Sony DAV-FR10W / HCD-FR10W Service Manual ▷ View online
21
HCD-FR10W
4-7. HOW TO INSTALL THE STOCKER ASSY
1
Fit three shafts of the stocker assy in respective slits
of the cams (stocker U/D).
of the cams (stocker U/D).
cam (stocker U/D)
cam (stocker U/D)
cam (stocker U/D)
cam (stocker U/D)
shaft
shaft
shaft
stocker assy
cam (stocker U/D)
Note: For the location of slits of the cams (stocker U/D),
see 4-6. HOW TO INSTALL CAM (STOCKER U/D).
2
Making sure that three shafts of the stocker assy fit in
respective slits of the cams (stocker U/D), rotate the
pulley (stocker) in the direction of arrow
respective slits of the cams (stocker U/D), rotate the
pulley (stocker) in the direction of arrow
A
by hand to
store the stocker assy.
A
pulley (stocker)
pulley (stocker)
stocker assy
22
HCD-FR10W
A
A
A
A
A
A
1
As shown in the following figure, adjust the portion
A
of each slider to the boss with the
slider-1 to 5 (L) and the slider-1 to 5 (R) pushed in the arrow directions respectively (see Fig. 1).
2
Paying attention to the up/down direction of the pinion (slider) (see Fig. 2), install each pinion (slider)
so that the portion
so that the portion
B
of each pinion (slider) meshes with the portion
A
of each slider (see Fig. 3).
Note: Push in the pinion (slider) until the claw of the boss comes out above the pinion (slider) to lock.
pinion (slider)
pinion (slider)
pinion (slider)
pinion (slider)
pinion (slider)
pinion (slider)
pinion (slider) portion
B
slider portion
A
slider portion
A
boss
boss
boss
slider-5 (L)
slider-5 (R)
slider-4 (L)
slider-4 (R)
slider-3 (L)
slider-3 (R)
slider-2 (L)
slider-2 (R)
slider-1 (L)
slider-1 (R)
(Fig. 1)
(Fig. 2)
(Fig. 3)
A
A
A
A
boss
boss
boss
boss
claw
claw
pinion (slider) portion
B
4-8. PHASE ADJUSTMENT BETWEEN PINIONS (SLIDER) AND SLIDER-1 TO 5 (L/R)
23
HCD-FR10W
SECTION 5
TEST MODE
[Version Display Mode]
*
The software version is displayed.
Procedure:
1. Press three buttons of [VOLUME -], [VOLUME +] and A si-
multaneously for two seconds.
2. The message “VERSION” is displayed. The version display
mode is activated.
3. Press the > button. “IF ***” is displayed.
4. Each time the > button is pressed, the display changes in
4. Each time the > button is pressed, the display changes in
the order of DVD, AREA, VERSION and IF.
5. To exit from this mode, press the ?/1 button.
[Key Test Mode]
*
Button check
Procedure:
1. Press three buttons of [VOLUME -], [VOLUME +] and [FUNC-
TION] simultaneously.
2. The message “KEY NUM 0” is displayed and “0” blinks.
3. Each time a button is pressed, “KEY NUM 0” value increases.
3. Each time a button is pressed, “KEY NUM 0” value increases.
However, once a button is pressed, it is no longer taken into
account.
account.
4. When all buttons are pressed, “KEY NUM 9” appears and the
number blinking is stopped.
5. To exit from this mode, disconnect the power cord.
[Display Test Mode]
Procedure:
1. Press three buttons of [VOLUME -], . and A simulta-
neously.
2. All segments are turned on.
3. When the > button is pressed, the display will light up as
follows.
4. Press the > button and confirm the display.
5. Press the > button, all segments are turned off.
6. Every pressing of the > button turns on each segments in
6. Every pressing of the > button turns on each segments in
the same order.
