DOWNLOAD Sony DAV-HDX900W / HCD-HDX900W Service Manual ↓ Size: 8.11 MB | Pages: 127 in PDF or view online for FREE

21

2

 stocker section 

1

 Rotate the gear (SS3) in the

     direction of the arrow.

5

 two screws

     (PTPWH2.6 

×

 8)

6

 two cams

     (stocker)

8

 cam

     (stocker)

cam (stocker)

cam (stocker)

cam (stocker)

hole

gear
 (stocker 2)

gear
 (stocker 2)

gear
 (stocker 2)

gear (stocker 3)

2

 tension spring (SW)

4

 lever (SW)

1

 floating screw

     (PTPWH M2.6)

7

 screw

     (PTPWH2.6 

×

 8)

3

 hook

Before installing the cams (stocker), fix the gear (stocker 3) in
the manner so that the hole of the gear (stocker 3) should be
aligned with the hole of the chassis located beneath 
the gear (stocker 3). Be sure to install the cams (stocker) in 
such a way that the grooves of the cams (stocker) face 
the direction of the arrows.

22

1

 step tapping screw

     (PWH 2 

×

 6)

2

 gear (stocker 3)

gear (stocker 3)
(reverse-side)

rotary encoder
 (ST U/D encoder)

Be sure to align the rib of the gear (stocker 3) with the groove
of the rotary encoder.

groove

rib

1

 three screws

     (BTTP M2.6)

2

 rotary encoder (MD)

rotary encoder (MD)

gear (BU1)

cam (BU)

Slide the cam (BU) in the direction of the arrow so that the mark
of the gear (BU1) can be seen. Engage the gears while aligning 
the mark of the gear (BU1) with the protruding part of the 
rotary encoder.

protruding part

mark

23

2

 screw

     (PTPWH2.6 

×

 8)

4

 screw

     (PTPWH2.6 

×

 8)

6

 screw

     (PTPWH2.6 

×

 8)

3

 pulley (BU)

5

 gear (BU1)

7

 gear (BU2)

1

 belt (sub tray)

gear (BU2)

cam (BU)

Before re-assembling, slide the cam (BU) in the direction of 
the arrow. 
Assemble the gear (BU2) in such a manner that the groove
of the cam (BU) is aligned with the rib of the gear (BU2).

rib

groove

24

Incorrect operations may be performed if the test mode is not entered
properly. In this case, press the

?

/

1

button to turn the power off,

and retry to enter the test mode.

The cold reset clears all data including preset data stored in the
RAM to initial conditions. Execute this mode when returning the
set to the customers.
Procedure:

1. Press the

?

/

1

button to turn the power on.

2. Press three buttons 

x

 , 

A

 and

?

/

1

simultaneously.

3. When this button is operated, display as “COLD RESET” for

a while and all of the settings are reset.

This mode is used to check the software version, FL, LED and KEY.

1. Press the

?

/

1

button to turn the power on.

2. Press three buttons 

X

 , 

.

 and 

A

 simultaneously.

3. When the display test mode is activated, all segments are turned

on.

4. To exit from this mode, press three buttons 

X

  , 

.

  and 

A

simultaneously.

1. When the display test mode is activated, press the 

.

 button

and “DC9W” is displayed, the version test mode is activated.

2. Whenever the 

.

 button is pressed, the display changes in

order of “DC9W” 

→

 “NA” (destination) 

→

 MC 

→

 SYS 

→

UI 

→

 DVD 

→

 CDMA 

→

 CDMB 

→

 ST 

→

 TA 

→

 DSP 

→

TM 

→

 XM 

→

 CLA 

→

 CEC 

→

 “DC9W” (model name).

3. Press the 

>

 button and the date of the software production is

displayed.

4. Press the 

>

 button again and the version is displayed.

5. To exit from this mode, press three buttons 

X

  , 

.

  and 

A

simultaneously.

1. When the display test mode is activated, press the 

H

 button,

to select the key test mode.

2. To enter the KEY test mode, the fluorescent indicator displays

“K0 V0”. Each time an another button is pressed, “KEY” value
increases. However, once a button is pressed, it is no longer
taken into account. When all keys are pressed correctly, “K13
V0” is displayed.

3. When the [VOLUME] dial is turned in the direction of (+), “V0”

is changed to “V1”, then ... “V9”.

When the [VOLUME] dial is turned in the direction of (–), “V0”

is changed to “V9”, then ... “V1”.

4. To exit from this mode, press three buttons 

X

  , 

.

  and 

A

simultaneously.

The disc tray lock function for the antitheft of an demonstration
disc in the store is equipped.
Setting Procedure :

1. Press the

I

/1

button to turn the set on.

2. Press the [FUNCTION] button to set DVD function.
3. Insert a disc.
4. Press the 

x

 button and the 

A

 button simultaneously for five

seconds.

5. The message “LOCKED” is displayed and the tray is locked.

1. Press the 

x

 button and the 

A

 button simultaneously for five

seconds again.

2. The message “UNLOCKED” is displayed and the tray is

unlocked.

When “LOCKED” is displayed, the tray lock is not released by turning
power on/off with the

?

1

button.

Use this mode when returning the set to the customer after repair.
Procedure:

1. Press the

?

/

1

button to turn the set on.

2. Press the [FUNCTION] button to set the function “DVD”.
3. Remove all discs, and then press two buttons 

H

 and

?

/

1

simultaneously.

4. After a message “MECHA LOCK” is displayed on the

fluorescent indicator tube, pull out the AC plug.

5. To exit from this mode, press the

?

/

1

button to turn the set

on.

A step of AM channels can be changed over between 9 kHz and 10
kHz.
Procedure:

1. Press the

?

/

1

button to turn the set ON.

2. Press the [FUNCTION]  button to set the function “TUNER

AM”.

3. Press the

?

/

1

button to turn the set OFF.

4. Press two buttons 

>

 and

?

/

1

simultaneously, and the display

of fluorescent indicator tube changes to “AM 9k STEP” or
“AM 10k STEP”, and thus the channel step is changed over.

This mode moves the optical pick-up to the position durable to
vibration and clears all data including preset data stored in the RAM
to initial conditions. Use this mode when returning the set to the
customer after repair.
Procedure:

1. Press the

?

/

1

button to turn the power on.

2. Press the [FUNCTION] button to set the function “DVD”.
3. Remove all discs, and then press three buttons 

> 

, 

A

 and

?

/

1

simultaneously.

4. After the “STANDBY” blinking display finishes, the message

“MECHA LOCK” is displayed on the fluorescent indicator
tube disconnect the AC power plug, then the ship mode is set.

1. Press the

?

/

1

button to turn the power on.

2. Insert ECM-AC2 supplied as an accessory into the AUDIO

IN/A.CAL MIC jack.

3. While pressing the 

X

 and 

A

 buttons simultaneously, turn the

[VOLUME] dial in the direction of (+).

4. The state of jack is displayed in the fluorescent indicator tube.

NON : Not detected
ST : STEREO
MONO : MONO

It is a mode to release the demonstration reproduct by the dedicated
demonstration disc.
Procedure:

1. During playback the DEMO disc, press the 

x

 and 

H

 buttons

for five seconds simultaneously.

2. The message “DEMO OFF” is displayed, a mode to reproduct

the demonstration is released.