Sharp LC-70UQ10KN (serv.man4) User Manual / Operation Manual ▷ View online
15
Digital broadcast setting
Press c/d to select “Terrestrial” or “Cable”,
and then press ;.
Terrestrial
Cable
E
Searching for terrestrial broadcasts
The TV searches for, sorts and stores all the
receivable TV stations according to their settings
and the connected antenna.
• To abort the initial auto installation in progress,
press 6.
NOTE
• A region or service selection screen may display
depending on the country settings or cable providers
selections. Follow the screen prompts to make the
selections.
After searching for terrestrial channels, the screen
switches to the “Satellite search” setting (Page
16).
E
Searching for cable broadcasts
To change each item to the appropriate settings:
1
Press a/b to select
the menu, and then
press ;.
2
Press a/b/c/d or
0_9 to select or input
the appropriate item/
value, and then press
;.
Scrambled stations
[Yes]
Search method
[Channel]
Start frequency
Network ID
[None]
Symbol rate 1
Symbol rate 2
QAM modulation 1
QAM modulation 2
Reset
Search start
3
Press a/b to select “Search start”, and then
press ;.
4
Press c/d to select “Yes” to start searching
cable broadcasts, and then press ;.
5
The TV searches for, sorts and stores all the
receivable TV stations according to their settings
and the connected antenna.
• To abort the initial auto installation in progress,
press 6.
After searching for cable channels, the screen
switches to the “Satellite search” setting (Page
16).
Menu
Description
Selectable items
Scrambled
stations
Specifies if you
need to add pay-
TV services.
Yes, No
Search method
Specifies how
you search for
channels.*
2
Channel,
Frequency, Quick
Start frequency
From 47.0_858.0
MHz
Network ID
Specifies the
network.*
3
None, 0_65535
Symbol rate 1/
Symbol rate 2*
1
Input the value
received for
CATV.*
4
1000_9000
QAM
modulation 1
16, 32, 64, 128,
256
QAM
modulation 2
None, 16, 32, 64,
128, 256
I
Set up “Symbol rate 2” if the cable provider uses
several symbol rates.
J
Details about the “Search method” items are as
follows:
_
_
Channel: Extracts all information from a channel
(quick, but needs corresponding TV stations).
_
_
Frequency: Checks every frequency in range (slow).
_
Quick: All services are searched by one frequency.
This menu works only when your cable provider
provides the frequency and the network ID (e.g.,
Homing channel). When “Quick” is selected,
“Scrambled stations” is automatically set to “Yes”, and
“None” for the “Network ID” menu cannot be selected.
K
Set this to register only the specified network ID
without registering any special services.
L
The symbol rates are specified by the cable provider.
Analogue broadcast setting
The TV searches for, sorts and stores all the
receivable TV stations according to their settings
and the connected antenna.
• To abort the initial auto installation in progress,
press 6.
After searching for analogue channels, the screen
switches to the “Satellite search” setting (Page
16).
Initial auto installation
16
Searching for satellite broadcasts
Press a/b to select “Satellite search”, and then
press ;.
Digital search
Analogue search
Satellite search
• The antenna connection setting screen is displayed.
Single satellite
2 satellites on toneburst switchbox
Max. 4 satellites on DiSEqC multiswitch
Communal satellite system
NOTE
• You can select the antenna connection method from the
four types. Consult your dealers before using a method
other than “Single satellite”.
E
“Single satellite” setting
1
Press a/b to select “Single satellite”, and then
press ;.
2
Press a/b/c/d to select your favorite
satellite, and then press ;.
Euro Bird 1
Atlantic Bird 1
NOTE
• Follow the instructions on the screen for “2 satellites
on toneburst switchbox”, “Max. 4 satellites on DiSEqC
multiswitch” and “Communal satellite system” settings.
• To set multiple satellite channels, go to “Max. 4 satellites
on DiSEqC multiswitch”.
• When a power supply is needed for your satellite
antenna, follow the procedure below in order to supply
the voltage specified by your service provider, etc.:
Go to “TV Menu” > “Setup” > “View setting” > “Channel
settings” > “Antenna setup-DIGITAL” > “Satellite setup” >
“Change setting” > “Communal satellite system”.
E
Search start:
DVB-S/S2 channel searching.
