Sony CMT-V75BTIP Service Manual ▷ View online
CMT-V75BTiP
17
2-17. LOUDSPEAKER (67 × 108 mm) (L/R-CH) (SP3, SP4)
2-16. RMC BOARD
3
Remove the RMC board
in the direction of an arrow.
5
RMC board
4
connector
(CN1151)
1
cushion
(C)
cushion (C)
(Wire fixed.)
(Wire fixed.)
cushion (C)
(Wire fixed.)
(Wire fixed.)
cushion (K)
(Twist around
a wire.)
(Twist around
a wire.)
1
two cushions (C)
2
screw (BTTP M2.6)
:LUHVHWWLQJ
–)URQWERWWRPVLGHYLHZ–
Insert is shallow
Insert is straight
to the interior.
to the interior.
connector
Insert is incline
connector
connector
connector
connector
connector
NG
OK
NG
Note: When you install the connector, please install them correctly.
There is a possibility that this machine damages when not
correctly installing it.
1
two cushions (C)
1
two cushions (C)
2
screw
(BVTP3
u 8)
2
screw
(BVTP3
u 8)
2
screw
(BVTP3
u 8)
3
loudspeaker (67
u 108 mm)
(L-CH)
(SP3)
3
loudspeaker (67
u 108 mm)
(R-CH)
(SP4)
2
screw
(BVTP3
u 8)
2
two screws
(BVTP3
u 8)
2
two screws
(BVTP3
u 8)
Note: When installing loudspeaker (67 × 108 mm) (R-CH) (SP4),
check that the speaker wire has got into a ditch of box (SS R).
speaker wire
box (SS R)
Note: When installing loudspeaker (67 × 108 mm) (L-CH) (SP3),
check that the speaker wire has got into a ditch of box (SS L).
speaker wire
box (SS L)
CMT-V75BTiP
18
2-18. LOUDSPEAKER (6.5 cm) (L/R-CH) (SP1, SP2)
1
cushion
(S)
3
cushion (SPK wire)
2
ferrite core
(FC1)
5
cushion
(K)
5
cushion (K)
cushion (K)
cushion (K)
cushion (K)
cushion (LCD)
cushion (K)
4
cushion (LCD)
5
two cushions
(K)
5
two cushions (K)
5
two cushions (K)
6
four screws
(BVTP3
u 8)
6
four screws
(BVTP3
u 8)
7
Remove the loudspeaker (6.5 cm) (L-CH)
(SP1) in the direction of an arrow.
7
Remove the loudspeaker (6.5 cm)
(R-CH) (SP2) in the direction of an
arrow.
9
loudspeaker (6.5 cm) (L-CH) (SP1)
9
loudspeaker (6.5 cm)
(R-CH)
(SP2)
red (
+)
8
Remove solder
from
the
“
+” terminal.
black (
−)
8
Remove solder
from
the
“
−” terminal.
black (
−)
8
Remove solder
from
the
“
−” terminal.
red (
+)
red terminal
red terminal
silver terminal
8
Remove solder
from
the
“
+” terminal.
)HUULWHFRUH)&VHWWLQJ
Roll the wire once.
ferrite core (FC1)
Be based on
a marking line.
a marking line.
WireVHWWLQJ
silver terminal
WireVHWWLQJ
cushion (K)
WireVHWWLQJ
CMT-V75BTiP
19
2-20. SOLDERING OF SHORT-LAND
Note 1: Be sure to solder the short-land of SHORTLAND board before removing a wire.
Note 2: When assembling, be sure to remove solder, after checking that all the wires are connected.
Note 2: When assembling, be sure to remove solder, after checking that all the wires are connected.
2-19. TOP BLOCK
2
claw
3
Remove the top block in
the direction of an arrow.
4
top block
1
six screws
(P2
u 5)
– Panel (back) block front bottom side view –
1
Solder the short-land on the SHORTLAND board.
SHORTLAND board
– Chassis (main) block –
rear side view
CMT-V75BTiP
20
2-22. LCD BOARD
2-21. DAB BOARD, MODULE (DAB TUNER) (DAB1)
3
screw
(BVTT3
u 6)
5
cushion (U)
6
cushion (Y)
7
cushion (LED PC board)
3
screw
(BVTT3
u 6)
1
flexible flat cable (15 core)
(CN1352)
4
Remove the LCD board
in the direction of an arrow.
8
LCD board
5
cushion (U)
2
cushion (M)
colored line
colored line
Insert is straight to the interior.
Insert is incline
flexible flat
cable
cable
flexible flat
cable
cable
connector
connector
OK
NG
Note: When installing the flexible flat
cable, ensure the colored line.
No slanting after insertion.
– Chassis (main) block rear side view –
3
three screws
(BVTT3
u 6)
5
connector
(CN1601)
6
connector
(CN1604)
9
pin header 2P (CN1)
0
module (DAB tuner) (DAB1)
7
DAB board
4
Remove the DAB board block
in the direction of an arrow.
8
Remove two solders.
1
cushion (touch)
2
wire (flat type) (9 core)
(CN1602)
colored line
colored line
Insert is straight to the interior.
Insert is incline
flexible flat
cable
cable
flexible flat
cable
cable
connector
connector
OK
NG
Note: When installing the flexible flat
cable, ensure the colored line.
No slanting after insertion.
– Chassis (main) block –
rear side view
Click on the first or last page to see other CMT-V75BTIP service manuals if exist.