Sony DHC-AZ33D / HCD-AZ33D Service Manual ▷ View online
HCD-AZ33D
21
3-20. LEVER (DISC SENSOR)/(DISC STOP)
3-21. GEAR (IDL-C)
chassis (top)
hole
Install the lever (disc stop) so that the both holes
are aligned.
are aligned.
hole
gear (cap)
two claws
two hooks
lever (disc stop)
lever (disc stop)
lever (disc sensor)
PRECAUTION DURING DISC STOP LEVER INSTALLATION
gear (IDL L)
three hooks
two claws
claw
gear (IDL-F)
gear (IDL-C)
gear (IDL-D)
lever (gear loading) assy
HCD-AZ33D
22
SECTION 4
TEST MODE
COLD RESET
The cold reset clears data except DVD data stored in the RAM to
initial conditions. Execute this mode when returning the set to the
customers.
Procedure:
1. Press the [
The cold reset clears data except DVD data stored in the RAM to
initial conditions. Execute this mode when returning the set to the
customers.
Procedure:
1. Press the [
?/1
] button to turn the power on.
2. Press two buttons of [
?/1
], [DISPLAY] and touch the [
x
] sen-
sor simultaneously.
3. The message “COLD RESET” is displayed on the fl uorescent
indicator tube, then become standby mode.
PANEL TEST MODE
This mode is used to check the fl uorescent indicator tube, LED,
model, destination, software version and key.
Procedure:
1. Press two buttons of [EQ EDIT], [DIRECTION] and touch the
This mode is used to check the fl uorescent indicator tube, LED,
model, destination, software version and key.
Procedure:
1. Press two buttons of [EQ EDIT], [DIRECTION] and touch the
[
x
] sensor simultaneously.
2. All LEDs and segments in fl uorescent indicator tube are light-
ed up.
3. When you want to enter the software version display mode,
touch the [
.
-] sensor. The model name is displayed.
4. Each time [
.
-] sensor is touched, the display changes from
destination, MC version, SYS version, UI version, DVD ver-
sion, ST version, TA version, DSP version, TM version, TC
version, MM version, CLA version in this order, and returns to
the model name display.
sion, ST version, TA version, DSP version, TM version, TC
version, MM version, CLA version in this order, and returns to
the model name display.
5. When
[
>
+] sensor is touched while the version numbers
are being displayed except model name and destination, the
date of the software creation appear. When [
date of the software creation appear. When [
>
+] sensor
is touched again, the display returns to the software version
display. When [
display. When [
.
-] sensor is touched while the date of the
software creation is being displayed, the date of the software
creation is displayed in the same order of software version dis-
play.
creation is displayed in the same order of software version dis-
play.
6. Press the [DSGX] button, the key check mode is activated.
7. In the key check mode, the fl uorescent indicator tube displays
7. In the key check mode, the fl uorescent indicator tube displays
“K 0” Each time a button is pressed, “K 0” value increases.
However, once a button has been pressed, it is no longer taken
into account.
However, once a button has been pressed, it is no longer taken
into account.
8. To release from this mode, press three buttons in the same
manner as step 1 or disconnect the power cord.
SHIP MODE
This mode moves the optical pick-up to the position durable to
vibration. Use this mode when returning the set to the customer
after repair.
Procedure:
1. Press the [
This mode moves the optical pick-up to the position durable to
vibration. Use this mode when returning the set to the customer
after repair.
Procedure:
1. Press the [
?/1
] button to turn the power on.
2. Touch the [DVD] sensor to select “DVD”
3. Press the [
3. Press the [
?/1
] button and touch [
bB
] sensor simultaneously.
4. After the “STANDBY” blinking display fi nish, the message
“MECHA LOCK” is displayed on the fl uorescent indicator
tube.
tube.
MEMORY CLEAR MODE
This mode moves clears main microprocessor data stored in the
RAM to initial conditions. Use this mode when returning the set to
the customer after repair.
Procedure:
1. Press the [
This mode moves clears main microprocessor data stored in the
RAM to initial conditions. Use this mode when returning the set to
the customer after repair.
Procedure:
1. Press the [
?/1
] button to turn the power on.
2. Touch the [DVD] sensor to select the “DVD”
3. Press the [PRESET EQ] button and touch two sensors of
3. Press the [PRESET EQ] button and touch two sensors of
[DVD], [
x
] simultaneously.
