Sony DHC-AZ33D / HCD-AZ33D Service Manual ▷ View online
HCD-AZ33D
25
To Clear the Initialize Setup Data
Press [DVD MENU] button and then press [CLEAR] button on the
remote commander.
Press [DVD MENU] button and then press [CLEAR] button on the
remote commander.
Emg. History Check
Laser Hours CD 999h 59min
DVD 999h 59min
initialize setup data...
[Next] Next Page [Prev] Prev Page
[0] Return to Top Menu
To Return to the Top Menu of Remocon Diagnosis
Menu
Press the [0] button on the remote commander.
Menu
Press the [0] button on the remote commander.
5. CHECKING VERSION INFORMATION
To check the version information, please follow the following pro-
cedure.
Procedure:
1. From the top menu of Remocon Diagnosis Menu, select “4.
To check the version information, please follow the following pro-
cedure.
Procedure:
1. From the top menu of Remocon Diagnosis Menu, select “4.
Version Information” by pressing the [4] button on the remote
commander. The following screen appears on the on-screen
display.
commander. The following screen appears on the on-screen
display.
Version information
Firm(Main): Ver. X.XXX
Firm(Sub): XX.XX
RISC: XXXXXX
8032: XXXXXX
Audio DSP: XX.XX.XX.XX
Servo DSP: XX.XX.XX.XX
[0]Return to Top Menu
2. To return to the top menu of Remocon Diagnosis Menu, press
the [0] on the remote commander.
DIGITAL MEDIA PORT TEST
Procedure:
1. Connect the DMPORT CHECK JIG (Part No.: J-2501-309-A)
Procedure:
1. Connect the DMPORT CHECK JIG (Part No.: J-2501-309-A)
with the terminal DMPORT.
2. Press the [
?/1
] button to turn the power on.
3. Confi rm that both LEDs of the DMPORT confi rmation JIG
lights. (Confi rmation the power supply line.)
4. Touch the [DMPORT] sensor to select the “DMPORT”
5. Touch three sensors of [
5. Touch three sensors of [
x
], [DMPORT] and [VOLUME +]
simultaneously, the DMPORT test mode is activated.
6. Touch three sensors of [
x
], [DMPORT] and [VOLUME -] si-
multaneously, it is confi rmed that “DMPORT OK” is displayed
on this set display. (Confi rmation of communication line)
on this set display. (Confi rmation of communication line)
7. To a pinjack of the DMPORT confi rmation JIG input informa-
tion relevant to audio signal. (sine-wave 1.0Vrms)
8. Confi rm the output of speakers and monitor TV. (Confi rmation
of analog signal)
9. To release from this mode, press the [
?/1
] button to turn off
the system.
DMPORT
check jig
(Part No.:
J-2501-309-A)
J001
AF oscillator
set
FL/FR
speaker
DMPORT board
CN204
SPEAKER board
TB501
Ver. 1.1
HCD-AZ33D
26
SECTION 5
MECHANICAL ADJUSTMENTS
SECTION 6
ELECTRICAL ADJUSTMENTS
PRECAUTION
1. Clean the following parts with a denatured-alcohol-moistened
1. Clean the following parts with a denatured-alcohol-moistened
swab :
record/playback head
pinch roller
erase head
rubber belts
capstan
idlers
2. Demagnetize the record/playback head with a head demagne-
tizer.
3. Do not use a magnetized screwdriver for the adjustments.
4. After the adjustments, appiy suitable locking compound to the
4. After the adjustments, appiy suitable locking compound to the
parts adjusted.
5. The adjustments should be performed with the rated power
supply voltage unless otherwise noted.
• Torque
Measurement
Mode
Torque Meter
Meter Reading
FWD
CQ-102C
3.06 N • m to 6.96 N • m
31 to 71 g • cm
(0.43 – 0.98 oz • inch)
FWD
Back Tension
Back Tension
CQ-102C
0.19 N • m to 0.58 N • m
2 to 6 g • cm
(0.02 – 0.08 oz • inch)
REV
CQ-102RC
3.06 N • m to 6.96 N • m
31 to 71 g • cm
(0.43 – 0.98 oz • inch)
REV
Back Tension
Back Tension
CQ-102RC
0.19 N • m to 0.58 N • m
2 to 6 g • cm
(0.02 – 0.08 oz • inch)
FF/REW
CQ-201B
6.96 N • m to14.02 N • m
71 to 143 g • cm
(0.98 – 1.99 oz • inch)
FWD Tension
CQ-403A
9.80 N • m
100 g or more
(3.53 oz or more)
REV Tension
CQ-403R
9.80 N • m
100 g or more
(3.53 oz or more)
1. Demagnetize the record/playback head with a head demagne-
tizer.
2. Do not use a magnetized screwdriver for the adjustments.
3. After the adjustments, apply suitable locking compound to the
3. After the adjustments, apply suitable locking compound to the
parts adjust.
TEST TAPE
Tape
Signal
Used for
P-4-A063
6.3 kHz, -10 dB
Azimuth Adjustment
RECORD/PLAYBACK HEAD AZIMUTH ADJUSTMENT
Note: Perform this adjustments for both decks.
