Sony AIR-SA17TI Service Manual ▷ View online
AIR-SA17Ti
5
2-3. TX-IF BOARD, HOLDER (SAIR)
Note: This illustration sees the panel top block from TX-IF board side.
2-4. MAIN BOARD
Note: This illustration sees the panel top block from MAIN board side.
2 connector
(CN603)
7 holder (SAIR)
5 TX-IF board
3
4 cushion (remote PWB)
1 two screws
(BVTP2.6
(3CR))
6 two screws
(BVTP2.6
(3CR))
panel top block
0 MAIN board
4 flexible flat cable (9 core)
(CN402)
3 insulating sheet (PWB main)
8 escutcheon
panel top block
9 sheet (FL)
2
6 flexible flat cable (9 core)
(W002)
1 six screws
(BVTP2.6
(3CR))
5 Remove the solders.
7 sheet (HS)
AIR-SA17Ti
6
SECTION 3
TEST MODE
1. PANEL TEST
Procedure:
1. The [POWER] switch is set [ON] to turn the main power on.
2. While pressing the [S-AIR MODE] and [SYSTEM MENU]
Procedure:
1. The [POWER] switch is set [ON] to turn the main power on.
2. While pressing the [S-AIR MODE] and [SYSTEM MENU]
buttons, press the [PAIRING] button.
3. Then all segments of fl uorescent indicator tube are turned on
and all LEDs are lighted.
4. Press the [SYSTEM MENU] button, the model name is dis-
played on the fl uorescent indicator tube.
5. Each time [SYSTEM MENU] button is pressed, the display
changes starting from model name, destination, MC, SYS, UI,
ST and AR version this order, and returns to the model name
display.
ST and AR version this order, and returns to the model name
display.
6. Press the [ILLUMINATION] button, the version is displayed
changes to last updated date displayed.
7. Press the [S-AIR MODE] button, the messages “K 0” is
displayed on the fl uorescent indicator tube. All buttons are
pressed, display becomes “K 7”.
pressed, display becomes “K 7”.
8. To release from this mode, while pressing the [S-AIR MODE]
and [SYSTEM MENU] buttons, press the [PAIRING] button.
2. FACTORY PRESET
Procedure:
1. The [POWER] switch is set [ON] to turn the main power on.
2. While pressing the [S-AIR MODE] and [TUNING/SELECT
Procedure:
1. The [POWER] switch is set [ON] to turn the main power on.
2. While pressing the [S-AIR MODE] and [TUNING/SELECT
–] buttons, press the [PAIRING] button.
3. The messages “TUNER” appears and initialization is per-
formed, and the messages “FM 87.50” appears.
3. S-AIR TEST
3-1. S-AIR test mode
Setting method:
1. The [POWER] switch is set [ON] to turn the main power on.
2. While pressing the [S-AIR MODE] and [TUNING/SELECT
3-1. S-AIR test mode
Setting method:
1. The [POWER] switch is set [ON] to turn the main power on.
2. While pressing the [S-AIR MODE] and [TUNING/SELECT
+] buttons, press the [PAIRING] button.
3. Entered the S-AIR test mode.
4. It returns to the S-AIR test mode each item when [SYSTEM
4. It returns to the S-AIR test mode each item when [SYSTEM
MENU] button is pressed after it enters each item.
5. To release from this mode, while pressing the [S-AIR MODE]
and [TUNING/SELECT +] buttons, press the [PAIRING] but-
ton.
ton.
3-1-1. Power setting
This mode is setting of radio wave output of EZW-RT10A.
Procedure:
1. Enter the S-AIR test mode.
2. Press the [TUNING/SELECT +]/[TUNING/SELECT –] but-
This mode is setting of radio wave output of EZW-RT10A.
Procedure:
1. Enter the S-AIR test mode.
2. Press the [TUNING/SELECT +]/[TUNING/SELECT –] but-
tons to select “POWER”.
3. Press the [ENTER] button the messages “000 SET” is dis-
played on the fl uorescent indicator tube.
4. Press the [TUNING/SELECT +]/[TUNING/SELECT –] but-
tons to select the radio wave output. (OFF or 000 to 063)
5. Press the [ENTER] button, return to S-AIR test mode each
item.
3-1-2. RF CH check
This mode is RF CH used is confi rmed.
Procedure:
1. Enter the S-AIR test mode.
2. Press the [TUNING/SELECT +]/[TUNING/SELECT –] but-
This mode is RF CH used is confi rmed.
Procedure:
1. Enter the S-AIR test mode.
2. Press the [TUNING/SELECT +]/[TUNING/SELECT –] but-
tons to select “CHK RFCH”.
3. Press the [ENTER] button the messages “*** CH#” is dis-
played on the fl uorescent indicator tube.
***: ON or OFF
#: CH number used
4. Press the [ENTER] button, return to S-AIR test mode each
item.