1
Press c/d to select “Yes”, and then press ;.
• To change the settings for “Scrambled stations”,
press a/b to select the item to be reconfigured
and then perform “Search start”.
Yes
No
Scrambled stations
Search start
Start search?
[Yes]
2
The TV searches for and stores all the receivable
TV stations according to their settings and the
connected antenna.
• Select “Yes” to sort the search result in alphabetical
order.
• To abort the initial auto installation in progress,
press 6.
NOTE
• Scrambled stations: Specifies if you need to choose
pay-TV services.
• Follow the procedure to perform “Manual search” if you
want to configure the frequency or symbol rate and start
to search after performing the auto searching during the
initial auto installation.
− Go to “TV Menu” > “Setup” > “View setting” >
“Channel settings” > “Programme setup” > “Satellite
setting” > “Manual search”.
Initial auto installation
17
Checking signal strength and
channel strength (DVB-T/T2/C/S/S2)
If you install a DVB-T/T2/C/S/S2 antenna for the first
time or relocate it, you should adjust the alignment
of the antenna to receive a good reception while
checking the antenna setup screen.
1
Go to “TV Menu” > “Setup” > “View setting” >
“Channel settings” > “Antenna setup-DIGITAL”.
2
Press a/b to select “Digital setup” or “Satellite
setup”, and then press ;.
E
Checking signal strength
3
Press a/b to select “Signal strength”, and then
press ;.
Signal strength for DVB-T/T2/C
Supply voltage
CH No.
Current
Max.
Signal strength
Signal strength
Channel strength
Current
Max.
Quality
Signal strength for DVB-S/S2
Current
Max.
Signal strength
Signal strength
Channel strength
Current
Max.
Quality
E
Checking channel strength
4
Press a/b to select “Channel strength”, and
then press ;.
• You can input a specified frequency band using the
0_9 numeric buttons.
Channel strength of DVB-T/T2
Supply voltage
CH No.
Current
Max.
Signal strength
MHz
Signal strength
Frequency
Channel strength
Current
Max.
Quality
Channel strength of DVB-C
Supply voltage
Current
Max.
Signal strength
MHz
Signal strength
Frequency
Symbol rate
QAM modulation
Symbol rate
QAM modulation
Channel strength
Current
Max.
Quality
Channel strength of DVB-S/S2
Current
Max.
Signal strength
MHz
Signal strength
Frequency
Symbol rate
Band
Symbol rate
Band
Channel strength
Current
Max.
Quality
Vert/Low
5
Position and align the antenna so that the
maximum possible values for “Signal strength”
and “Quality” are obtained.
NOTE
• The values of “Signal strength” and “Quality” indicate
when to check the appropriate alignment of the
antenna.
Supplying power to the antenna
You must supply power to the antenna in order
to receive digitally/terrestrially broadcast stations
after connecting the antenna cable to the antenna
terminal on the rear of the TV.
1
Go to “TV Menu” > “Setup” > “View setting” >
“Channel settings” > “Antenna setup-DIGITAL” >
“Supply voltage”.
2
Press c/d to select “On”, and then press ;.
Initial auto installation
18
Daily operation
Switching on/off
Turning on/off the power
Press a on the TV or >a on the remote control
unit.
Standby mode
From standby, press a on the TV or >a on the
remote control unit.
NOTE
• If you are not going to use this TV for a long period of
time, be sure to remove the AC cord from the AC outlet.
• Weak electric power is still consumed even when the TV
is turned off.
Switching between digital, satellite
and analogue broadcasts
Watching digital
broadcasts
Watching analogue
broadcasts
Watching satellite
broadcasts
NOTE
• If multiple satellite services are set, each time you press
the
SAT button the channel switches as follows.
SAT1
SAT2
SAT3
SAT4
Changing channels
With :r/s
With 0_9
Selecting an external video source
Once the connection is made, press b to display
the “INPUT” screen, and then press b or a/b to
switch over to the appropriate external source with
;.
TV
INPUT
Switchable
CH list
NOTE
• You can also select an external video source from
“HOME” > “Input change”.
• Only HDMI inputs which are not set for “Input skip”
(Page 46) and properly connected inputs can be selected.
Watching TV
Click on the first or last page to see other LC-70UQ10KN (serv.man4) service manuals if exist.