/1
*
1
button to turn the power on.
2. While pressing the
[DIGITAL]
*
1
button, press the
[DISPLAY]
*
2
button.
3. The set is reset, and becomes standby state.
[DVD DELIVERY MODE]
• This mode moves the optical pick-up to the position durable to
vibration. Use this mode when returning the set to the customer
after repair.
after repair.
Procedure:
1. Press the
1. Press the
I/1
*
1
button to turn the power on.
2. Turn the
[FUNCTION]
*
1
knob to select “DVD”.
3. While pressing the
[EQ ON/OFF]
*
1
button, press the
I/1
*
1
button.
4. The message “LOCK” is displayed on the fluorescent indica-
tor tube of tuner unit and turn the power off automatically, and
the DVD delivery mode is set.
the DVD delivery mode is set.
[GC TEST MODE]
Enter the GC Test Mode
Procedure 1:
1. Press the
1. Press the
I/1
*
1
button to turn the power on.
2. While pressing the both
[PLAY MODE]
and
x
buttons, press
the
Z
(DISC 1) button.
3. LEDs and fluorescent indicator tube are all turned on of all
units.
Procedure 2:
1. Press the
1. Press the
I/1
*
1
button to turn the power on.
2. While pressing the both
[STEREO/MONO]
*
2
and
[CINEMA STUDIO C]
*
1
buttons, press the
[CLOCK/TIMER]
*
2
button.
3. LEDs and fluorescent indicator tube are all turned on of all
units.
Version Display Mode
Procedure:
1. Enter the GC test mode.
2. Each time the
1. Enter the GC test mode.
2. Each time the
[DISC 1]
or
[TUNER MEMORY]
*
2
button is
pressed, microcomputer or mechanism deck version is dis-
played of each unit.
played of each unit.
3. Press the
[DISC 3]
or
[TUNING +]
*
2
button to detail is dis-
played the version.
Key Check Mode
Procedure:
1. Enter the GC test mode.
2. Press the
1. Enter the GC test mode.
2. Press the
[DISC 2]
or
[TUNING --]
*
2
button to set the key check
mode, and displays “K 0 J 0 V 0” on the fluorescent indicator
tube of tuner unit.
tube of tuner unit.
3. All buttons are pressed of video CD unit, all LEDs are blink-
ing of video CD unit. (not change the display of fluorescent
indicator tube)
indicator tube)
Releasing the GC Test Mode
To release from this mode, press three buttons in the same manner
as entering this mode or disconnect the power cord.
as entering this mode or disconnect the power cord.
[DVD SERVICE MODE]
• This mode can run the DVD sled motor optionally. Use this
mode, for instance, when cleaning the optical pick-up.
Procedure:
1. Press the
1. Press the
I/1
*
1
button to turn the power on.
2. Turn the
[FUNCTION]
*
1
knob to select “DVD”.
3. While pressing the both
[PLAY MODE]
and
x
buttons, press
the
.
button.
4. Set to the DVD service mode.
5. With the DVD in stop status, press the
5. With the DVD in stop status, press the
M
button to move
the optical pick-up to outside track, or press the
m
button
to inside track.
6. To release from this mode, perform as follows.
1) Move the optical pick-up to the most inside track.
2) Disconnect the power cord.
2) Disconnect the power cord.
Notes:
• Always move the optical pick-up to most inside track when
releasing from this mode. Otherwise, a disc will not be un-
loaded.
loaded.
• Do not run the sled motor excessively, otherwise the gear can
be chipped.
[DVD CANCELLATION MODE OF REPEAT LIMI-
TATION]
TATION]
• This mode can cancel the DVD repeat limitation (5 times).
Procedure:
1. Press the
Procedure:
1. Press the
I/1
*
1
button to turn the power on.
2. Turn the
[FUNCTION]
*
1
knob to select “DVD”.
3. While pressing the both
[PLAY MODE]
and
x
buttons, press
the
[REPEAT]
button.
