Sony DAV-HDX900W / HCD-HDX900W Service Manual ▷ View online
5
HCD-HDX900W
NOTES ON HANDLING THE OPTICAL PICK-UP
BLOCK OR BASE UNIT
BLOCK OR BASE UNIT
The laser diode in the optical pick-up block may suffer electrostatic
break-down because of the potential difference generated by the
charged electrostatic load, etc. on clothing and the human body.
During repair, pay attention to electrostatic break-down and also
use the procedure in the printed matter which is included in the
repair parts.
The flexible board is easily damaged and should be handled with
care.
break-down because of the potential difference generated by the
charged electrostatic load, etc. on clothing and the human body.
During repair, pay attention to electrostatic break-down and also
use the procedure in the printed matter which is included in the
repair parts.
The flexible board is easily damaged and should be handled with
care.
NOTES ON LASER DIODE EMISSION CHECK
The laser beam on this model is concentrated so as to be focused on
the disc reflective surface by the objective lens in the optical pick-
up block. Therefore, when checking the laser diode emission,
observe from more than 30 cm away from the objective lens.
the disc reflective surface by the objective lens in the optical pick-
up block. Therefore, when checking the laser diode emission,
observe from more than 30 cm away from the objective lens.
UNLEADED SOLDER
Boards requiring use of unleaded solder are printed with the lead-
free mark (LF) indicating the solder contains no lead.
(Caution: Some printed circuit boards may not come printed with
free mark (LF) indicating the solder contains no lead.
(Caution: Some printed circuit boards may not come printed with
the lead free mark due to their particular size)
: LEAD FREE MARK
Unleaded solder has the following characteristics.
• Unleaded solder melts at a temperature about 40 °C higher
than ordinary solder.
Ordinary soldering irons can be used but the iron tip has to be
applied to the solder joint for a slightly longer time.
Soldering irons using a temperature regulator should be set to
about 350
Ordinary soldering irons can be used but the iron tip has to be
applied to the solder joint for a slightly longer time.
Soldering irons using a temperature regulator should be set to
about 350
°C.
Caution: The printed pattern (copper foil) may peel away if
the heated tip is applied for too long, so be careful!
• Strong viscosity
Unleaded solder is more viscou-s (sticky, less prone to flow)
than ordinary solder so use caution not to let solder bridges
occur such as on IC pins, etc.
than ordinary solder so use caution not to let solder bridges
occur such as on IC pins, etc.
• Usable with ordinary solder
It is best to use only unleaded solder but unleaded solder may
also be added to ordinary solder.
also be added to ordinary solder.
RELEASING THE TRAY LOCK
The disc tray lock function for the antitheft of an demonstration
disc in the store is equipped.
disc in the store is equipped.
Releasing Procedure :
1. Press the
I
/1
button to turn on the system.
2. Press the
FUNCTION
button repeatedly to select “DVD”.
3. While pressing the
x
button, press the
A
button until
“UNLOCKED” displayed on the fluorescent indicator tube
(around 5 seconds).
(around 5 seconds).
Note:
When “LOCKED” is displayed, the tray lock is not released by turning
power on/off with the
power on/off with the
I/
1
button.
RELEASING THE DEMO PLAY LOCK
Releasing Procedure :
1. Press the
I
/1
button to turn on the system.
2. Press the
FUNCTION
button repeatedly to select “DVD”.
3. While pressing the
x
button, press the
H
button until
“DEMO OFF” displayed on the fluorescent indicator tube
(around 5 seconds).
(around 5 seconds).
Note:
When “DEMO PLAY” is displayed, the set is not possible to turn off
the system.
the system.
SECTION 1
SERVICING NOTES
NOTE OF REPLACING THE EEPROM (IC1103) ON
THE MAIN BOARD
THE MAIN BOARD
EEPROM (IC1103) on the MAIN board cannot exchange with
single. When EEPROM (IC1103) on the MAIN board is damaged,
exchange the entire mounted board.
single. When EEPROM (IC1103) on the MAIN board is damaged,
exchange the entire mounted board.
6
HCD-HDX900W
• The Control Menu items may vary depending
on the area.
• “DVD” may be used as a general term for
DVD VIDEOs, DVD+RWs/DVD+Rs, and
DVD-RWs/DVD-Rs.
DVD-RWs/DVD-Rs.
• Measurements are expressed in feet (ft) for
North American models.
• The following symbols are used in this
manual.
* MP3 (MPEG1 Audio Layer 3) is a standard format
defined by ISO/MPEG which compresses audio
data.
data.
“DVD-RW,” “DVD +RW,” “DV D+R,”
“DVD VIDEO,” and the “CD” logos are trademarks.
“DVD VIDEO,” and the “CD” logos are trademarks.