4. After the “STANDBY” blinking display fi nish, the message
“MECHA LOCK” is displayed on the fl uorescent indicator
tube.
tube.
DISC SLOT LOCK
This mode let you lock the disc slot. When this mode is activated,
the disc will not eject when [
This mode let you lock the disc slot. When this mode is activated,
the disc will not eject when [
Z
] button is pressed. The message
“LOCKED” will be displayed in on the fl uorescent indicator tube.
Procedure:
1. Press the [
Procedure:
1. Press the [
?/1
] button to turn the power on.
2. Touch the [DVD] sensor to select the “DVD”
3. Touch the [
3. Touch the [
x
] sensor and press the [
Z
] button simultaneously
and hold down until “LOCKED” or “UNLOCKED” displayed
on the fl uorescent indicator tube (around 5 seconds).
on the fl uorescent indicator tube (around 5 seconds).
TUNER STEP CHANGE
(Except AEP model)
The step interval of AM channels can be toggled between 9 kHz
and 10 kHz.
Procedure:
1. Press the [
(Except AEP model)
The step interval of AM channels can be toggled between 9 kHz
and 10 kHz.
Procedure:
1. Press the [
?/1
] button to turn the power on.
2. Touch the [TUNER/BAND] sensor to select the “AM”
3. Press the [
3. Press the [
?/1
] button to turn the power off.
4. Touch the. [
.
-] sensor and press [
?/1
] button simultane-
ously. The set power on automatically. The message “AM 9k
Step” or “AM10k Step” displayed on the fl uorescent indicator
tube and thus the channel step is changed.
Step” or “AM10k Step” displayed on the fl uorescent indicator
tube and thus the channel step is changed.
FUNCTION NAME CHANGE
This mode let you change from VIDEO to SAT and vice-versa.
Procedure:
1. Press the [
This mode let you change from VIDEO to SAT and vice-versa.
Procedure:
1. Press the [
?/1
] button to turn the power on.
2. Touch the [VIDEO/SAT] sensor and press [
?/1
] button simul-
taneously. The set power on automatically and the function
will changed to SAT. Do the same procedures again to change
from SAT to VIDEO.
will changed to SAT. Do the same procedures again to change
from SAT to VIDEO.
COLOR SYSTEM CHANGE
(Except AEP model)
This mode let you change the color system of the video output
from PAL to NTSC or vice-versa.
Procedure:
1. Press the [
(Except AEP model)
This mode let you change the color system of the video output
from PAL to NTSC or vice-versa.
Procedure:
1. Press the [
?/1
] button to turn the power on.
2. Touch the [DVD] sensor to select the “DVD”
3. Press the [
3. Press the [
?/1
] button to turn the power off.
4. Touch the [
X
] sensor and press [
?/1
] button simultaneously.
5. The message “COLOR PAL” or “COLOR NTSC” will be dis-
played on the fl uorescent indicator tube.
HCD-AZ33D
23
TEST DISC LIST
Use the following test disc on test mode.
YEDS-18 (CD)
Use the following test disc on test mode.
YEDS-18 (CD)
: PART No. 3-702-101-01
PATD-012 (CD)
: PART No. 4-225-203-01
HLX-503 (DVD-SL) (NTSC) : PART No. J-6090-069-A
HLX-504 (DVD-SL) (NTSC) : PART No. J-6090-088-A
HLX-506 (DVD-SL) (PAL)
HLX-504 (DVD-SL) (NTSC) : PART No. J-6090-088-A
HLX-506 (DVD-SL) (PAL)
: PART No. J-6090-077-A
HLX-501 (DVD-DL) (NTSC) : PART No. J-6090-071-A
HLX-505 (DVD-DL) (NTSC) : PART No. J-6090-089-A
HLX-507 (DVD-DL) (PAL)
HLX-505 (DVD-DL) (NTSC) : PART No. J-6090-089-A
HLX-507 (DVD-DL) (PAL)
: PART No. J-6090-078-A
Note: Do not use excepting test disc for DVD.
1. DVD SERVICE MODE GENERAL DESCRIPTION
This mode let you make diagnosis and adjustment easily by using
the remote commander and the TV screen. The instructions, diag-
nostic results, etc. are given on the on-screen display.
