Sharp LC-70UQ10KN (serv.man4) User Manual / Operation Manual ▷ View online
3
Introduction
Caring for the front panel
• Turn off the main power and unplug the AC cord from the wall outlet before handling.
• Gently wipe the surface of the front panel with a soft cloth (cotton, flannel, etc.). To
• Gently wipe the surface of the front panel with a soft cloth (cotton, flannel, etc.). To
protect the front panel, do not use a dirty cloth, liquid cleaners, or a chemical cloth
(wet/dry sheet type cloth, etc.). This may damage the surface of the front panel.
• Wiping with a hard cloth or using strong force may scratch the surface of the front
panel.
• Use a soft damp cloth to gently wipe the front panel when it is really dirty (It may
scratch the surface of the front panel when wiped strongly).
• If the front panel is dusty, use an anti-static brush, which is commercially available, to
clean it.
WARNING
To prevent the spread of fire, keep candles or other open flames
away from this product at all times.
3D glasses
Prevention of accidental ingestion
• Keep the accessory out of the reach of small children. Small children can accidentally
swallow these parts.
• If a child accidentally swallows any of these parts, seek immediate medical attention.
Do not disassemble
• Do not disassemble or modify the 3D glasses except when recycling the batteries.
Do not modify the 3D glasses.
Caution for lithium battery
• Batteries must not be exposed to excessive heat such as direct sunlight or fire.
• Replace only with the same or equivalent type of battery. The battery may explode if
• Replace only with the same or equivalent type of battery. The battery may explode if
improperly replaced.
• Take care not to reverse the battery poles (+ and –) when loading the battery. Follow
the correct procedure when loading the battery. Loading the battery incorrectly may
damage the battery or cause it to leak battery fluid, which could result in a fire, injury
or damage.
Handling the 3D glasses
• Do not drop, exert pressure on, or step on the 3D glasses. Doing so may damage the
glass section, which may result in injury.
• Be careful not to trap your finger in the hinge section of the 3D glasses. Doing so
may result in injury.
• Pay special attention when children are using this product.
Using the 3D glasses
• Do not drop, exert pressure on, or step on the 3D glasses. Doing so may damage the
glass section, which may result in the risk of injury.
• Use the 3D glasses only for the specified purpose.
• Do not move around while wearing the 3D glasses. The surrounding area appears
• Do not move around while wearing the 3D glasses. The surrounding area appears
dark, which may result in falling or other accidents that may cause injury.
Caring for the 3D glasses
• Use only the cloth provided with the 3D glasses to clean the lenses. Remove dust
and soil from the cloth. Any dust or other soiling on the cloth may result in scratches.
Do not use solvents such as benzene or thinners as doing so may damage the
coating.
• When cleaning the 3D glasses, take care not to allow water or other fluids to come
into contact with the glasses.
• Always store the 3D glasses in the case provided when not in use.
• When storing the 3D glasses, avoid very humid or hot locations.
• When storing the 3D glasses, avoid very humid or hot locations.
Viewing 3D images
• If you experience dizziness, nausea, or other discomfort while viewing 3D images,
discontinue use and rest your eyes.
• Do not use the 3D glasses if they are cracked or broken.
4
Supplied accessories
Remote control unit ( x 1)
“AAA” size battery ( x 2)
Pages 6 and 8
Page 6
Stand unit ( x 1)
Page 5
3D glasses
(x 2)
AC cord ( x 1)
(For 80 inch models only)
Page 67
Page 9
Initial setup guide
(printed document)
Important safety
precautions
(printed document)
Optional accessories
The listed optional accessories are available for this LCD colour TV. Please
purchase them at your nearest shop.
• Additional optional accessories may be available in the near future. When purchasing,
please read the newest catalogue for compatibility and check the availability.
No.
Part name
Part
number
Notes
1
Wall mount bracket
(For 60/70 inch models)
AN-52AG4 The mark “c” indicates the location of
the centre of the TV screen
.
