Panasonic KX-NT136RU Service Manual ▷ View online
KX-NT136RU
(for Russia)
IP Proprietary Telephone
IMPORTANT INFORMATION ABOUT LEAD FREE, (PbF), SOLDERING
If lead free solder was used in the manufacture of this product the printed circuit boards will be marked PbF.
Standard leaded, (Pb), solder can be used as usual on boards without the PbF mark.
Standard leaded, (Pb), solder can be used as usual on boards without the PbF mark.
When this mark does appear, please read and follow the special instructions described in this manual on the use of PbF and how
it might be permissible to use Pb solder during service and repair work.
it might be permissible to use Pb solder during service and repair work.
ORDER NO. KMS0511164CE
1 ABOUT LEAD FREE SOLDER (PbF: Pb free)
3
1.1.
SUGGESTED PbF SOLDER
3
1.2.
HOW TO RECOGNIZE THAT Pb FREE SOLDER IS
USED
4
2 FOR SERVICE TECHNICIANS
5
3 SPECIFICATIONS
6
4 LOCATION OF CONTROLS
7
5 CONNECTION
8
5.1.
OPTIONAL ACCESORY
8
6 DISASSEMBLY INSTRUCTIONS
9
7 BLOCK DIAGRAM
11
8 CIRCUIT OPERATIONS
12
8.1.
MAIN-CPU (IC1)
12
8.2.
LCD CIRCUIT
12
8.3.
RESET CIRCUIT
13
8.4.
Ethernet CIRCUIT
13
8.5.
CODEC(IC7) [ANALOG] CIRCUIT
14
8.6.
SUB-CPU (IC13)
15
8.7.
KEY INPUT CONTROL CIRCUIT
16
8.8.
LED CIRCUIT
17
8.9.
POWER SUPPLY CIRCUIT
18
9 TROUBLESHOOTING GUIDE
19
9.1.
NO OPERATION
19
9.2.
LCD DOES NOT OPERATE
21
9.3.
HANDSET DOES NOT WORK
22
9.4.
HEADSET DOES NOT WORK
23
9.5.
SPEAKER-PHONE DOES NOT WORK
24
9.6.
Ethernet DOES NOT WORK (LAN PORT)
25
9.7.
Ethernet DOES NOT WORK (PC PORT)
26
10 IC DATA
27
10.1. IC1 (MAIN-CPU)
27
10.2. IC7 (CODEC)
32
10.3. IC12
34
10.4. IC13 (SUB-CPU)
37
10.5. IC301 (DC-CON)
39
10.6. IC302 (PoE 802.3af)
40
11 TERMINAL GUIDE OF ICs, TRANSISTORS AND DIODES
41
12 HOW TO REPLACE A FLAT PACKAGE IC
42
12.1. PREPARATION
42
12.2. PROCEDURE
42
12.3. REMOVING SOLDER FROM BETWEEN PINS
42
13 CABINET AND ELECTRICAL PARTS LOCATION
43
14 ACCESSORIES AND PACKING MATERIALS
44
15 REPLACEMENT PARTS LIST
45
15.1. CABINET AND ELECTRICAL PARTS
45
15.2. ACCESSORIES AND PACKING MATERIALS
45
15.3. MAIN BOARD PARTS
45
15.4. SUB BOARD PARTS
49
15.5. POWER BOARD PARTS
49
16 FOR THE SCHEMATIC DIAGRAM
50
17 SCHEMATIC DIAGRAM
51
17.1. SUB (KEY/HEADSET/LED block)
51
17.2. MAIN No1. (MAIN CPU block)
52
17.3. MAIN No2. (CODEC block)
56
17.4. MAIN No3. (XPHY block)
58
17.5. MAIN No4. (SUB CPU block)
60
17.6. POWER SUPPLY
62
17.7. WAVEFORM
63
18 PRINTED CIRCUIT BOARD
66
18.1. MAIN BOARD
66
18.2. SUB BOARD
68
18.3. POWER BOARD
68
CONTENTS
Page
Page
2
KX-NT136RU
1 ABOUT LEAD FREE SOLDER (PbF: Pb free)
Note:
In the information below, Pb, the symbol for lead in the periodic table of elements, will refer to standard solder or solder that
contains lead.
contains lead.
We will use PbF solder when discussing the lead free solder used in our manufacturing process which is made from Tin, (Sn),
Silver, (Ag), and Copper, (Cu).
Silver, (Ag), and Copper, (Cu).
This model, and others like it, manufactured using lead free solder will have PbF stamped on the PCB. For service and repair
work we suggest using the same type of solder although, with some precautions, standard Pb solder can also be used.
work we suggest using the same type of solder although, with some precautions, standard Pb solder can also be used.
Caution
•
•
•
• PbF solder has a melting point that is 50° ~ 70° F, (30° ~ 40°C) higher than Pb solder. Please use a soldering iron with
temperature control and adjust it to 700° ± 20° F, (370° ± 10°C). In case of using high temperature soldering iron, please
be careful not to heat too long.
be careful not to heat too long.
•
•
•
• PbF solder will tend to splash if it is heated much higher than its melting point, approximately 1100°F, (600°C).
•
•
•
• If you must use Pb solder on a PCB manufactured using PbF solder, remove as much of the original PbF solder as possible
and be sure that any remaining is melted prior to applying the Pb solder.
•
•
•
• When applying PbF solder to double layered boards, please check the component side for excess which may flow onto the
opposite side (See figure, below).
1.1. SUGGESTED PbF SOLDER
There are several types of PbF solder available commercially. While this product is manufactured using Tin, Silver, and Copper,
(Sn+Ag+Cu), you can also use Tin and Copper, (Sn+Cu), or Tin, Zinc, and Bismuth, (Sn+Zn+Bi).
Please check the manufacturer’s specific instructions for the melting points of their products and any precautions for using their
product with other materials.
The following lead free (PbF) solder wire gauges are recommended for service of this product: 0.3mm, 0.6mm and 1.0mm.
(Sn+Ag+Cu), you can also use Tin and Copper, (Sn+Cu), or Tin, Zinc, and Bismuth, (Sn+Zn+Bi).
Please check the manufacturer’s specific instructions for the melting points of their products and any precautions for using their
product with other materials.
The following lead free (PbF) solder wire gauges are recommended for service of this product: 0.3mm, 0.6mm and 1.0mm.
3
KX-NT136RU
1.2. HOW TO RECOGNIZE THAT Pb FREE SOLDER IS USED
“PbF” is marked to show that Pb free solder is used. (See the figure below.)
4
KX-NT136RU