This mode let you make diagnosis and adjustment easily by using
the remote commander and the TV screen. The instructions, diag-
nostic results, etc. are given on the on-screen display.
2. ENTERING DVD SERVICE MODE
Procedure:
1. Press the [
Procedure:
1. Press the [
?/1
] button to turn on the system.
2. Touch the [DVD] sensor to select the “DVD”
3. Press the [
3. Press the [
Z
] button and touch two sensors of [
x
] and
[VOLUME +] simultaneously.
4. The message “SERVICE IN” appears on the fl uorescent in-
dicator tube and top menu of the Remocon Diagnosis Menu
appears on the on-screen display on the TV screen as follows.
The model name, IF-con version and Syscon version are dis-
played at the bottom of the on-screen display.
appears on the on-screen display on the TV screen as follows.
The model name, IF-con version and Syscon version are dis-
played at the bottom of the on-screen display.
Drive Manual Operation
0. External Chip Check
1. Servo Parameter Check
2. Drive Manual Operation
3. Emergency History
4. Version Information
Model Name
:ARX2DM_xx
IF-con:Ver.xx.xx(xxxx)
Syscon:Ver.x.xxx
5. To execute each function, press its number by using numeric
button on the remote commander.
6. To release from this mode, press the [
?/1
] button to turn off
the system.
DVD SECTION
3. EXECUTING IOP MEASUREMENT
In order to execute IOP measurement, the following standard pro-
cedures must be followed.
Procedure:
1. From the top menu of Remocon Diagnosis Menu, select “2.
In order to execute IOP measurement, the following standard pro-
cedures must be followed.
Procedure:
1. From the top menu of Remocon Diagnosis Menu, select “2.
Drive Manual Operation” by pressing the [2] button on the
remote commander. The following screen appears on the on-
screen display
remote commander. The following screen appears on the on-
screen display
Remocon Diagnosis Menu
1. Servo Control
2. Track/Layer Jump
3. Manual Adjustment
4. Tray Aging Mode
5. MIRR time Adjust
0. Return to Top Menu
2. Select “3. Manual Adjustment” by pressing the [3] button on
the remote commander. The following screen appears on the
on-screen display.
on-screen display.
Manual Adjust
1. Track Balance Adjust:
2. Track Gain Adjust:
3. Focus Balance Adjust:
4. Focus Gain Adjust:
5. Eq Boost Adjust:
6. Iop:
7. TRV. Level:
8. S curve(FE) Level:
9. RFL(PI) Level:
0. MIRR Time:
V v Change Value
[RETURN]Return to previous menu
3. Select “6. Iop:” by pressing [6] button on the remote com-
mander.
4. Wait until a hexadecimal number appear in the on-screen dis-
play as below.
Manual Adjust
1. Track Balance Adjust:
2. Track Gain Adjust:
3. Focus Balance Adjust:
4. Focus Gain Adjust:
5. Eq Boost Adjust:
6. Iop: 5D
7. TRV. Level:
8. S curve(FE) Level:
9. RFL(PI) Level:
0. MIRR Time:
V v Change Value
[RETURN]Return to previous menu
HCD-AZ33D
24
5. Convert data from hexadecimal to decimal by using conver-
sion table.
6. Please
fi nd the label on the rear of BU (Base Unit).
The default IOP value is written in the label.
7. Subtract between these two values.
8. If the value is smaller than 93 (decimal), then it is OK. How-
7. Subtract between these two values.
8. If the value is smaller than 93 (decimal), then it is OK. How-
ever if the value is higher than 93, then BU (base unit) is defec-
tive and need to be change.
tive and need to be change.
9. Press the [
O
RETURN] button on the remote commander to
return to previous menu.
10. Press the [0] button on the remote commander to return to the
top menu of Remocon Diagnosis Menu.
11. Press the [
?/1
] button to turn off the system.
4. CHECKING EMERGENCY HISTORY
To check the emergency history, please follow the following pro-
cedure.
Procedure:
1. From the top menu of Remocon Diagnosis Menu, select “3.
To check the emergency history, please follow the following pro-
cedure.
Procedure:
1. From the top menu of Remocon Diagnosis Menu, select “3.
Emergency History” by pressing the [3] button on the remote
commander. The following screen appears on the on-screen
display.
commander. The following screen appears on the on-screen
display.