Note about CDs/DVDs
The system can play CD-ROMs/CD-Rs/CD-
RWs recorded in the following formats:
RWs recorded in the following formats:
– audio CD format
– VIDEO CD format
– MP3 audio tracks and JPEG image files of
format conforming to ISO 9660 Level 1/
Level 2, or its extended format, Joliet
Level 2, or its extended format, Joliet
Symbol
Meaning
Functions available for DVD
VIDEOs, DVD-Rs/DVD-RWs in
video mode, and DVD+Rs/
DVD+RWs
VIDEOs, DVD-Rs/DVD-RWs in
video mode, and DVD+Rs/
DVD+RWs
Functions available for DVD-Rs/
DVD-RWs in VR (Video
Recording) mode
DVD-RWs in VR (Video
Recording) mode
Functions available for VIDEO
CDs (including Super VCDs or CD-
Rs/CD-RWs in video CD format or
Super VCD format)
CDs (including Super VCDs or CD-
Rs/CD-RWs in video CD format or
Super VCD format)
Functions available for music CDs
or CD-Rs/CD-RWs in music CD
format
or CD-Rs/CD-RWs in music CD
format
Functions available for DATA CDs
(CD-ROMs/CD-Rs/CD-RWs)
containing MP3* audio tracks and
JPEG image files
(CD-ROMs/CD-Rs/CD-RWs)
containing MP3* audio tracks and
JPEG image files
Functions available for DATA
DVDs (DVD-ROMs/DVD-Rs/
DVD-RWs /DVD+Rs/DVD+RWs)
containing MP3* audio tracks and
JPEG image files
DVDs (DVD-ROMs/DVD-Rs/
DVD-RWs /DVD+Rs/DVD+RWs)
containing MP3* audio tracks and
JPEG image files
CD-RW/CD-R
(audio data)
(MP3 files)
(JPEG files)
(audio data)
(MP3 files)
(JPEG files)
This System Can Play the
Following Discs
Following Discs
Format of
discs
discs
Disc logo
DVD V IDEO
DVD-RW/
DVD-R
DVD-R
DVD+RW/
DVD+R
DVD+R
VIDEO CD
(Ver. 1.1 and
2.0 discs)/
Audio CD
(Ver. 1.1 and
2.0 discs)/
Audio CD
The system can play DVD-ROMs/DVD+RWs/
DVD-RWs/DVD+Rs/DVD-Rs recorded in the
following formats:
DVD-RWs/DVD+Rs/DVD-Rs recorded in the
following formats:
– MP3 audio tracks and JPEG image files of
format conforming to UDF (Universal Disk
Format)
Format)
Example of discs that the
system cannot play
system cannot play
The system cannot play the following discs:
• CD-ROMs recorded in PHOTO CD format
• Data part of CD-Extras
• DVD Audios
• Super Audio CD
• DATA DVDs that do not contain MP3 audio
tracks or JPEG image files
• DVD-RAMs
Also, the system cannot play the following
discs:
discs:
• A DVD VIDEO with a different region code
• A disc that has a non-standard shape (e.g.,
card, heart)
• A disc with paper or stickers on it
• A disc that has the adhesive of cellophane tape
or a sticker still left on it
Notes about CD-R/CD-RW/DVD-R/
DVD-RW/DVD+R/DVD+RW
DVD-RW/DVD+R/DVD+RW
In some cases, CD-R/CD-RW/DVD-R/DVD-
RW/DVD+R/DVD+RW cannot be played on
this system due to the recording quality or
physical condition of the disc, or the
characteristics of the recording device and
authoring software.
The disc will not play if it has not been correctly
finalized. For more information, see the
operating instructions for the recording device.
Note that some playback functions may not
work with some DVD+RWs/DVD+Rs, even if
they have been correctly finalized. In this case,
view the disc by normal playback. Also some
DAT A CDs/DAT A DVDs created in Packet
Write format cannot be played.
RW/DVD+R/DVD+RW cannot be played on
this system due to the recording quality or
physical condition of the disc, or the
characteristics of the recording device and
authoring software.
The disc will not play if it has not been correctly
finalized. For more information, see the
operating instructions for the recording device.
Note that some playback functions may not
work with some DVD+RWs/DVD+Rs, even if
they have been correctly finalized. In this case,
view the disc by normal playback. Also some
DAT A CDs/DAT A DVDs created in Packet
Write format cannot be played.
Music discs encoded with
copyright protection
technologies
copyright protection
technologies
This product is designed to play back discs that
conform to the Compact Disc (CD) standard.
Recently, various music discs encoded with
copyright protection technologies are marketed
by some record companies. Please be aware that
among those discs, there are some that do not
conform to the CD standard and may not be
playable by this product.
conform to the Compact Disc (CD) standard.
Recently, various music discs encoded with
copyright protection technologies are marketed
by some record companies. Please be aware that
among those discs, there are some that do not
conform to the CD standard and may not be
playable by this product.
Note on DualDiscs
A DualDisc is a two sided disc product which
mates DVD recorded material on one side with
digital audio material on the other side.