2
3D glasses
AN-3DG40
Refer to the operation manual of 3D
glasses for details regarding usage.
Introduction
5
Attaching the stand unit
• Before attaching (or detaching) the stand, unplug the AC cord.
• Before performing work, spread cushioning over the
surface on which you will be laying the TV. This will
prevent it from being damaged.
• Be sure that two or more persons attach the stand.
CAUTION
•
Attach the stand in the correct direction.
•
Be sure to follow the instructions. Incorrect installation
of the stand may result in the TV falling over.
•
After attaching the stand to the TV, do not hold the
stand when you put up, set up, move or lay down the TV.
•
Do not remove the stand from the TV unless using a
wall mount bracket to mount it.
1
Confirm that there are
14 screws (twelve M5
screws and two M4 screws) supplied with the
stand unit.
2
Attach the supporting post to the stand base.
1
Insert the claws of the supporting post into
the stand base.
2
Secure the post and the base using the M5
screws (length: 14 mm) and a screwdriver.
3
Insert the stand into the openings on the bottom
of the TV (hold the stand so it will not drop from
the edge of the base area).
• Make sure that the stand is firmly inserted into the
TV. Improper installation may result in tilting of the
TV set.
Soft cushion
4
Insert and tighten the M5 screws (length: 14 mm)
into the holes on the rear of the TV.
M5 screws
5
Attaching the stand cover.
1
Insert the stand cover.
2
Insert and tighten the M4 screw (length:
8 mm) into the holes of the stand cover.
• Tighten the screw by pressing the bottom of the
stand base to the TV side.
M4 screw
NOTE
• To detach the stand unit, perform the steps in reverse
order.
• A screwdriver is not supplied with this product.
• In the installation procedure, be careful not to catch
your fingers between the TV set and the floor.
Preparation
M5 screws
Soft cushion
6
Using the remote control unit
Inserting the batteries
Before using the TV for the first time, insert the two supplied “AAA” size
batteries. When the batteries become depleted and the remote control unit fails
to operate, replace the batteries with new “AAA” size batteries.
1
Open the battery cover.
2
Insert the two supplied “AAA” size batteries.
• Place batteries with their terminals corresponding to the (e)
and (f) indications in the battery compartment.
3
Close the battery cover.
CAUTION
Improper use of batteries can result in chemical leakage or explosion. Be sure to
follow the instructions below.
• Do not mix batteries of different types. Different types of batteries have different
characteristics.
• Do not mix old and new batteries. Mixing old and new batteries can shorten the life of
new batteries or cause chemical leakage in old batteries.
• Remove batteries as soon as they have worn out. Chemicals that leak from batteries
can cause a rash. If you find any chemical leakage, wipe thoroughly with a cloth.
• The batteries supplied with this product may have a shorter life expectancy due to
storage conditions.
• If you will not be using the remote control unit for an extended period of time, remove
the batteries from it.
Note on disposing batteries
The batteries provided contain no harmful materials such as cadmium, lead or
mercury.
Regulations concerning used batteries stipulate that batteries may no longer be
thrown out with the household rubbish. Deposit any used batteries free of charge
into the designated collection containers set up at commercial businesses.
Angle of the remote control unit
Use the remote control unit by pointing it towards the remote control sensor.
Objects between the remote control unit and sensor may prevent proper
operation.
Cautions regarding the remote control unit
• Do not expose the remote control unit to shock. In
addition, do not expose the remote control unit to
liquids, and do not place in an area with high humidity.
• Do not install or place the remote control unit under
direct sunlight. The heat may cause deformation of the
unit.
• The remote control unit may not work properly if the
remote control sensor of the TV is under direct sunlight
or strong lighting. In such cases, change the angle of
the lighting or the TV, or operate the remote control unit
closer to the remote control sensor.
Preparation
5 m
Remote control sensor
Click on the first or last page to see other LC-70UQ10KN (serv.man4) service manuals if exist.