Sony CDP-CE575 Service Manual ▷ View online
33
CDP-CE575
Pin No.
Pin Name
I/O
Description
43
RFDC
I
RF signal input from the CXA2581N (IC131)
44
ADIO
O
Monitor output of the A/D converter input signal Not used (open)
45
AVSS0
—
Ground terminal (digital system)
46
IGEN
I
Stabilized current input for operational amplifiers
47
AVDD0
—
Power supply terminal (+5V) (digital system)
48
ASYO
O
Playback EFM full-swing output terminal
49
ASYI
I
Playback EFM asymmetry comparator voltage input terminal
50
BIAS
I
Playback EFM asymmetry circuit constant current input terminal
51
RFAC
I
EFM signal input from the CXA2581N (IC131)
52
AVSS3
—
Ground terminal (digital system)
53
CLTV
I
Internal VCO control voltage input of the playback master PLL
54
FILO
O
Filter output for master clock of the playback master PLL
55
FILI
I
Filter input for master clock of the playback master PLL
56
PCO
O
Phase comparison output for master clock of the playback EFM master PLL
57
AVDD3
—
Power supply terminal (+5V) (digital system)
58
VSS
—
Ground terminal (digital system)
59
VDD
—
Power supply terminal (+5V) (digital system)
60
DOUT
O
Digital audio signal output to the DIGITAL OUT OPTICAL (IC303)
61
LRCK
O
L/R sampling clock signal (44.1 kHz) output terminal Not used (open)
62
PCMD
O
D/A interface serial data output terminal Not used (open)
63
BCK
O
Bit clock signal (2.8224 MHz) output terminal Not used (open)
64
EMPH
O
De-emphasis control signal output terminal Not used (open)
65
XVDD
—
Power supply terminal (+5V) (crystal oscillator system)
66
XTAI
I
System clock input terminal (16.9344 MHz)
67
XTAO
O
System clock output terminal (16.9344 MHz)
68
XVSS
—
Ground terminal (crystal oscillator system)
69
AVDD1
—
Power supply terminal (+5V) (analog system)
70
AOUT1
O
L-ch analog audio signal output terminal
71
AIN1
I
L-ch operational amplifiers input terminal
72
LOUT1
O
L-ch line output terminal
73
AVSS1
—
Ground terminal (analog system)
74
AVSS2
—
Ground terminal (analog system)
75
LOUT2
O
R-ch line output terminal
76
AIN2
I
R-ch operational amplifiers input terminal
77
AOUT2
O
R-ch analog audio signal output terminal
78
AVDD2
—
Power supply terminal (+5V) (analog system)
79
RMUT
O
R-ch line muting on/off control signal output terminal
80
LMUT
O
L-ch line muting on/off control signal output terminal
34
CDP-CE575
•
MAIN BOARD IC301 CXP84648-085Q (SYSTEM CONTROLLER)
Pin No.
Pin Name
I/O
Description
1 to 4
A3 to A6
O
Address signal output to the static RAM (IC302)
5
GND
—
Ground terminal
6 to 13
D0 to D7
I/O
Two-way data bus with the static RAM (IC302)
14
CE
O
Chip select signal output to the static RAM (IC302)
15 to 18
NC
—
Not used (open)
19
WE
O
Write enable signal output to the static RAM (IC302)
20
LOAD OUT
O
Loading motor (M10) drive signal output to the BA6780 (IC11)
21
LOAD IN
O
Loading motor (M10) drive signal output to the BA6780 (IC11)
22
FL CLK
O
Serial data transfer clock signal output to the FL driver (IC801)
23
FL DATA
O
Serial data output to the FL driver (IC801)
24
FL RST
O
Reset signal output to the FL driver (IC801)
25 to 27
A13, A14, A7
O
Address signal output to the static RAM (IC302)
28
DSENS
I
Detect signal input from the disc sensor (D11)
29
NC
—
Not used (open)
30
RST
I
System reset signal input from the reset signal generator (IC603) “L”: reset
For several hundreds msec. after the power supply rises, “L” is input, then it changes to “H”
For several hundreds msec. after the power supply rises, “L” is input, then it changes to “H”
31
EXTAL
I
Main system clock input terminal (10 MHz)
32
XTAL
O
Main system clock output terminal (10 MHz)
33
VSS
—
Ground terminal
34
TX
O
Sub system clock output terminal Not used (open)
35
TEX
I
Sub system clock input terminal Not used (fixed at “L”)
36
AVSS
—
Ground terminal (for A/D converter)
37
AVREF
I
Reference voltage input terminal (+5V)
38
NC
—
Not used (open)
39
VERSION
I
Model Destination setting terminal
40
ADJ
I
