DOWNLOAD Sony DAV-FR10W / HCD-FR10W Service Manual ↓ Size: 11.8 MB | Pages: 127 in PDF or view online for FREE

Model
DAV-FR10W HCD-FR10W
Pages
127
Size
11.8 MB
Type
PDF
Document
Service Manual
Brand
Device
Audio
File
dav-fr10w-hcd-fr10w.pdf
Date
PREV: Sony SA-TS22W Service Manual

Sony DAV-FR10W / HCD-FR10W Service Manual ▷ View online

17
HCD-FR10W
SECTION 4
ASSEMBLY
• This is can be assemble according to the following sequence.
4-1. HOW TO INSTALL THE CAM (EJECT LOCK)
mark
cam (BU U/D)
cam (eject lock)
– bottom view • front –
gear (eject lock)
1
Rotate the cam (BU U/D) fully in the direction of arrow.
2
Engage the gear (eject lock) and the gear of the cam (eject lock)
aligning the mark with the center of the gear (eject lock).
4-2. HOW TO INSTALL THE CAM (GEAR)
boss
cam (gear)
mark
cam (BU U/D)
– bottom view • front –
1
Check that the cam (BU U/D) can not be rotated in the direction of arrow.
2
Align the mark on the cam (gear) with the boss as shown in the figure
and install the cam (gear).
18
HCD-FR10W
4-3. HOW TO INSTALL THE GEAR (MODE 2)
– bottom view • front –
gear
(mode 2)
rotary encoder
(S701)
cam (BU U/D)
mark
projection
chassis
1
Align the mark on the rotary encoder (S701) with the projection of  the assy.
2
Check that the cam (BU U/D) can not be rotated in the direction of arrow.
3
Install the gear (mode 2).
4-4. HOW TO INSTALL THE GEAR (MODE CAM)
mark 
B
slider (mode cam) assy
shaft
mark 
A
mark 
D
gear (mode cam)
cam (gear)
mark 
C
1
Slide the shaft in the direction of arrow.
2
Align mark 
A
 on the gear (mode cam) with mark 
B
 on the slider (mode cam) assy, 
then install the gear (mode cam).
3
Check that mark 
C
 on the gear (mode cam) is in alignment with mark 
D
 on the cam (gear).
– bottom view • front –
19
HCD-FR10W
4-5. HOW TO INSTALL THE ROTARY ENCODER (S702), GEAR (STOCKER COMMUNICATION)
2
five solders
6
two gears
(stocker communication)
4
gear
(stocker communication)
RELAY board
7
two screws 
(PTPWH2.6
 
×
 8)
5
screw 
(PTPWH2.6
 
×
 8)
3
screw 
(PWH2
 
×
 6)
rotary encoder
(S702)
gear
(stocker 
communication)
– rear –
1
rotary encoder
(S702)
Engage the rotary encoder (S702)
and the gear (stocker communication)
as shown below in the figure.
20
HCD-FR10W
4-6. HOW TO INSTALL THE CAM (STOCKER U/D)
2
two cams 
(stocker U/D)
2
cam (stocker U/D)
3
two screws 
(PTPWH2.6
 
×
 8)
3
screw 
(PTPWH2.6
 
×
 8)
rotary encoder
(S702)
hole
gear
(stocker communication)
– rear –
screw
1
Position the hole on the gear 
(stocker communication) on the
screw of the rotary encoder (S702).
To install three cams (stocker U/D), align each groove
of the cam (stocker U/D) with each 
f
 mark on the 
chassis as shown in the figure.
 
f
 mark 
 
f
 mark 
 
f
 mark 
cam (stocker U/D)
cam (stocker U/D)
cam (stocker U/D)
Page of 127
Display

Click on the first or last page to see other DAV-FR10W / HCD-FR10W service manuals if exist.

RANDOM: