Sony BDV-E780W / BDV-E980W / BDV-E985W / HBD-E780W / HBD-E980W / HBD-E985W Service Manual ▷ View online
HBD-E780W/E980W/E985W
25
6. Diag (Audio Input Test)
This screen performs audio input test.
This screen performs audio input test.
Screen 1: Select Audio Input Test Category
Operation:
[
Operation:
[
<]/[,] Selects the category
[
m]/[ ]
Activate the selected category
[RETURN] Returns to the service top menu
Screen 2: Select Input Device
After “Audio Input Test” selects in Screen 1, the device to test is
chosen.
Operation:
[
After “Audio Input Test” selects in Screen 1, the device to test is
chosen.
Operation:
[
M]/[m] Selects
Device
[
]
Activate and Start Test/Stop
[RETURN] Returns to the selection of test category
•
Device Test
: Device List
Digital Input1
: CXD9998 is inputted from ARC
Digital Input2
: CXD9998 is inputted from Optical
Analog Input
: CXD9998 is inputted from AUDIO
• Audio
Input
Test
CXD9998 is inputted from DIR/analog and outputs LineOut (8ch)
L and R.
Check tone sound by speaker connected with LineOut (8ch) L and
R.
(Input; LPCM 48kHz 2ch)
L and R.
Check tone sound by speaker connected with LineOut (8ch) L and
R.
(Input; LPCM 48kHz 2ch)
Diag
Category:
Diag
Category: Audio Input Test
Device:
Device:
[ENT] Start Input Sound
HELP: [LEFT] [RIGHT] [UP] [DOWN] [ENT] [RET]
Audio Input Test
Digital Input 1
Digital Input 2
Analog Input
(Screen 1)
(Screen 2)
[ ]
Diag
Category: Audio Input Test
Device:
Device:
[ENT] Stop Input Sound
HELP: [LEFT] [RIGHT] [UP] [DOWN] [ENT] [RET]
[ ]
Digital Input 1
Digital Input 2
Analog Input
7. Diag (Wireless LAN Test) (HBD-E780W/E980W only)
This screen performs wireless LAN test.
This screen performs wireless LAN test.
Note: This mode doesn’t operate correctly. Never use this mode. Refer to
“CHECKING METHOD OF NETWORK OPERATION” on page
9 when you confi rm the wireless LAN operation.
9 when you confi rm the wireless LAN operation.
8. Diag (MIC Input Test)
This screen performs MIC input test.
This screen performs MIC input test.
Note: Not used for the servicing.
9. Diag (HDMI Input Test)
This screen performs HDMI input test.
This screen performs HDMI input test.
Screen 1: Select HDMI Input Test Category
Operation:
[
Operation:
[
<]/[,] Selects the category
[
m]/[ ]
Activate the selected category
[RETURN] Returns to the service top menu
Screen 2: Select Input Device
After “HDMI Input Test” selects in Screen 1, the device to test is
chosen.
Operation:
[
After “HDMI Input Test” selects in Screen 1, the device to test is
chosen.
Operation:
[
M]/[m] Selects
Device
[
]
Activate and Start Test/Stop
[RETURN] Returns to the selection of test category
•
Device Test
: Device List
HDMI Input1
: CXD9998 is inputted from HDMI1
HDMI Input2
: CXD9998 is inputted from HDMI2
• HDMI
Input
Test
Path test from HDMI to HDMI through CXD9998.
CXD9998 is selected and inputted HDMI IN and outputs HDMI
OUT.
Check Video and Audio by TV/AMP connected with HDMI.
CXD9998 is selected and inputted HDMI IN and outputs HDMI
OUT.
Check Video and Audio by TV/AMP connected with HDMI.
Diag
Category:
Diag
Category: HDMI Input Test
HELP: [UP] [ENT] [RET]
HDMI Input Test
[1] HDMI Input1 Test
[2] HDMI Input2 Test
[2] HDMI Input2 Test
The video and audio connected with
HDMI1 or HDMI2 are outputted to TV monitor
HDMI1 or HDMI2 are outputted to TV monitor
(Screen 1)
(Screen 2)
[ ]
HELP: [LEFT] [RIGHT] [UP] [DOWN] [ENT] [RET]
[ ]
10. Diag (Transcoder Test)
Note: Not used for the servicing.
Ver. 1.2
HBD-E780W/E980W/E985W
26
11. Log: Error Log (Output of each Log)
This screen displays the contents of each log.
This screen displays the contents of each log.
Note: Do not refer to the displayed date.
Screen 1: Selects log
Operation:
[1]/[
Operation:
[1]/[
]
Moves to the Error Log output screen
[RETURN] Returns to the top menu of the service mode
Screen 2: Displays the Error Log
Operation:
[
Operation:
[
<
]
Returns to the previous page
[
,
]
Moves to the next page
[RETURN] Returns to the screen (Screen 1) that selects the log
type
[RED]
Writes the log contents to an USB memory device
•
Viewing the log display
Error Log:
08/01/01 00: 53: 19: [ErrCode: 080400000000]
[Date] [Time] [Error code]
About copying log to USB memory device:
Press the [RED] button in each log display screen with the USB
memory device inserted into the unit.
Press the [RED] button in each log display screen with the USB
memory device inserted into the unit.
Note: Please do not press the [RED] button immediately after USB mem-
ory is inserted.
Please do not pull out USB memory immediately after the [RED]
button was pressed.
Error Log:
When
When
“getErrLogFile.trm
fi le” exists in the USB memory de-
vice, errlog.log fi le is output.
Select Log
HELP : [DOWN][ENT][(NUM)]
Error Log
08/01/01 00: 53: 19: [ErrCode: 080400000000]
08/01/01 00: 53: 45: [ErrCode: 080400252100]
08/01/01 00: 54: 00: [ErrCode: 080400005555]
08/01/01 00: 53: 45: [ErrCode: 080400252100]
08/01/01 00: 54: 00: [ErrCode: 080400005555]
:
:
:
[1] Error Log
(Screen 1)
(Screen 2)
12. Factory Initialize (Factory Settings)
There is a possibility that this mode cannot be correctly execut-
ed. Never use this mode.
ed. Never use this mode.
13. Network (Network Test Diagnosis Screen: Ifconfi g)
Network menu for the wired ethernet.
Network menu for the wired ethernet.
Screen 1: Ifconfi g Test
Operation:
[
Operation:
[
] Activate Ifconfi g (Display network setting)
[
,]
Select ping test
[RETURN] Returns to the top menu of the service mode
Screen 2: Ping Test
Operation:
[
Operation:
[
<
] Select
Ifconfi g test
[RETURN] Returns to the top menu of the service mode
(The details of a Ping test are “14. Network (Network Test Diagno-
sis Screen: Ping)”)
(The details of a Ping test are “14. Network (Network Test Diagno-
sis Screen: Ping)”)
Screen 3: Ifconfi g Test Active
Display Ifconfi g command results.
Operation:
[
Display Ifconfi g command results.
Operation:
[
] Ifconfi g retry
[
,] Select
Ping Test
[RETURN] Returns to the top menu of the service mode
Network
Test:
Ifconfig
Ping
HELP : [DOWN][ENT][(NUM)]
(Screen 1)
Network
HELP : [DOWN][ENT][(NUM)]
Network
(Screen 2)
(Screen 3)
Test: Ifconfig
Ping
[START]
Ping To:
Test:
Ifconfig
Ping
IP 192. 168. 11. 2 MAC 00-16-01-85-21-A3
HELP : [ENT]: Re/Exe [RIGHT]
HBD-E780W/E980W/E985W
27
14. Network (Network Test Diagnosis Screen: Ping)
Ping test for the wired ethernet.
Ping test for the wired ethernet.
Screen 1: Ping Test
Operation:
[
Operation:
[
<
] Select
Ifconfi g test
[
m
]
Ping execution preparation
[RETURN] Returns to the top menu of the service mode
Screen 2: The IP address of the Ping point is set up
(IP address input mode)
When “Ping to :>” is reversed, the [
] button is pressed and IP
is inputted.
Operation:
[
Operation:
[
]
Finish to input
[RETURN] Finish to input
[
[
<
]
Finish to input and Select Ifconfi g Test
[0] to [9]
Input Character sting ‘0-9’
[TIME]
Input Character sting ‘.’
[CLEAR] Backspace
Screen 3: Ping Test Active
When [START] is reversed, the [
When [START] is reversed, the [
] button is pressed and execute
ping.
Operation:
[
Operation:
[
]
Activate ping test
[
M
]
The IP address of the ping point is set up
[RETURN] Returns to the top menu of the service mode
(Screen 1)
Test:
(Screen 2)
Ping
Network
Test: Ifconfig
Ping to :> 192. 168. 200. 13
[ENT] : Release
[RET] : Release
[RET] : Release
(Screen 3)
Network
Ping to : 192. 168. 200. 13
[START]
HELP: [ENT] : Start [UP] [LEFT]
Ping
Ifconfig
Ping To :
[START]
Network
Test: Ifconfig
PING 192. 168. 200. 13 OK!
Ping
15. System Information (System Information Display)
This screen displays system information.
This screen displays system information.
Screen 1: Basic Information
Operation:
[
Operation:
[
,
]
Drive information (delta IOP of a drive is measured)
and wireless device information displayed (go to
Screen 2)
and wireless device information displayed (go to
Screen 2)
[RETURN] Returns to the top menu of the service mode
Screen 2: Drive and Wireless Information Menu
Operation:
[
Operation:
[
<
]
Basic Information displayed (go to Screen 1)
[RETURN] Returns to the top menu of the service mode
When delta IOP is measured, it becomes impossible to use the Ver-
sion Up function.
sion Up function.
Contents List:
Model
Destination
Sequence Number
MAC
IP
IFCON IFCON
Model
Destination
Sequence Number
MAC
IP
IFCON IFCON
Version
Bootloader Bootloader
Version
Host Main
Host Main Version
Host Sub
Host Sub Version
Middleware Middleware
Version
ADSP ADSP
Version
2nd DSP
2nd DSP Version
IF Model
IF Dest
IF Dest
WLAN module Serial
WLAN module hw Version
WLAN module MAC Address
Drive Firm Revision
CD DIOP
WLAN module hw Version
WLAN module MAC Address
Drive Firm Revision
CD DIOP
Delta IOP
DVD DIOP
Delta IOP
BD DIOP
Delta IOP
CD LD TIME
LD Time
DVD LD TIME LD Time
BD LD TIME
BD LD TIME
LD Time
HBD-E780W/E980W/E985W
28
System Information
Sequence Number :
MAC :
MAC :
Model :
Destination :
Destination :
IP :
IF-con Block0 Version :
Block1 Version :
Bootloader Version :
Host Main Version :
Host Sub Version :
Middleware Version :
ADSP Version :
Host Main Version :
Host Sub Version :
Middleware Version :
ADSP Version :
2nd DSP Version :
IF_MODEL :
IF_DEST :
IF_DEST :
HELP: [RET] [RIGHT]
(Screen 1)
System Information
DVD DIOP :
BD DIOP :
BD DIOP :
Drive Firm Revision :
CD DIOP :
CD DIOP :
WLAN module MAC Address :
WLAN module Serial :
WLAN module hw Version :
WLAN module hw Version :
CD LD TIME :
DVD LD TIME :
BD LD TIME :
DVD LD TIME :
BD LD TIME :
HELP: [RET] [LEFT]
(Screen 2)
16. Drive
This menu is used to operate the drive using drive-related diagnos-
tic and tools.
This menu is used to operate the drive using drive-related diagnos-
tic and tools.
Screen 1: Selecting items under *Drive
Operation:
[
Operation:
[
<
]/[
,
] Selects the category
[
m
]/[
]
Activate the selected category
[RETURN] Returns to the top menu of the service mode
[1] Drive OP data Write
[2] Servo Parameter Check Menu (Not used)
[3] Servo Signal Check Menu (Not used)
[4] S-Curve Check Menu (Not used)
[5] Readability Check Menu (Not used)
[6] OP Position Check Menu (Not used)
[7] OP Check Menu (Not used)
[8] Load Eject Aging (Not used)
[9] Spindle Control Check Menu (Not used)
[10] FA Test Mode (Not used)
[1] Drive OP data Write
[2] Servo Parameter Check Menu (Not used)
[3] Servo Signal Check Menu (Not used)
[4] S-Curve Check Menu (Not used)
[5] Readability Check Menu (Not used)
[6] OP Position Check Menu (Not used)
[7] OP Check Menu (Not used)
[8] Load Eject Aging (Not used)
[9] Spindle Control Check Menu (Not used)
[10] FA Test Mode (Not used)
Screen 2: To start OP data Write
Operation:
[
Operation:
[
] Starts
Screen 3: Show OP data Write result
Operation:
NG - USB is not fi nd
NG - File (Butada.txt) is not fi nd
OK - OP data write
Operation:
NG - USB is not fi nd
NG - File (Butada.txt) is not fi nd
OK - OP data write
• Drive
Test
For drive operating check. Service is only use Drive OP data write
to rewrite OP data after change of new CPU.
to rewrite OP data after change of new CPU.
Drive
[1] Drive OP data Write
Drive OP data Write
Insert USB StorageDevice ...
Remove DISC and Close tray.
Remove DISC and Close tray.
HELP: [ENT] [RET]
[ENT] Start
(Screen 1)
(Screen 2)
(Screen 3)
HELP: [ENT] [RET]
Drive OP data Write
Insert USB StorageDevice ...
Remove DISC and Close tray.
Remove DISC and Close tray.
NG - USB is not find
NG - File(Butada.txt) is not find
OK - OP data write
NG - File(Butada.txt) is not find
OK - OP data write
[ENT] Start
Click on the first or last page to see other BDV-E780W / BDV-E980W / BDV-E985W / HBD-E780W / HBD-E980W / HBD-E985W service manuals if exist.