Emg. History Check
Laser Hours CD 999h 59min
DVD 999h 59min
01. 01 05 04 04 00 92 46 00
00 00 00 00 00 00 23 45
02. 02 02 01 01 00 A9 4B 00
00 00 00 00 00 00 23 45
[Next]Next page [Prev]Prev page
[0]Return to Top Menu
2. You can check the total time when the laser is turned on during
playback of DVD and CD from the above menu. The maxi-
mum time, which can be displayed are 999h 59min.
mum time, which can be displayed are 999h 59min.
3. You can check the error code of latest 10 emergency history
from the above menu. To view the previous or next page of
emergency history, press the [
emergency history, press the [
.
] or [
>
] button on the re-
mote commander. The error code consists of three kinds of
error codes.
error codes.
A. Error code
Example of Error code
01. 01 05 04 04 00 92 46 00
00 00 00 00 00 00 23 45
The meaning of error code is as below:
01: Communication error (No reply from syscon)
02: Syscon hung up
03: Power OFF request when syscon hung up
19: Thermal shutdown
24: MoveSledHome error
25: Mechanical move error (5 changer)
26: Mechanical move stack error
30: DC motor adjustment error
31: DPD offset adjustment error
32: TE balance adjustment error
33. TE sensor adjustment error
34. TE loop gain adjustment error
35. FE loop gain adjustment error
01: Communication error (No reply from syscon)
02: Syscon hung up
03: Power OFF request when syscon hung up
19: Thermal shutdown
24: MoveSledHome error
25: Mechanical move error (5 changer)
26: Mechanical move stack error
30: DC motor adjustment error
31: DPD offset adjustment error
32: TE balance adjustment error
33. TE sensor adjustment error
34. TE loop gain adjustment error
35. FE loop gain adjustment error
36. Bad jitter after adjustment
40. Focus NG
42. Focus layer jump NG
52. Open kick spindle error
51: Spindle stop error
60: Focus on error
61: Seek fail error
62: Read Q data/ID error
70: Lead in data read fail
71: TOC read time out (CD)
80: Can’t buffering
81: Unknown media type
40. Focus NG
42. Focus layer jump NG
52. Open kick spindle error
51: Spindle stop error
60: Focus on error
61: Seek fail error
62: Read Q data/ID error
70: Lead in data read fail
71: TOC read time out (CD)
80: Can’t buffering
81: Unknown media type
B. Parameter of error code
This is the detail of error code.
This is the detail of error code.
Example of Error code
01. 01 05 04 04 00 92 46 00
00 00 00 00 00 00 23 45
C. Time of error code
This is the laser time when an error occurred.
This is the laser time when an error occurred.
Example of Error code
01. 01 05 04 04 00 92 46 00
00 00 00 00 00 00 23 45
To Clear the Laser Hour
Press the [ DISPLAY] button on the remote commander and
then press the [CLEAR] button on the remote commander. The
data for both CD and DVD data are reset.
Press the [ DISPLAY] button on the remote commander and
then press the [CLEAR] button on the remote commander. The
data for both CD and DVD data are reset.
Emg. History Check
Laser Hours CD 0h 0min
DVD 0h 0min
01. 01 05 04 04 00 92 46 00
00 00 00 00 00 00 23 45
02. 02 02 01 01 00 A9 4B 00
00 00 00 00 00 00 23 45
[Next]Next page [Prev]Prev page
[0]Return to Top Menu
To Clear the Emergency History
Press the [DVD TOP MENU] button on the remote commander
and then press the [CLEAR] button on the remote commander. The
error code for all emergency history would be reset.
Press the [DVD TOP MENU] button on the remote commander
and then press the [CLEAR] button on the remote commander. The
error code for all emergency history would be reset.
Emg. History Check
Laser Hours CD 999h 59min
DVD 999h 59min
01. 00 00 00 00 00 00 00 00
00 00 00 00 00 00 00 00
02. 00 00 00 00 00 00 00 00
00 00 00 00 00 00 00 00
[Next]Next page [Prev]Prev page
[0]Return to Top Menu
Ver. 1.1
Click on the first or last page to see other DHC-AZ33D / HCD-AZ33D service manuals if exist.