3-1-3. ENC key change
This mode is setting of code key on/off change of EZW-RT10A.
Procedure:
1. Enter the S-AIR test mode.
2. Press the [TUNING/SELECT +]/[TUNING/SELECT –] but-
This mode is setting of code key on/off change of EZW-RT10A.
Procedure:
1. Enter the S-AIR test mode.
2. Press the [TUNING/SELECT +]/[TUNING/SELECT –] but-
tons to select “ENC KEY”.
3. Press the [ENTER] button the messages “ON” or “OFF” is
displayed on the fl uorescent indicator tube.
4. Press the [TUNING/SELECT +]/[TUNING/SELECT –] but-
tons to select the “ON” or “OFF”.
5. Press the [ENTER] button, return to S-AIR test mode menu.
3-1-4. Version check
This mode is S-AIR version of the set connected with AIR-SA17Ti
is confi rmed.
Procedure:
1. Enter the S-AIR test mode.
2. Press the [TUNING/SELECT +]/[TUNING/SELECT –] but-
This mode is S-AIR version of the set connected with AIR-SA17Ti
is confi rmed.
Procedure:
1. Enter the S-AIR test mode.
2. Press the [TUNING/SELECT +]/[TUNING/SELECT –] but-
tons to select “VER. CHEC”.
3. Press the [ENTER] button, S-AIR version of the set connected
with AIR-SA17Ti is displayed on the fl uorescent indicator.
4. Press the [TUNING/SELECT +]/[TUNING/SELECT –] but-
tons, change the version and date displayed.
5. Press the [ENTER] button, return to S-AIR test mode each
item.
3-1-5. DARR setting check
This mode is setting of EZW-RT10A is confi rmed.
Procedure:
1. Enter the S-AIR test mode.
2. Press the [TUNING/SELECT +]/[TUNING/SELECT –] but-
This mode is setting of EZW-RT10A is confi rmed.
Procedure:
1. Enter the S-AIR test mode.
2. Press the [TUNING/SELECT +]/[TUNING/SELECT –] but-
tons to select “DARR”.
3. Press the [ENTER] button, main unit connect code is displayed
on the fl uorescent indicator.
4. Press the [TUNING/SELECT +]/[TUNING/SELECT –] but-
tons, change sub unit connection number, sub unit connect
code and sub unit address this order, and returns to the main
unit connect code display.
code and sub unit address this order, and returns to the main
unit connect code display.
CO ****: main unit connect code
MUCNT **: sub unit connectoin number
MUCO****: sub unit connect code
MUADR **: sub unit address
NAMG ***: NAMG setting value
5. Press the [ENTER] button, return to S-AIR test mode each
item.
AIR-SA17Ti
AIR-SA17Ti
7
7
3-1-6. Channel pipe setting
This mode is channel pipe is setting.
Procedure:
1. Enter the S-AIR test mode.
2. Press the [TUNING/SELECT +]/[TUNING/SELECT –] but-
This mode is channel pipe is setting.
Procedure:
1. Enter the S-AIR test mode.
2. Press the [TUNING/SELECT +]/[TUNING/SELECT –] but-
tons to select “CH1 PIPE” (or “CH2 PIPE”, “CH3 PIPE”,
“CH4 PIPE”).
“CH4 PIPE”).
3. Press the [ENTER] button, the messages “CH* - CH#” is dis-
played on the fl uorescent indicator tube.
*: channel number of selected step 2
#: number of channel pipe
4. Press the [TUNING/SELECT +]/[TUNING/SELECT –] but-
tons to select channel pipe setting.
5. Press the [ENTER] button, return to S-AIR test mode each
item.
3-1-7. NAMG setting
This mode is change of NAMG setting.
Procedure:
1. Enter the S-AIR test mode.
2. Press the [TUNING/SELECT +]/[TUNING/SELECT –] but-
This mode is change of NAMG setting.
Procedure:
1. Enter the S-AIR test mode.
2. Press the [TUNING/SELECT +]/[TUNING/SELECT –] but-
tons to select “NAMG”.
3. Press the [ENTER] button the messages “*** SET” is dis-
played on the fl uorescent indicator tube.
***: 107 to 117 or AUTO
4. Press the [TUNING/SELECT +]/[TUNING/SELECT –] but-
tons to select the NAMG setting value.
5. Press the [ENTER] button, return to S-AIR test mode each
item.
(This mode setting value is buck up even if it turns off power)
3-1-8. DEMO setting
This mode is radio wave does setting change to improve connec-
tion by batch processing in shop etc. when connection does not go
well badly.
Procedure:
1. Enter the S-AIR test mode.
2. Press the [TUNING/SELECT +]/[TUNING/SELECT –] but-
This mode is radio wave does setting change to improve connec-
tion by batch processing in shop etc. when connection does not go
well badly.