4. DVD repeat limitation is canceled.
5. To release this mode, disconnect the power cord.
5. To release this mode, disconnect the power cord.
[DVD DISC TRAY LOCK MODE FOR BURGLARY
PREVENTION]
PREVENTION]
Procedure:
1. Press the
1. Press the
I/1
*
1
button to turn the power on.
2. Turn the
[FUNCTION]
*
1
knob to select “DVD”.
3. While pressing the both
[PLAY MODE]
and
x
buttons, press
the
m
button, turn the power off.
12
DVP-S9
[GENERAL DESCRIPTION]
The Test Mode allows you to make diagnosis and adjustment eas-
ily using the remote commander and monitor TV. The instructions,
diagnostic results, etc. are given on the on-screen display (OSD).
ily using the remote commander and monitor TV. The instructions,
diagnostic results, etc. are given on the on-screen display (OSD).
[STARTING TEST MODE]
1.
Press the
I/1
*
1
button to turn the power on.
2.
Turn the
[FUNCTION]
*
2
knob to select “DVD”.
3.
While pressing the
x
and
[PLAY MODE]
button, press
the
.
button to enter the test mode.
4.
It displays “TEST MODE” on the fluorescent indicator tube,
and displays the Test Mode Menu on the monitor screen as
follows. (At the bottom of the menu screen, the model name
and revision number are displayed)
and displays the Test Mode Menu on the monitor screen as
follows. (At the bottom of the menu screen, the model name
and revision number are displayed)
Test Mode Menu
0. Syscon Diagnosis
1. Drive Auto Adjustment
2. Drive Manual Operation
3. Mecha Aging
4. Emergency History
5. Version Information
6. Video Level Adjustment
Exit: POWER Key
_
Model
: xxx-xxxx_xx
Revision : 1.xxx
5.
To execute each function, select the desired menu and press its
number on the remote commander (RM-SD390AV or RM-
SD395AV).
number on the remote commander (RM-SD390AV or RM-
SD395AV).
6.
To release from test mode, press the
I/1
*
1
button and turn
the power off.
1.
All
All items continuous check
This menu checks all diagnostic items continuously. Normally, all
items are checked successively one after another automatically un-
less an error is found, but at a certain item that requires judgment
through a visual check to the result, the following screen is dis-
played for the key entry.
This menu checks all diagnostic items continuously. Normally, all
items are checked successively one after another automatically un-
less an error is found, but at a certain item that requires judgment
through a visual check to the result, the following screen is dis-
played for the key entry.
### Syscon Diagnosis ###
Diag All Check
No. 2 Version
2-3. ROM Check Sum
Check Sum = 2005
Press NEXT Key to Continue
Press PREV Key to Repeat
_
For the ROM Check, the check sum calculated by the Syscon is
output, and therefore you must compare it with the specified value
for confirmation.
Following the message, press
output, and therefore you must compare it with the specified value
for confirmation.
Following the message, press
>
key to go to the next item,
or
.
key to repeat the same check again. To quit the diagnosis
and return to the Check Menu screen, press
x
or
[ENTER]
key.
If an error occurred, the diagnosis is suspended and the error code
is displayed as shown below.
is displayed as shown below.
### Syscon Diagnosis ###
3-3. EEPROM Check
Error 03: EEPROM Write/Reed N
Address
: 00000001
Write Data : 2492
Read Data
: 2490
Press NEXT Key to Continue
Press PREV Key to Repeat
_
[SYSCON DIAGNOSIS]
The same contents as board detail check by serial interface can be
checked from the remote commander.
On the Test Mode Menu screen, press
checked from the remote commander.
On the Test Mode Menu screen, press
[10/0]
key on the remote
commander, and the following check menu will be displayed.
### Syscon Diagnosis ###
Check Menu
0. Quit
1. All
2. Version
3. Peripheral
4. Servo
5. Supply
6. AV Decoder
7. Video
8. Audio
_
0.
Quit
Quit the Syscon Diagnosis and return to the Test Mode Menu.
Press
x
key to quit the diagnosis, or
>
key to repeat the same
item where an error occurred, or
.
key to continue the check
from the item next to faulty item.
Ver 1.6
Click on the first or last page to see other DVP-S9 / MHC-S9D service manuals if exist.