7. To exit from this mode, press the ?/1 button.
ALL1DISC S PGM
ALBM SHUF REP
ALBM SHUF REP
1
MP3 JPEG
SA - CD
SA - CD
MULTIPBC
DSGX
SB
DEC
kHz D
EX
DTS-ES NEO:6
ALBM
TITLE
TRK
CHAP
SLEEP
NTSC
TUNED
ST
MONO
NIGHT
a
MHz PL
II
a
ALL1DISC S PGM
ALBM SHUF REP
ALBM SHUF REP
1
MP3 JPEG
SA - CD
SA - CD
MULTIPBC
DSGX
SB
DEC
kHz D
EX
DTS-ES NEO:6
ALBM
TITLE
TRK
CHAP
SLEEP
NTSC
TUNED
ST
MONO
NIGHT
a
MHz PL
II
a
[Cold Reset]
*
The cold reset clears all data including preset data stored in
the RAM to initial conditions. Execute this mode when
returning the set to the customers.
the RAM to initial conditions. Execute this mode when
returning the set to the customers.
Procedure:
1. Press the ?/1 button to turn the power on.
2. Press three buttons of . , HX and A simultaneously.
3. When this button is operated, display as “COLD RESET” for
2. Press three buttons of . , HX and A simultaneously.
3. When this button is operated, display as “COLD RESET” for
a while and all of the settings are reset.
[Disc Slot Lock]
The disc slot lock function for the antitheft of an demonstration
disc in the store is equipped.
Setting Procedure:
disc in the store is equipped.
Setting Procedure:
1. Turn the set on.
2. Press two buttons of x and A simultaneously for five sec-
2. Press two buttons of x and A simultaneously for five sec-
onds.
3. The message “LOCKED” is displayed and the slot is locked.
Releasing Procedure:
1. Press two buttons of x and A simultaneously for five sec-
onds again.
2. The message “UNLOCKED” is displayed and the slot is
unlocked.
Note:
When “LOCKED” is displayed, the slot lock is not released by
turning power on/off with the ?/1 button.
turning power on/off with the ?/1 button.
[Repeat Limit Release Mode]
Procedure:
1. Press three buttons of A , > and [VOLUME+] simulta-
neously.
2. Repeat limit is released.
[CDM Ship Mode]
*
This mode moves the optical pick-up to the position durable
to vibration. Use this mode when returning the set to the
customer after repair.
to vibration. Use this mode when returning the set to the
customer after repair.
Procedure:
1. Turn the set on.
2. Set the function to DVD.
3. Press three buttons of > , . and A simultaneously.
4. The message “MECHA LOCK” is displayed.
5. The CDM ship mode is set.
2. Set the function to DVD.
3. Press three buttons of > , . and A simultaneously.
4. The message “MECHA LOCK” is displayed.
5. The CDM ship mode is set.
24
HCD-FR10W
[GENERAL DESCRIPTION]
The Test Mode allows you to make diagnosis and adjustment easily
using the remote commander and monitor TV. The instructions,
diagnostic results, etc. are given on the on-screen display (OSD).
using the remote commander and monitor TV. The instructions,
diagnostic results, etc. are given on the on-screen display (OSD).
[TEST DISC LIST]
Use the following test disc on test mode.
TDV-520CSO (DVD-SL)
TDV-520CSO (DVD-SL)
: PART No. J-2501-236-A
LUV-P01 (CD)
: PART No. 4-999-032-01
TDV-540C (DVD-DL)
: PART No. J-2501-235-A
Note:
Do not use exiting test disc for DVD.
[STARTING TEST MODE]
1. Press the @/1 button to turn the power on, and set the function
to DVD.
2. Press three buttons of A , x and [VOLUME+] simultaneously
to enter the test mode.
3. It displays “SERVICE IN” on the fluorescent indicator tube,
and displays the Test Mode Menu on the monitor screen as
follows. (At the bottom of the menu screen, the model name
and revision number are displayed)
follows. (At the bottom of the menu screen, the model name
and revision number are displayed)
4. To execute each function, select the desired menu and press
its number on the remote commander (RM-SP350).
5. To release from test mode, press the @/1 button and turn the
power off.
[OPERATING TEST MODE]
0. SYSCON DIAGNOSIS
The same contents as board detail check by serial interface can be
checked from the remote commander operation.
On the Test Mode Menu screen, press [0] key on the remote
commander, and the following Check Menu will be displayed.
checked from the remote commander operation.
On the Test Mode Menu screen, press [0] key on the remote
commander, and the following Check Menu will be displayed.
0-0. Quit
Quit the Syscon Diagnosis and return to the Test Mode Menu.
Test Mode Menu
0. Syscon Diagnosis
1. Drive Auto Adjustment
2. Drive Manual Operation
3. Mecha Aging
4. Emergency History
5. Mecha Error History
6. Version Information
7. Video Level Adjustment
Exit: POWER Key
Model :DAV-xxx xx
Revision :x.xx
### Syscon Diagnosis ###
Check Menu
0. Quit
1. All
2. Version
3. EEPROM
4. GPIO
5. SD Bus
6. Video
0-1. All (All items continuous check)
This menu checks all diagnostic items continuously. Normally, all
items are checked successively one after another automatically
unless an error is found, but at a certain item that requires judgment
through a visual check to the result, the following screen is displayed
for the key entry.
items are checked successively one after another automatically
unless an error is found, but at a certain item that requires judgment
through a visual check to the result, the following screen is displayed
for the key entry.
• Example display
For the ROM Check, the check sum calculated by the Syscon is
output, and therefore you must compare it with the specified value
for confirmation.
Following the message, press the > button to go to the next
item, or press the . button to repeat the same operation again.
To quit the diagnosis and return to Check Menu screen, press the
[RETURN] key on the remote commander to display Check Menu.
output, and therefore you must compare it with the specified value
for confirmation.
Following the message, press the > button to go to the next
item, or press the . button to repeat the same operation again.
To quit the diagnosis and return to Check Menu screen, press the
[RETURN] key on the remote commander to display Check Menu.
• Error occurred
If an error occurred, the diagnosis is suspended and error is displayed.
Press the [RETURN] key on the remote commander to quit the
diagnosis, or press the . button to repeat the same check where
an error occurred, or press the > button to continue the check
from the item next to faulty item.
If an error occurred, the diagnosis is suspended and error is displayed.
Press the [RETURN] key on the remote commander to quit the
diagnosis, or press the . button to repeat the same check where
an error occurred, or press the > button to continue the check
from the item next to faulty item.
General Description of Checking Method
Selecting 2 and subsequent items calls the submenu screen of each
item. And selecting 2 and subsequent items executes respective
menus and outputs the results.
For the contents of each submenu, see “Check Items List” as below.
item. And selecting 2 and subsequent items executes respective
menus and outputs the results.
For the contents of each submenu, see “Check Items List” as below.
Check Items List:
0-2. Version
0-2-1. All
0-2-2. Revision
0-2-3. ROM Check Sum
0-2-4. Model Type
0-2-5. Region
0-2-2. Revision
0-2-3. ROM Check Sum
0-2-4. Model Type
0-2-5. Region
0-3. EEPROM Check
0-3-1. Sampling Check
0-3-2. Detail Check
0-3-2. Detail Check
0-4. GP I/O Check
0-5. SD Bus Check
0-6. Video Check
0-5. SD Bus Check
0-6. Video Check
0-2. Version
0-2-2.
Revision
The revision number of ROM (IC205) that the program
for the DVD system processor (IC206) is stored.
The revision number of ROM (IC205) that the program
for the DVD system processor (IC206) is stored.
0-2-3.
ROM Check Sum
Check sum is calculated. (4 digits hexadecimal number)
Check sum is calculated. (4 digits hexadecimal number)
### Syscon Diagnosis ###
Diag All Check
No.2 Version
2-2. Version
ROM Revision = x.xx
Press NEXT Key to Continue
Press PREV Key to Repeat
Click on the first or last page to see other DAV-FR10W / HCD-FR10W service manuals if exist.