Procedure:
1. Enter the S-AIR test mode.
2. Press the [TUNING/SELECT +]/[TUNING/SELECT –] but-
tons to select “DEMO”.
3. Press the [ENTER] button the messages “ON” or “OFF” is
displayed on the fl uorescent indicator tube.
4. Press the [TUNING/SELECT +]/[TUNING/SELECT –] but-
tons to select the “ON” or “OFF”.
ON: batch processing on
OFF: batch processing off (default)
5. Press the [ENTER] button, return to S-AIR test mode each
item.
4. COLD RESET
Procedure:
1. The [POWER] switch is set [ON] to turn the main power on.
2. Press the [SYSTEM MENU] button, and press the [TUNING/
Procedure:
1. The [POWER] switch is set [ON] to turn the main power on.
2. Press the [SYSTEM MENU] button, and press the [TUNING/
SELECT +] button to select “RESET”.
3. Press the [ENTER] button twice.
4. The cold reset is executed.
4. The cold reset is executed.
SECTION 4
ELECTRICAL CHECK
FM TUNE LEVEL CHECK
signal
generator
set
Procedure:
1. Turn on the set.
2. Input the following signal from signal generator to FM antenna
1. Turn on the set.
2. Input the following signal from signal generator to FM antenna
input directly.
Carrier frequency : A = 87.5 MHz, B = 98 MHz, C = 108 MHz
Deviation
Deviation
: 75 kHz
Modulation
: 1 kHz
ANT input
: 35 dBu (EMF)
Note: Use 75 ohm coaxial cable to connect signal generator and the set.
You cannot use video cable for checking.
Use signal generator whose output impedance is 75 ohm.
3. Set to FM tuner function and tune A, B and C signals.
4. Confi rm “TUNED” is lit on the display for A, B and C signals.
4. Confi rm “TUNED” is lit on the display for A, B and C signals.
When the selected station signal is received in good condition,
“TUNED” is displayed.
“TUNED” is displayed.
AIR-SA17Ti
AIR-SA17Ti
8
8
SECTION 5
DIAGRAMS
For Schematic Diagrams.
Note:
• All capacitors are in μF unless otherwise noted. (p: pF) 50
• All capacitors are in μF unless otherwise noted. (p: pF) 50
WV or less are not indicated except for electrolytics and
tantalums.
tantalums.
• All resistors are in Ω and 1/4 W or less unless otherwise
specifi ed.
• f : internal component.
•
C : panel designation.
THIS NOTE IS COMMON FOR PRINTED WIRING BOARDS AND SCHEMATIC DIAGRAMS.
(In addition to this, the necessary note is printed in each block.)
(In addition to this, the necessary note is printed in each block.)
•
A : B+ Line.
•
B : B– Line.
• Voltages and waveforms are dc with respect to ground
under no-signal (detuned) conditions.
no mark : TUNER
• Voltages are taken with VOM (Input impedance 10 M
• Voltages are taken with VOM (Input impedance 10 M
Ω).
Voltage variations may be noted due to normal production
tolerances.
• Waveforms are taken with a oscilloscope.
Voltage variations may be noted due to normal production
Voltage variations may be noted due to normal production
tolerances.
• Circled numbers refer to waveforms.
• Signal path.
F :
TUNER
f
: iPod/iPhone (AUDIO)
E
: iPod/iPhone (VIDEO)
For Printed Wiring Boards.
Note:
•
•
X : Parts extracted from the component side.
•
Y : Parts extracted from the conductor side.
• f : Internal component.
•
: Pattern from the side which enables seeing.
(The other layers' patterns are not indicated.)
• Indication of transistor.
C
B
These are omitted.
E
Q
C E
B
These are omitted.
Caution:
Pattern face side:
(SIDE B)
Parts face side:
(SIDE A)
Pattern face side:
(SIDE B)
Parts face side:
(SIDE A)
Parts on the pattern face side seen
from the pattern face are indicated.
Parts on the parts face side seen from
the parts face are indicated.
from the pattern face are indicated.
Parts on the parts face side seen from
the parts face are indicated.
Caution:
Pattern face side:
(Conductor Side)
Parts face side:
(Component Side)
Pattern face side:
(Conductor Side)
Parts face side:
(Component Side)
Parts on the pattern face side seen
from the pattern face are indicated.
Parts on the parts face side seen from
the parts face are indicated.
from the pattern face are indicated.
Parts on the parts face side seen from
the parts face are indicated.
• MAIN, TX-IF, LED, LED-L and LED-R boards are multi-layer
printed boards.
However, the patterns of intermediate-layers have not been
included in diagrams.
• Circuit Boards Location
POWER board
MAIN board
tuner (FM)
LED-R board
LED board
TX-IF board
LED-L board
Note: The components identifi ed by mark
0 or dotted
line with mark
0 are critical for safety.
Replace only with part number specifi ed.
Click on the first or last page to see other AIR-SA17TI service manuals if exist.