Sharp LC-80LE657EN (serv.man5) User Manual / Operation Manual ▷ View online
15
Initial auto installation
When the TV is powered on for the first time after
purchase, the initial auto installation wizard appears.
Follow the menus and make the necessary settings
one after another.
purchase, the initial auto installation wizard appears.
Follow the menus and make the necessary settings
one after another.
Confirm the following before turning on
the power
the power
E
Is the antenna cable connected?
E
Is the AC cord plugged in?
1
Press a on the TV.
• The initial auto installation wizard appears.
2
Setting the OSD language.
Press
a/b/c/d to select the desired language, and
then press
;.
3
Selecting the location of the TV.
HOME
STORE
Press
c/d to select where you will use this TV, and
then press
;.
• The confirmation screen pops up only when
selecting “STORE”. Press
c/d to select “Yes” or
“No”.
• HOME: “STANDARD” will be the default value for
the “AV mode” setting.
• STORE: “DYNAMIC (Fixed)” will be the default
value for the “AV mode” setting. If the “AV mode”
is changed, the TV will automatically switch back
to “DYNAMIC (Fixed)” when there is no operation
using the TV or remote control unit for 30 minutes.
is changed, the TV will automatically switch back
to “DYNAMIC (Fixed)” when there is no operation
using the TV or remote control unit for 30 minutes.
• STORE: A demonstration image will be displayed
after initial auto installation is completed. If you
have chosen “STORE” by mistake, go to “TV
Menu” > “Setup” > “View setting” > “Reset” >
select “HOME” again.
have chosen “STORE” by mistake, go to “TV
Menu” > “Setup” > “View setting” > “Reset” >
select “HOME” again.
4
Setting the country.
Press
a/b/c/d to select your country or area, and
then press
;.
• This setting screen only appears during the initial
auto installation.
NOTE
• Some functions may not display or be selectable
depending on the country setting or cable provider
selection.
selection.
5
Setting the PIN.
1
Press
c/d to select “Yes”, and then press
;.
• When “No” is selected, the PIN code setting is
skipped.
2
Enter a four-digit number as a PIN using the
0–9 buttons.
0–9 buttons.
3
Enter the same four-digit number as in step
2 to confirm.
4
Press
;.
NOTE
• When “France” or “Italy” is selected in the country
setting, the PIN code setting cannot be skipped.
• “0000” cannot be set as the PIN code.
• When the PIN code setting is skipped, the default PIN
• When the PIN code setting is skipped, the default PIN
code (“1234”) will automatically be set.
• To change the PIN setting, refer to Individual setting —
PIN
(Page 44). To reset the PIN setting (PIN input will no
longer be needed), refer to Reset the PIN (Page 79).
6
Starting channel search.
Digital search
Analogue search
Satellite search
Press
a/b to select “Digital search”, “Analogue
search” or “Satellite search”, and then press
;.
• After performing “Digital search” or “Analogue
search”, the screen switches to the “Satellite
search” setting. You should then execute “Yes” if
you want to search for satellite channels.
search” setting. You should then execute “Yes” if
you want to search for satellite channels.
• To watch both digital broadcasts and analogue
broadcasts, you should perform “Digital search” or
“Analogue search” from “Auto installation” under
the “Setup” menu (Page 41).
“Analogue search” from “Auto installation” under
the “Setup” menu (Page 41).
• When you select “Satellite search”, only satellite
broadcasts will be searched.
• If you want to search for more broadcasts, execute
“Additional search” from the “Programme setup”
menu (Pages 41_43).
menu (Pages 41_43).
NOTE
• If you turn off the power on the TV while performing a
channel search, the initial auto installation wizard will
not appear. The auto installation function allows you
to execute the installation again from “TV Menu” >
“Setup” > “View setting” (Page 41).
not appear. The auto installation function allows you
to execute the installation again from “TV Menu” >
“Setup” > “View setting” (Page 41).
• The initial auto installation wizard will abort if you leave
the TV unattended for 30 minutes before searching for
channels.
channels.
• When “Italy” or “France” is selected in the country
setting, the default age restriction value is set to 18.
Initial auto installation
16
Digital broadcast setting
Press
c/d to select “Terrestrial” or “Cable”,
and then press
;.
Terrestrial
Cable
E
Searching for terrestrial broadcasts
The TV searches for, sorts and stores all the
receivable TV stations according to their settings
and the connected antenna.
receivable TV stations according to their settings
and the connected antenna.
• To abort the initial auto installation in progress,
press 6.
NOTE
• A region or service selection screen may display
depending on the country settings or cable providers
selections. Follow the screen prompts to make the
selections.
selections. Follow the screen prompts to make the
selections.
After searching for terrestrial channels, the screen
switches to the “Satellite search” setting (Page 17).
switches to the “Satellite search” setting (Page 17).
E
Searching for cable broadcasts
To change each item to the appropriate settings:
1
Press
a/b to select
the menu, and then
press
press
;.
2
Press
a/b/c/d or
0_9
to select or input
the appropriate item/
value, and then press
value, and then press
;.
Scrambled stations
[Yes]
Search method
[Channel]
Start frequency
Network ID
[None]
Symbol rate 1
Symbol rate 2
QAM modulation 1
QAM modulation 2
Reset
Search start
3
Press
a/b to select “Search start”, and then
press
;.
4
Press
c/d to select “Yes” to start searching
cable broadcasts, and then press
;.
5
The TV searches for, sorts and stores all the
receivable TV stations according to their settings
and the connected antenna.
receivable TV stations according to their settings
and the connected antenna.
• To abort the initial auto installation in progress,
press 6.
After searching for cable channels, the screen
switches to the “Satellite search” setting (Page 17).
switches to the “Satellite search” setting (Page 17).
Menu
Description
Selectable items
Scrambled
stations
stations
Specifies if you
need to add pay-
TV services.
need to add pay-
TV services.
Yes, No
Search method
Specifies how
you search for
channels.*
you search for
channels.*
2
Channel,
Frequency, Quick
Frequency, Quick
Start frequency
From 47.0_858.0
MHz
MHz
Network ID
Specifies the
network.*
network.*
3
None, 0_65535
Symbol rate 1/
Symbol rate 2*
Symbol rate 2*
1
Input the value
received for
CATV.*
received for
CATV.*
4
1000_9000
QAM
modulation 1
modulation 1
16, 32, 64, 128,
256
256
QAM
modulation 2
modulation 2
None, 16, 32, 64,
128, 256
128, 256
I
Set up “Symbol rate 2” if the cable provider uses
several symbol rates.
several symbol rates.
J
Details about the “Search method” items are as
follows:
_Channel: Extracts all information from a channel
(quick, but needs corresponding TV stations).
_Frequency: Checks every frequency in range (slow).
_Quick: All services are searched by one frequency.
This menu works only when your cable provider
provides the frequency and the network ID (e.g.,
Homing channel). When “Quick” is selected,
“Scrambled stations” is automatically set to “Yes”, and
“None” for the “Network ID” menu cannot be selected.
follows:
_Channel: Extracts all information from a channel
(quick, but needs corresponding TV stations).
_Frequency: Checks every frequency in range (slow).
_Quick: All services are searched by one frequency.
This menu works only when your cable provider
provides the frequency and the network ID (e.g.,
Homing channel). When “Quick” is selected,
“Scrambled stations” is automatically set to “Yes”, and
“None” for the “Network ID” menu cannot be selected.
K
Set this to register only the specified network ID
without registering any special services.
without registering any special services.
L
The symbol rates are specified by the cable provider.
Analogue broadcast setting
The TV searches for, sorts and stores all the
receivable TV stations according to their settings
and the connected antenna.
receivable TV stations according to their settings
and the connected antenna.
• To abort the initial auto installation in progress,
press 6.
After searching for analogue channels, the screen
switches to the “Satellite search” setting (Page 17).
switches to the “Satellite search” setting (Page 17).
Initial auto installation
17
Searching for satellite broadcasts
Press
a/b to select “Satellite search”, and then
press
;.
Digital search
Analogue search
Satellite search
• The antenna connection setting screen is displayed.
Single satellite
2 satellites on toneburst switchbox
Max. 4 satellites on DiSEqC multiswitch
Communal satellite system
NOTE
• You can select the antenna connection method from the
four types. Consult your dealers before using a method
other than “Single satellite”.
other than “Single satellite”.
E
“Single satellite” setting
1
Press
a/b to select “Single satellite”, and then
press
;.
2
Press
a/b/c/d to select your favorite
satellite, and then press
;.
Euro Bird 1
Atlantic Bird 1
NOTE
• Follow the instructions on the screen for “2 satellites
on toneburst switchbox”, “Max. 4 satellites on DiSEqC
multiswitch” and “Communal satellite system” settings.
multiswitch” and “Communal satellite system” settings.
• To set multiple satellite channels, go to “Max. 4 satellites
on DiSEqC multiswitch”.