However, since the audio material side does not
conform to the Compact Disc (CD) standard,
playback on this product is not guaranteed.
mates DVD recorded material on one side with
digital audio material on the other side.
However, since the audio material side does not
conform to the Compact Disc (CD) standard,
playback on this product is not guaranteed.
About Multi Session CD
• This system can play Multi Session CDs when
an MP3 audio track is contained in the first
session. Any subsequent MP3 audio tracks
recorded in later sessions can also be played
back.
session. Any subsequent MP3 audio tracks
recorded in later sessions can also be played
back.
• This system can play Multi Session CDs when
a JPEG image file is contained in the first
session. Any subsequent JPEG image files
recorded in later sessions can also be played
back.
session. Any subsequent JPEG image files
recorded in later sessions can also be played
back.
• If audio tracks and images in music CD format
or video CD format are recorded in the first
session, only the first session will be played
back.
session, only the first session will be played
back.
Region code
You r system has a region code printed on the
rear of the unit and will only play DVDs labeled
with the same region code.
rear of the unit and will only play DVDs labeled
with the same region code.
DVD VIDEOs labeled
will also play on this
system.
If you try to play any other DVD VIDEO, the
message [Playback prohibited by area
limitations.] will appear on the TV screen.
Depending on the DVD VIDEO, no region code
indication may be given even though playing the
DVD VIDEO is prohibited by area restrictions.
If you try to play any other DVD VIDEO, the
message [Playback prohibited by area
limitations.] will appear on the TV screen.
Depending on the DVD VIDEO, no region code
indication may be given even though playing the
DVD VIDEO is prohibited by area restrictions.
Note about playback
operations of DVDs and
VIDEO CDs
operations of DVDs and
VIDEO CDs
Some playback operations of DVDs and VIDEO
CDs may be intentionally set by software
producers. Since this system plays DVDs and
VIDEO CDs according to the disc contents the
software producers designed, some playback
features may not be available. Be sure to read the
operating instructions supplied with the DVDs
or VIDEO CDs.
CDs may be intentionally set by software
producers. Since this system plays DVDs and
VIDEO CDs according to the disc contents the
software producers designed, some playback
features may not be available. Be sure to read the
operating instructions supplied with the DVDs
or VIDEO CDs.
ALL
7
HCD-HDX900W
CCX, CHOPPER, EN, LED, MAIN, PW-SW AND
SPEAKER BOARDS DISCRIMINATION
SPEAKER BOARDS DISCRIMINATION
In this set, the CCX, CHOPPER, EN, LED, MAIN, PW-SW and
SPEAKER boards have been changed in the midway of production.
Repair after distinguishing each type set to doing the repair referring
to the following.
SPEAKER boards have been changed in the midway of production.
Repair after distinguishing each type set to doing the repair referring
to the following.
• DISCRIMINATION
SUFFIX-11
: 1-872-103-11
SUFFIX-12
: 1-872-103-12
– MAIN BOARD (Component Side) –
SUFFIX-11
: 1-872-121-11
SUFFIX-12
: 1-872-121-12
– CCX BOARD (Component Side) –
SUFFIX-11/-12 : 1-782-114-11, 12
SUFFIX-13
SUFFIX-13
: 1-782-114-13
SUFFIX-11/-12 : 1-872-104-11, 12
SUFFIX-13
SUFFIX-13
: 1-872-104-13
SUFFIX-11/-12 : 1-872-115-11, 12
SUFFIX-13
SUFFIX-13
: 1-872-115-13
SUFFIX-11/-12 : 1-872-116-11, 12
SUFFIX-13
SUFFIX-13
: 1-872-116-13
SUFFIX-11/-12 : 1-872-292-11, 12
SUFFIX-13
SUFFIX-13
: 1-872-292-13
– EN BOARD –
(Component Side)
(Component Side)
– LED BOARD –
(Component Side)
(Component Side)
– SPEAKER BOARD (Component Side) –
– PW-SW BOARD –
(Component Side)
(Component Side)
– CHOPPER BOARD (Component Side) –
8
HCD-HDX900W
HOW TO IDENTIFY OPTICAL PICK-UP BLOCK
Printed of KHM-310CAB or KHM-313CAB.
Note:
There are two kinds of OPTICAL PICK-UP BLOCK in this set.
When replacing the OPTICAL PICK-UP BLOCK, make sure which
OPTICAL PICK-UP BLOCK it is following the “How to Identify”
in the figure shown below.
When replacing the OPTICAL PICK-UP BLOCK, make sure which
OPTICAL PICK-UP BLOCK it is following the “How to Identify”
in the figure shown below.
OPTICAL PICK-UP BLOCK
HOW TO OPEN THE TRAY WHEN POWER SWITCH TURN OFF
gear (BU1)
Turn gear (BU1) from a hole at the bottom,
and pull out a tray.
and pull out a tray.
tray
Click on the first or last page to see other DAV-HDX900W / HCD-HDX900W service manuals if exist.