Sony CMT-V50IP Service Manual ▷ View online
CMT-V50iP
13
2-11. D LED R BOARD, D LED L BOARD, IP JUNC BOARD
:LUHVHWWLQJ
6KHHWSDQHOERWWRP:0$VHWWLQJ
/,*+76,/9(5
3,1.
3,1.
1
two sheets
(panel
bottom
WM
A)
sheet (panel bottom WM A)
rib
rib
sheet (panel bottom WM A)
2
two claws
6
three claws
4
two claws
3
Remove the D LED R board
in the direction of an arrow.
0
D LED R board
qs
D LED L board
5
Remove the D LED L board
in the direction of an arrow.
7
Remove the IP JUNC board
in the direction of an arrow.
qg
IP JUNC board
9
connector
(CN1521)
qd
connector (CN1534)
qf
connector (CN1536)
qa
connector
(CN1511)
8
flexible flat cable
(16 core) (CN1533)
Insert is shallow
Insert is straight
to the interior.
to the interior.
connector
Insert is incline
connector
connector
connector
connector
connector
1*
2.
1*
D LED R board
D LED L board
IP JUNC board
Note 2: When installing the flexible
flat cable, ensure the colored
line.
No slanting after insertion.
Note 1: When you install the connector, please
install them correctly.
There is a possibility that this machine
damages when not correctly installing it.
colored line
colored line
Insert is straight to the interior.
Insert is incline
flexible flat
cable
cable
flexible flat
cable
cable
connector
connector
2.
1*
–3DQHOGRFNERWWRP–
EORFNUHDUVLGHYLHZ
IP JUNC board
claw
claw
claw
D LED L board
D LED L board
claw
claw
D LED R board
ditch
ditch
D LED R board
claw
claw
CMT-V50iP
14
2-13. IP DOCK BOARD
2-12. SPRING (LOCK)
– Panel (dock bottom) block rear side view –
1
claw
1
claw
2
lever (dock lock IP)
3
spring (lock)
1
two claws
7
two claws
8
holder (IP) block
holder (IP)
4
claw
4
claw
2
two shafts
3
spring (holder)
spring (holder)
5
Remove the IP DOCK board block
in the direction of an arrow.
9
IP DOCK board
6
flexible flat cable (16 core)
(CN1502)
IP JUNC board
6SULQJKROGHUVHWWLQJ
colored line
colored line
Insert is straight to the interior.
Insert is incline
flexible flat
cable
cable
flexible flat
cable
cable
connector
connector
OK
NG
Note: When installing the flexible flat
cable, ensure the colored line.
No slanting after insertion.
–3DQHOGRFNERWWRPEORFNUHDUVLGHYLHZ–
CMT-V50iP
15
2-14. FRONT BLOCK
– Rear side view –
8
screw
(BVTP3
u 8)
9
lug wire
7
cushion (SUP)
0
front block
5
two claws
5
two claws
6
Rotate a front from block one side,
remove one claw at a time.
lug wire
box (SS L)
mechanism deck
(BSXD1-DVBU201)
(BSXD1-DVBU201)
:LUHVHWWLQJ
cushion (SUP) box (SS L)
POWER KEY board
4
screw
(BVTP3
u 10)
1
Insert a thin pin etc. below the
cap (rear) and remove to pull
and raise the cap (rear).
cap (rear)
4
screw
(BVTP3
u 10)
2
cap (rear L)
block
3
cap (rear R)
block
CMT-V50iP
16
2-15. CHASSIS (MAIN) BLOCK
1
cushion
(SUP)
2
connector
(CN1202)
7
connector
(CN107)
0
connector
(CN1001)
qa
connector
(CN1003)
4
connector
(CN1251)
3
connector
(CN1451)
cushion (SUP)
box (SS R)
:LUHVHWWLQJ
KEY board
mechanism deck
(BSXD1-DVBU201)
(BSXD1-DVBU201)
Insert is shallow
Insert is straight
to the interior.
to the interior.
connector
Insert is incline
connector
connector
connector
connector
connector
NG
OK
NG
Note 3: When installing the flexible
flat cable, ensure the colored
line.
No slanting after insertion.
Note 2: When you install the connector, please
install them correctly.
There is a possibility that this machine
damages when not correctly installing it.
Note 1: The wire must not touch the mechanism
deck
deck
(BSXD1-DVBU201).
colored line
colored line
Insert is straight to the interior.
Insert is incline
flexible flat
cable
cable
flexible flat
cable
cable
connector
connector
OK
NG
5
screw
(BVTP3
u 8)
5
two screws
(BVTP3
u 8)
6
Remove the chassis (main)
block in the direction of an
arrow.
qs
chassis (main) block
9
Remove the ferrite core from the coating clip.
8
flexible flat cable
(7
core)
–)URQWWRSVLGHYLHZ–
MAIN board
JACK board
:LUHVHWWLQJ
ferrite core
coating clip
Click on the first or last page to see other CMT-V50IP service manuals if exist.