• When a power supply is needed for your satellite
antenna, follow the procedure below in order to supply
the voltage specified by your service provider, etc.:
Go to “TV Menu” > “Setup” > “View setting” > “Channel
settings” > “Antenna setup-DIGITAL” > “Satellite setup” >
“Change setting” > “Communal satellite system”.
the voltage specified by your service provider, etc.:
Go to “TV Menu” > “Setup” > “View setting” > “Channel
settings” > “Antenna setup-DIGITAL” > “Satellite setup” >
“Change setting” > “Communal satellite system”.
E
Search start:
DVB-S/S2 channel searching.
1
Press
c/d to select “Yes”, and then press ;.
• To change the settings for “Scrambled stations”,
press
a/b to select the item to be reconfigured
and then perform “Search start”.
Yes
No
Scrambled stations
Search start
Start search?
[Yes]
2
The TV searches for and stores all the receivable
TV stations according to their settings and the
connected antenna.
TV stations according to their settings and the
connected antenna.
• Select “Yes” to sort the search result in alphabetical
order.
• To abort the initial auto installation in progress,
press 6.
NOTE
• Scrambled stations: Specifies if you need to choose
pay-TV services.
• Follow the procedure to perform “Manual search” if you
want to configure the frequency or symbol rate and start
to search after performing the auto searching during the
initial auto installation.
to search after performing the auto searching during the
initial auto installation.
− Go to “TV Menu” > “Setup” > “View setting” >
“Channel settings” > “Programme setup” > “Satellite
setting” > “Manual search”.
setting” > “Manual search”.
Initial auto installation
18
Checking signal strength and
channel strength (DVB-T/T2/C/S/S2)
channel strength (DVB-T/T2/C/S/S2)
If you install a DVB-T/T2/C/S/S2 antenna for the first
time or relocate it, you should adjust the alignment
of the antenna to receive a good reception while
checking the antenna setup screen.
time or relocate it, you should adjust the alignment
of the antenna to receive a good reception while
checking the antenna setup screen.
1
Go to “TV Menu” > “Setup” > “View setting” >
“Channel settings” > “Antenna setup-DIGITAL”.
“Channel settings” > “Antenna setup-DIGITAL”.
2
Press
a/b to select “Digital setup” or “Satellite
setup”, and then press
;.
E
Checking signal strength
3
Press
a/b to select “Signal strength”, and then
press
;.
Signal strength for DVB-T/T2/C
Supply voltage
CH No.
Current
Max.
Signal strength
Signal strength
Channel strength
Current
Max.
Quality
Signal strength for DVB-S/S2
Current
Max.
Signal strength
Signal strength
Channel strength
Current
Max.
Quality
E
Checking channel strength
4
Press
a/b to select “Channel strength”, and
then press
;.
• You can input a specified frequency band using the
0_9
numeric buttons.
Channel strength of DVB-T/T2
Supply voltage
CH No.
Current
Max.
Signal strength
MHz
Signal strength
Frequency
Channel strength
Current
Max.
Quality
Channel strength of DVB-C
Supply voltage
Current
Max.
Signal strength
MHz
Signal strength
Frequency
Symbol rate
QAM modulation
Symbol rate
QAM modulation
Channel strength
Current
Max.
Quality
Channel strength of DVB-S/S2
Current
Max.
Signal strength
MHz
Signal strength
Frequency
Symbol rate
Band
Symbol rate
Band
Channel strength
Current
Max.
Quality
Vert/Low
5
Position and align the antenna so that the
maximum possible values for “Signal strength”
and “Quality” are obtained.
maximum possible values for “Signal strength”
and “Quality” are obtained.
NOTE
• The values of “Signal strength” and “Quality” indicate
when to check the appropriate alignment of the
antenna.
antenna.
Supplying power to the antenna
You must supply power to the antenna in order
to receive digitally/terrestrially broadcast stations
after connecting the antenna cable to the antenna
terminal on the rear of the TV.
to receive digitally/terrestrially broadcast stations
after connecting the antenna cable to the antenna
terminal on the rear of the TV.
1
Go to “TV Menu” > “Setup” > “View setting” >
“Channel settings” > “Antenna setup-DIGITAL” >
“Supply voltage”.
“Channel settings” > “Antenna setup-DIGITAL” >
“Supply voltage”.
2
Press
c/d to select “On”, and then press ;.
Initial auto installation
Click on the first or last page to see other LC-80LE657EN (serv.man5) service manuals if exist.