Sony CMT-F3MD / HCD-F3MD Service Manual ▷ View online
77
Pin No.
Pin Name
I/O
Description
1
STKPOWER
O
Power amplifier (IC801) on/off selection signal output terminal “H”: power amplifier on
2
P
O
Power on/off control signal output terminal Not used (open)
3
F-RY
O
Speakers on/off relay (RY881) drive signal output terminal “H”: speakers on
4
R-RY
O
Rear speakers on/off relay drive signal output terminal “H”: speakers on Not used (open)
5
CD-POWER
O
Power on/off control signal output for the CD servo section “L”: standby, “H”: power on
6
TA-MUTE
O
Line muting on/off signal output terminal “L”: muting on
7
DBFB-H
O
H/L selection signal output terminal for DBFB Not used (open)
8
BYTE
I
External data bus line byte selection signal input “L”: 16 bits, “H”: 8 bits
Not used (fixed at “L”)
Not used (fixed at “L”)
9
CNVSS
—
Ground terminal
10
SUBXIN
I
Sub system clock input terminal (32.768 kHz)
11
SUBXOUT
O
Sub system clock output terminal (32.768 kHz)
12
RESET
I
System reset signal input from the reset signal generator (IC941) “L”: reset
For several hundreds msec. after the power supply rises, “L” is input, then it changes to “H”
For several hundreds msec. after the power supply rises, “L” is input, then it changes to “H”
13
XOUT
O
Main system clock output terminal (16 MHz)
14
VSS
—
Ground terminal
15
XIN
I
Main system clock input terminal (16 MHz)
16
VCC
—
Power supply terminal (+5V)
17
NMI
I
Non-maskable interrupt input terminal Fixed at “H” in this set
18
WAKE-UP
I
System wake up signal input terminal Not used (fixed at “L”)
19
SCOR
I
Subcode sync (S0+S1) detection signal input from the CXD2587Q (IC101)
20
RDS-INT
I
Interrupt status input from the tuner pack Not used (open)
21
RDS-DATA
I
Serial data input from the tuner pack Not used (open)
22
AC-CUT
I
AC off detection signal input from the voltage detector (IC941) “L”: AC off
23
PL-CLK
O
Serial data transfer clock signal output to pro-logic circuit Not used (open)
24
PL-DATA
O
Serial data output to pro-logic circuit Not used (open)
25
PL-LAT
O
Serial data latch pulse output to pro-logic circuit Not used (open)
26
TIMER-LED
O
LED drive signal output of the timer indicator Not used (open)
27
PROTECT-IN
I
Over load detection signal input for speaker output “L”: over load
28
MD-RESET
O
MD reset signal output terminal Not used (open)
29
IIC-SCL
I/O
Shift clock signal input/output terminal for the IIC bus
30
IIC-DAT
I/O
Data input/output terminal for the IIC bus
31
TXD
—
Not used (fixed at “L”)
32
SQ-DATA-IN
I
Subcode Q data input from the CXD2587Q (IC101)
33
SQ-CLK
O
Subcode Q data reading clock signal output to the CXD2587Q (IC101)
34
FL-RESET
O
Reset signal output to the FL driver (IC601) “L”: reset
35
FL-DATA
O
Serial data output to the FL driver (IC601)
36
FL-CHIP SELECT
O
Chip select signal output to the FL driver (IC601) “L”: active
37
FL-CLK
O
Serial data transfer clock signal output to the FL driver (IC601)
38
62LAT
O
Serial data latch pulse signal output to the M62428AFP (IC301)
39
STBY-LED
O
LED drive signal output of the standby indicator Not used (open)
40, 41
V-CINE
O
Not used (open)
42
FL-ON
O
FL power on/off control signal output terminal Not used (open)
43
POWER-ON
O
Standby relay drive signal output terminal “L”: standby, “H”: power on
44
B-FREQ
O
Not used (open)
45
FUNC-SEL1
O
Function selection signal output terminal Not used (open)
• MAIN BOARD IC501 M30620MCA-A51FP (MASTER CONTROLLER)
78
Pin No.