Procedure:
1. Mode: Playback
1. Mode: Playback
set
MAIN board
VIDEO/SAT OUT
jack (J101)
VIDEO/SAT OUT
jack (J101)
+
–
level meter
test tape
P-4-A063
(6.3 kHz, –10 dB)
P-4-A063
(6.3 kHz, –10 dB)
2. Turn the adjustment screw and check output peaks. If the peaks
do not match for L-CH and R-CH, turn the adjustment screw
so that outputs match within 1dB of peak.
so that outputs match within 1dB of peak.
Screw
position
L-CH
peak
within
1dB
Output
level
L-CH
peak
R-CH
peak
within
1dB
Screw
position
R-CH
peak
DECK SECTION
0 dB = 0.775V
HCD-AZ33D
27
3. Mode: Playback
set
test tape
P-4-A063
(6.3 kHz, –10 dB)
oscilloscope
V
H
waveform of oscilloscope
in phase 45
°
90
° 135° 180°
good
wrong
MAIN board
VIDEO/SAT OUT
jack (J101)
VIDEO/SAT OUT
jack (J101)
4. After the adjustments, apply suitable locking compound to the
pats adjusted.
Adjustment Location: Record/Playback/Erase Head
Note: Holder (cassette) of front panel to detach.
reverse
forward
DVD SECTION
TEST DISC LIST
Use the following test disc on electrical adjustments.
YEDS-18 (CD)
Use the following test disc on electrical adjustments.
YEDS-18 (CD)
: PART No. 3-702-101-01
PATD-012 (CD)
: PART No. 4-225-203-01
HLX-503 (DVD-SL) (NTSC) : PART No. J-6090-069-A
HLX-504 (DVD-SL) (NTSC) : PART No. J-6090-088-A
HLX-506 (DVD-SL) (PAL) : PART No. J-6090-077-A
HLX-501 (DVD-DL) (NTSC) : PART No. J-6090-071-A
HLX-505 (DVD-DL) (NTSC) : PART No. J-6090-089-A
HLX-507 (DVD-DL) (PAL) : PART No. J-6090-078-A
HLX-504 (DVD-SL) (NTSC) : PART No. J-6090-088-A
HLX-506 (DVD-SL) (PAL) : PART No. J-6090-077-A
HLX-501 (DVD-DL) (NTSC) : PART No. J-6090-071-A
HLX-505 (DVD-DL) (NTSC) : PART No. J-6090-089-A
HLX-507 (DVD-DL) (PAL) : PART No. J-6090-078-A
Note: Do not use excepting test disc for DVD.
ADJUSTMENT AFTER OPTICAL PICK-UP BLOCK RE-
PLACED
After optical pick-up block is replaced, adjustment is necessary. In
this case, perform “EXECUTING IOP MEASUREMENT” (Refer
to page 23 in TEST MODE) next.
PLACED
After optical pick-up block is replaced, adjustment is necessary. In
this case, perform “EXECUTING IOP MEASUREMENT” (Refer
to page 23 in TEST MODE) next.
RF LEVEL CHECK
+
–
–
DMB17 board
CN105 pin (RFMON)
CN105 pin (GND)
oscilloscope
(DC range)
Procedure :
1. Connect the oscilloscope to CN105 pin
1. Connect the oscilloscope to CN105 pin
6 (RFMON) and
CN105 pin
3 (GND) on the DMB17 board.
2. Press the [I/
1
] button to turn the power on.
3. Insert the test disc and touch the [
Y
] sensor to playback.
4. Confi rm that oscilloscope waveform is as shown in the fi gure
below. (eye pattern)
A good eye pattern means that the diamond shape (
◊) in the
center of the waveform can be clearly distinguished.
VOLT/DIV: 200 mV
TIME/DIV: 500 ns
level:
0.8
± 0.2 Vp-p (DVD)
0.8
± 0.2 Vp-p (CD)
Checking Location:
– DMB17 Board (Component Side) –
6
1
CN105
IC104
IC102
IC101
IC201
HCD-AZ33D
28
FM TUNE LEVEL CHECK
signal
generator
set
Procedure:
1. Turn on the set.
2. Input the following signal from signal generator to FM antenna
1. Turn on the set.
2. Input the following signal from signal generator to FM antenna
input directly.
Carrier frequency : A = 87.5 MHz, B = 98 MHz, C = 108 MHz
Deviation : 75 kHz
Modulation : 1 kHz
ANT input : 35 dBu (EMF)
Modulation : 1 kHz
ANT input : 35 dBu (EMF)
Note: Use 75 ohm coaxial cable to connect signal generator and the set.
You cannot use video cable for checking.
Use signal generator whose output impedance is 75 ohm.
3. Set to FM tuner function and tune A, B and C signals.
4. Confi rm “TUNED” is lit on the display for A, B and C sig-
nals.
When the selected station signal is received in good condition,
“TUNED” is displayed.
TUNER SECTION
Click on the first or last page to see other DHC-AZ33D / HCD-AZ33D service manuals if exist.