Setting terminal for the test mode
41
KEY4
I
Key input terminal (A/D input) (S941 to S845) FADER, PEAK SEARCH, CLEAR, CHECK,
EDIT keys input
EDIT keys input
42
KEY3
I
Key input terminal (A/D input) (S831 to S838) DISC 5, DISC 4, DISC 3, DISC 2, DISC 1,
CONTINUE, SHUFFLE, PROGRAM keys input
CONTINUE, SHUFFLE, PROGRAM keys input
43
KEY2
I
Key input terminal (A/D input) (S821 to S827) MEGA CONTROL, X-FADER NO DELAY,
MENU, m (AMS–), M (AMS+), TIME/TEXT, REPEAT keys input
MENU, m (AMS–), M (AMS+), TIME/TEXT, REPEAT keys input
44
KEY1
I
Rotary encoder key input terminal (A/D input) (S801, S811 to S815) l AMS L (DISC)
PUSH ENTER, H, X, s, EX-CHANGE, DISC SKIP keys input
PUSH ENTER, H, X, s, EX-CHANGE, DISC SKIP keys input
45
NC
—
Not used (open)
46
TSENS
I
Detect signal input from the table sensor (D10)
47
FLT
O
Serial data latch pulse output to the FL driver (IC801)
48
CLK
O
Serial data transfer clock signal output to the CXD2587Q (IC101)
49
NC
O
Not used (open)
50
DATA
O
Serial data output to the CXD2587Q (IC101)
51
SQCK
O
Sub-code Q data reading clock signal output to the CXD2587Q (IC101)
52
SQSO
I
Sub-code Q data signal input from the CXD2587Q (IC101)
53
NC
—
Not used (open)
54
SENSE
I
Internal status (SENSE) signal input from the CXD2587Q (IC101)
55
NC
I
Not used (fixed at “H”)
56
RMIN
I
Remote control signal input from the remote control receiver (IC802)
35
CDP-CE575
Pin No.
Pin Name
I/O
Description
57
NC
I
Not used (fixed at “H”)
58
XLT
O
Serial data latch pulse signal output to the CXD2587Q (IC101)
59, 60
NC
—
Not used (open)
61
SCOR
I
Sub-code sync (S0+S1) detection signal input from the CXD2587Q (IC101)
62
BUSIN
I
Sircs remote control signal input from the CONTROL A1II
63
BUSOUT
O
Sircs remote control signal output to the CONTROL A1II
64
SMUTE
O
Muting on/off control signal output terminal “H” active
65
LDON/RW
O
Laser power control signal output to the CXA2581N (IC131) “H” active
66
TBLL
O
Table motor drive signal (counterclockwise) output to the BA6780 (IC11)
67
TBLR
O
Table motor drive signal (clockwise) output to the BA6780 (IC11)
68, 69
S2, S1
I
Detect signal input from the table address detect switch (S200)
70
OUT SW
I
Detect signal input from the open/close detect switch (S11)
71
A8
O
Address signal output to the static RAM (IC302)
72
VDD
—
Power supply terminal (+5V)
73
NC
—
Not used (fixed at “H”)
74 to 80
A9 to A12,
A0 to A2
O
Address signal output to the static RAM (IC302)
36
CDP-CE575
8-1. CASE SECTION
SECTION 8
EXPLODED VIEWS
• Items marked “*” are not stocked since they
are seldom required for routine service. Some
delay should be anticipated when ordering
these items.
delay should be anticipated when ordering
these items.
• The mechanical parts with no reference num-
ber in the exploded views are not supplied.
• Accessories and packing materials are given
in the last of the electrical parts list.
• Abbreviation
CND : Canadian model
NOTE:
• -XX and -X mean standardized parts, so they
may have some difference from the original
one.
one.
• Color Indication of Appearance Parts
Example:
KNOB, BALANCE (WHITE) . . . (RED)
KNOB, BALANCE (WHITE) . . . (RED)
↑
↑
Parts Color Cabinet's Color
Ref. No.
Part No.
Description
Remark
Ref. No.
Part No.
Description
Remark
Les composants identifiés par une
marque 0 sont critiquens pour la
sécurité.
Ne les remplacer que par une pièce
portant le numéro spécifié.
marque 0 sont critiquens pour la
sécurité.
Ne les remplacer que par une pièce
portant le numéro spécifié.
The components identified by mark
0 or dotted line with mark 0 are
critical for safety.
Replace only with part number
specified.
critical for safety.
Replace only with part number
specified.
2
3
2
1
Front panel section
#1
#1
not supplied
1
4-231-683-11 PANEL, LOADING
2
4-210-291-01 SCREW (CASE 3 TP2)
3
4-231-686-11 CASE (409538)
#1
7-685-646-79 SCREW +BVTP 3X8 TYPE2 N-S
Click on the first or last page to see other CDP-CE575 service manuals if exist.