DOWNLOAD Sharp LC-70LE741E (serv.man15) Service Manual ↓ Size: 7.43 MB | Pages: 80 in PDF or view online for FREE

• Gently wipe the surface of the front panel with a soft cloth (cotton, flannel, etc.). To 

protect the front panel, do not use a dirty cloth, liquid cleaners, or a chemical cloth 

(wet/dry sheet type cloth, etc.). This may damage the surface of the front panel.

• Wiping with a hard cloth or using strong force may scratch the surface of the front 

panel.

• Use a soft damp cloth to gently wipe the front panel when it is really dirty (It may 

scratch the surface of the front panel when wiped strongly).

•  If the front panel is dusty, use an anti-static brush, which is commercially available, to 

clean it.

To prevent the spread of fire, keep candles or other open flames 

away from this product at all times.

Prevention of accidental ingestion
•  Keep the accessory out of the reach of small children. Small children can accidentally 

swallow these parts.
—If a child accidentally swallows any of these parts, seek immediate medical 

attention.

Do not disassemble
•  Do not disassemble or modify the 3D glasses.
Handling the 3D glasses
•  Do not drop, exert pressure on, or step on the 3D glasses. Doing so may damage the 

glass section, which may result in injury.

•  Be careful not to trap your finger in the hinge section of the 3D glasses. Doing so 

may result in injury.
—Pay special attention when children are using this product.

Using the 3D glasses
•  The 3D glasses vision should be limited. Security advisory establishes a maximum of 

3 hours visualization, and in any case no more than one show length, break included.

•  Use the 3D glasses only for the specified purpose.
•  Do not move around while wearing the 3D glasses. The surrounding area appears 

dark, which may result in falling or other accidents that may cause injury.

Caring for the 3D glasses
•  Use only the cloth provided with the 3D glasses to clean the lenses. Remove dust 

and soil from the cloth. Any dust or other soiling on the cloth may result in scratches 

on the product. Do not use solvents such as benzene or thinners as doing so may 

cause the coating to peel off.

•  When cleaning the 3D glasses, take care not to allow water or other fluids to come 

into contact with the glasses.

•  Always store the 3D glasses in the case provided when not in use.
•  When storing the 3D glasses, avoid very humid or hot locations.
Viewing 3D images 
•  If you experience dizziness, nausea, or other discomfort while viewing 3D images, 

discontinue use and rest your eyes.

•  Do not use the 3D glasses if they are cracked or broken.
Keep away from heat
•  Do not place the 3D glasses in a fire, near heat or in an area with high humidity. This 

product may cause a fire or injury from ignition or explosion of the built-in lithium ion 

polymer rechargeable battery.

Caution regarding rechargeable battery
•  Use the supplied USB cable to connect to a USB terminal of a 3D compatible 

SHARP TV when recharging. Recharging using other devices may lead to battery 

leakage, heat generation or explosion. 

Caution regarding the power supply
•  Use the supplied USB cable to connect to a USB terminal of a 3D compatible 

SHARP TV for supplying power. Supplying power using other devices may lead to 

heat generation or explosion.

•  During a thunderstorm, to avoid getting an electric shock, do not use 3D glasses that 

are power-supplied via USB, and unplug the USB cable from the USB terminal on the 

TV and the USB terminal on the 3D glasses.

Remote control unit ( x 1)

LR03 (“AAA” size alkaline) battery ( x 2)

Pages 6 and 8

Page 6

Stand unit ( x 1)

Wireless LAN USB adapter 

(WN8522D 7-JU) ( x 1)

Page 5

Page 58

Initial setup guide 

(printed document)

USB memory 

(operation manual)

Important safety 

precautions 

(printed document)

The listed optional accessories are available for this LCD colour TV. Please 

purchase them at your nearest shop.

•  Additional optional accessories may be available in the near future. When purchasing, 

please read the newest catalogue for compatibility and check the availability.

1

Wall mount bracket 

AN-52AG4

The centre of the TV screen is 8 mm 

below the mark “c” on the wall bracket.
For 60 inch models

The centre of the TV screen is 18 mm 

below the mark “e” on the wall bracket.

2

3D glasses

AN-3DG20 Refer to the operation manual of the 3D 

glasses for details regarding usage.

•  Before attaching (or detaching) the stand, unplug the AC cord.

•  Before performing work, spread cushioning over the 

surface on which you will be laying the TV. This will 

prevent it from being damaged.

•  Attach the stand in the correct direction.

•  Be sure to follow the instructions. Incorrect installation 

•  After attaching the stand to the TV, do not hold the 

•  Do not remove the stand from the TV unless using a 

 

Confirm that there are twelve screws (eight long 

screws and four short screws) supplied with the 

stand unit.

 

 

1

Set the supporting post for the stand unit 

onto the polystyrene foam.

2

Attach the stand base to the supporting post.

3

Insert and tighten the eight screws into the 

eight holes on the bottom of the stand base.

•  Hold the stand unit securely with one hand, and 

then tighten the screws.

Stand base

Long screws

Supporting post

 

Insert the stand into the openings on the bottom 

of the TV (hold the stand so it will not drop from 

the edge of the base area).

•  Make sure that the stand is firmly inserted into the 

TV. Improper installation may result in tilting of the 

TV set.

Soft cushion

 

Insert and tighten the four screws into the four 

holes on the rear of the TV.

Short screws

•  To detach the stand unit, perform the steps in reverse 

order.

•  A screwdriver is not supplied with this product.

•  In the installation procedure, be careful not to catch 

your fingers between the TV set and the floor.

Before using the TV for the first time, insert the two supplied LR03 (“AAA” size 

alkaline) batteries. When the batteries become depleted and the remote control 

unit fails to operate, replace the batteries with new LR03 (“AAA” size alkaline) 

batteries.

 

Open the battery cover.

 

Insert the two supplied LR03 (“AAA” size alkaline) 

batteries.

•  Place batteries with their terminals corresponding to the (e) 

and (f) indications in the battery compartment.

 

Close the battery cover.

Improper use of batteries can result in chemical leakage or explosion. Be sure to 

follow the instructions below.

•  Do not mix batteries of different types. Different types of batteries have different 

characteristics.

•  Do not mix old and new batteries. Mixing old and new batteries can shorten the life of 

new batteries or cause chemical leakage in old batteries.

•  Remove batteries as soon as they have worn out. Chemicals that leak from batteries 

can cause a rash. If you find any chemical leakage, wipe thoroughly with a cloth.

•  The batteries supplied with this product may have a shorter life expectancy due to 

storage conditions.

•  If you will not be using the remote control unit for an extended period of time, remove 

the batteries from it.

•  When replacing the batteries, use alkaline batteries instead of zinc-carbon ones.

The batteries provided contain no harmful materials such as cadmium, lead or 

mercury.

Regulations concerning used batteries stipulate that batteries may no longer be 

thrown out with the household rubbish. Deposit any used batteries free of charge 

into the designated collection containers set up at commercial businesses.

Use the remote control unit by pointing it towards the remote control sensor. 

Objects between the remote control unit and sensor may prevent proper 

operation.

5 m

Remote control sensor

•  Do not expose the remote control unit to shock. In 

addition, do not expose the remote control unit to 

liquids, and do not place in an area with high humidity.

•  Do not install or place the remote control unit under 

direct sunlight. The heat may cause deformation of the 

unit.

•  The remote control unit may not work properly if the 

remote control sensor of the TV is under direct sunlight 

or strong lighting. In such cases, change the angle of 

the lighting or the TV, or operate the remote control unit 

closer to the remote control sensor.