Sony CMT-V75BTIP Service Manual ▷ View online
CMT-V75BTiP
13
2-11. D LED R BOARD, D LED L BOARD, IP JUNC BOARD
:LUHVHWWLQJ
1
two claws
5
three claws
3
two claws
2
Remove the D LED R board
in the direction of an arrow.
9
D LED R board
qa
D LED L board
4
Remove the D LED L board
in the direction of an arrow.
6
Remove the IP JUNC board
in the direction of an arrow.
qf
IP JUNC board
8
connector
(CN1521)
qs
connector (CN1534)
qd
connector (CN1536)
q;
connector
(CN1511)
7
flexible flat cable
(16 core) (CN1533)
Insert is shallow
Insert is straight
to the interior.
to the interior.
connector
Insert is incline
connector
connector
connector
connector
connector
NG
OK
NG
D LED R board
D LED L board
IP JUNC board
Note 2: When installing the flexible
flat cable, ensure the colored
line.
No slanting after insertion.
Note 1: When you install the connector, please
install them correctly.
There is a possibility that this machine
damages when not correctly installing it.
colored line
colored line
Insert is straight to the interior.
Insert is incline
flexible flat
cable
cable
flexible flat
cable
cable
connector
connector
OK
NG
IP JUNC board
claw
claw
claw
D LED L board
claw
claw
D LED R board
ditch
ditch
claw
claw
–3DQHOGRFNERWWRP–
EORFNUHDUVLGHYLHZ
CMT-V75BTiP
14
2-13. IP DOCK BOARD
2-12. SPRING (LOCK)
1
claw
1
claw
2
lever (dock lock IP)
3
spring (lock)
– Panel (dock bottom) block rear side view –
1
two claws
7
two claws
holder (IP)
4
claw
4
claw
2
two shafts
3
spring (holder)
spring (holder)
5
Remove the IP DOCK board block
in the direction of an arrow.
9
IP DOCK board
6
flexible flat cable (16 core)
(CN1502)
IP JUNC board
6SULQJKROGHUVHWWLQJ
colored line
colored line
Insert is straight to the interior.
Insert is incline
flexible flat
cable
cable
flexible flat
cable
cable
connector
connector
OK
NG
Note: When installing the flexible flat
cable, ensure the colored line.
No slanting after insertion.
8
holder (IP) block
–3DQHOGRFNERWWRPEORFNUHDUVLGHYLHZ–
CMT-V75BTiP
15
2-14. FRONT BLOCK
– Rear side view –
4
screw
(BVTP3
u 10)
1
Insert a thin pin etc. below the
cap (rear) and remove to pull
and raise the cap (rear).
cap (rear)
8
screw
(BVTP3
u 8)
9
lug wire
0
front block
5
two claws
5
two claws
4
screw
(BVTP3
u 10)
2
cap (rear L)
block
3
cap (rear R)
block
6
Rotate a front block from one side,
remove one claw at a time.
lug wire
box (SS L)
mechanism deck
(BSXD1-DVBU201)
(BSXD1-DVBU201)
:ire seWWiQJ
box (SS L)
POWER KEY board
7
cushion (SUP)
cushion (SUP)
CMT-V75BTiP
16
2-15. CHASSIS (MAIN) BLOCK
7
connector
(CN107)
0
connector
(CN1001)
qa
connector
(CN1003)
4
connector
(CN1251)
3
connector
(CN1451)
box (SS R)
:LUHVHWWLQJ
KEY board
mechanism deck
(BSXD1-DVBU201)
(BSXD1-DVBU201)
Insert is shallow
Insert is straight
to the interior.
to the interior.
connector
Insert is incline
connector
connector
connector
connector
connector
NG
OK
NG
Note 3: When installing the flexible
flat cable, ensure the colored
line.
No slanting after insertion.
Note 2: When you install the connector, please
install them correctly.
There is a possibility that this machine
damages when not correctly installing it.
Note 1: The wire must not touch the mechanism
deck
deck
(BSXD1-DVBU201).
colored line
colored line
Insert is straight to the interior.
Insert is incline
flexible flat
cable
cable
flexible flat
cable
cable
connector
connector
OK
NG
5
screw
(BVTP3
u 8)
5
two screws
(BVTP3
u 8)
6
Remove the chassis (main)
block in the direction of an
arrow.
qs
chassis (main) block
9
Remove the ferrite core from the coating clip.
8
flexible flat cable
(7
core)
–)URQWWRSVLGHYLHZ–
MAIN board
JACK board
:LUHVHWWLQJ
ferrite core
coating clip
1
cushion
(SUP)
2
connector
(CN1202)
cushion (SUP)
Click on the first or last page to see other CMT-V75BTIP service manuals if exist.