Pin Name
I/O
Description
46
OPT-SEL
O
Optical signal selection signal output terminal Not used (open)
47
62DATA
O
Serial data output to the M62428AFP (IC301)
48
62CLK
O
Serial data transfer clock signal output to the M62428AFP (IC301)
49
ST-MUTE
O
Tuner muting control signal output to the tuner pack “L”: muting on
50
STEREO
I
FM stereo detection signal input from the tuner pack
51
TUNED
I
Tuning detection signal input from the tuner pack
52
ST-CE
O
PLL chip enable signal output to the tuner pack
53
ST-DOUT
O
PLL serial data output to the tuner pack
54
ST-DIN
I
PLL serial data input from the tuner pack
55
ST-CLK
O
PLL serial data transfer clock signal output to the tuner pack
56
SENSE
I
Internal status detection monitor input from the CXD2587Q (IC101)
57
HOLD
O
Automatic power control hold signal output to the CXA2568M (IC103)
58
CD-LAT
O
Serial data latch pulse output to the CXD2587Q (IC101)
59
CD-RESET
O
Reset signal output to the CXD2587Q (IC101) and BA5974FP (IC102)
60
DISC-SENS
I
Detection input from the disc in detect switch Not used (fixed at “H”)
61
TABLE-SENS
I
Detection input from the disc tray detect switch Not used (fixed at “H”)
62
VCC
—
Power supply terminal (+5V)
63
TABLE-L
O
Disc tray open/close motor drive signal output terminal Not used (open)
64
VSS
—
Ground terminal
65
TABLE-R
O
Disc tray open/close motor drive signal output terminal Not used (open)
66
LOAD-OUT
O
CD loading motor control signal output to the motor driver (IC171)
67
LOAD-IN
O
CD loading motor control signal output to the motor driver (IC171)
68
UP-SW
I
Not used (fixed at “L”)
69
DISC-LED
I
Not used (fixed at “L”)
70
IN-SW
I
Detection input from the CD disc tray open/close detect switch (S1)
“L”: CD disc tray close
“L”: CD disc tray close
71
OUT-SW
I
Detection input from the CD disc tray open/close detect switch (S1)
“L”: CD disc tray open
“L”: CD disc tray open
72
LED
O
LED drive signal output of the CD playback indicator (D665 (green)) “L”: LED on
73
LED
O
LED drive signal output of the MD disc in indicator (D664) “H”: LED on
74
LED
O
LED drive signal output of the MD playback indicator (D661 (green)) “L”: LED on
75
LED
O
LED drive signal output of the MD pause indicator (D661 (amber)) “L”: LED on
76
LED
O
LED drive signal output of the CD playback indicator (D665 (amber)) “L”: LED on
77
LED
O
LED drive signal output of the CD disc in indicator (D667) “H”: LED on
78
LED
O
LED drive signal output of the MD recording indicator (D663) “H”: LED on
79
STANDBY
O
LED drive signal output of the standby indicator (D668) “H”: LED on
80
LED
O
LED drive signal output terminal Not used (open)
81
CD-DATA
O
Serial data output to the CXD2587Q (IC101)
82
CD-CLK
O
Serial data transfer clock signal output to the CXD2587Q (IC101)
83
REC OUT CONT
O
Muting on/off control signal output of tape output signal “L”: muting on
84
JOGA
I
Jog dial pulse input from the rotary encoder A phase input Not used (open)
85
JOGB
I
Jog dial pulse input from the rotary encoder B phase input Not used (open)
86
VOL A
I
Jog dial pulse input from the rotary encoder (S601 VOLUME) A phase input
87
VOL B
I
Jog dial pulse input from the rotary encoder (S601 VOLUME) B phase input
88
SIRCS
I
Remote control signal input from the remote control receiver (IC602)
89
KEY0
I
Key input terminal (A/D input) S602 (I/1 key input)
79
Pin No.
Pin Name
I/O
Description
90
KEY1
I
Key input terminal (A/D input) S603 to 608 (CDs, CDHS, CDA, MDs, MDHS, MDA,
keys input)
keys input)
91
KEY2
I
Key input terminal (A/D input) S609 to 616 (FUNCTION, +M L, TUNER/BAND, –l
m, z REC, CD-MD SYNC, STEREO/MONO REPEAT, TUNING MODE/PLAY MODE keys
input)
m, z REC, CD-MD SYNC, STEREO/MONO REPEAT, TUNING MODE/PLAY MODE keys
input)
92
MD-REC-R
I
R-ch level input from the MD mechanism controller (IC316)
93
HEADPHONE
I
Headphone detection signal input terminal “H”: headphone in
94
MD-REC-L
I
L-ch level input from the MD mechanism controller (IC316)
95
MODEL-IN
I
Model destination setting terminal
96
AG
—
Ground terminal
97
SPEC-IN
I
Model specification setting terminal
98
VREF
I
Reference voltage (+5V) input terminal
99
AVCC
—
Power supply terminal (+5V)
100
TEST
—
Test setting terminal (fixed at “L”)
80
supplied with S601
not supplied
#1
#1
#2
FL601
MDM-5GA
1
2
5
4
3
10
15
16
14
13
17
18
19
12
19
19
11
9
11
21
21
20
20
8
7
10
not supplied
(1)
CASE, FRONT PANEL SECTION
SECTION 7
EXPLODED VIEWS
The components identified by
mark 0 or dotted line with mark
mark 0 or dotted line with mark
0 are critical for safety.
Replace only with part number
specified.
Replace only with part number
specified.
• Items marked “*” are not stocked since they
are seldom required for routine service. Some
delay should be anticipated when ordering
these items.
delay should be anticipated when ordering
these items.
• The mechanical parts with no reference num-
ber in the exploded views are not supplied.
• Hardware (# mark) list and accessories and
packing materials are given in the last of the
electrical parts list.
electrical parts list.
NOTE:
• -XX and -X mean standardized parts, so they
may have some difference from the original
one.
one.
• Color Indication of Appearance Parts
Example:
KNOB, BALANCE (WHITE) . . . (RED)
KNOB, BALANCE (WHITE) . . . (RED)
↑
↑
Parts Color Cabinet's Color
Ref. No.
Part No.
Description
Remark
Ref. No.
Part No.
Description
Remark
1
4-228-468-01 KNOB (VOL)
2
4-228-471-01 PLATE (FL), INDICATION (SILVER)
2
4-228-471-11 PLATE (FL), INDICATION (WHITE)
3
X-4952-957-4 PANEL ASSY, FRONT (S) (SILVER)
3
X-4952-996-4 PANEL ASSY (W), FRONT (WHITE)
4
4-216-729-71 LID (CARTRIDGE)
5
4-223-771-21 SPRING (LID)
7
A-4475-916-A PANEL BOARD, COMPLETE
8
4-212-590-22 HOLDER (FL)
* 9
4-228-798-41 CASE (SILVER)
* 9
4-228-798-51 CASE (WHITE)
10
3-363-099-11 SCREW (CASE 3 TP2)
11
4-212-589-01 SCREW (+BVTPWH M3), STEP
12
4-221-097-02 BRACKET (MDM)
13
1-777-240-11 WIRE (FLAT TYPE) (21 CORE)
14
1-791-211-11 WIRE (FLAT TYPE) (23 CORE)
15
A-4475-917-A MD DIGITAL BOARD, COMPLETE
16
1-773-212-11 WIRE (FLAT TYPE) (25 CORE)
17
1-792-756-11 WIRE (FLAT TYPE) (29 CORE)
18
4-228-469-01 PANEL, LOADING (SILVER)
18
4-228-469-11 PANEL, LOADING (WHITE)
19
4-951-620-01 SCREW (2.6X8), +BVTP
20
4-996-223-01 INSULATOR (F) (BLACK)
21
4-999-347-01 INSULATOR (R) (GREEN)
FL601
1-517-985-11 INDICATOR TUBE, FLUORESCENT
• Abbreviation
HK : Hong Kong model
KR
KR
: Korean model
TW : Taiwan model
Click on the first or last page to see other CMT-F3MD / HCD-F3MD service manuals if exist.