DOWNLOAD Sharp LC-52XL1E (serv.man10) Service Manual ↓ Size: 4.63 MB | Pages: 48 in PDF or view online for FREE

AC cord (

g1)

U.K. type 3-pin AC cord is only included 

with models LC-46XL1E, 

LC-52XL1E.

•  “AAA” size battery (

g2)..........Page 6

Cable clamp 

(Small

g2, Large g1)

Page 4

Cable tie (

g1)

Page 4

3 RCA to 15-pin 

D-sub adapter 

(

g1)

Page 10

•  Operation manual (This publication)

Stand unit 

(

g1)

Page 3

Before attaching (or detaching) stand, unplug the AC cord from the AC INPUT terminal.

NOTE
•  To detach the stand, perform the above steps in reverse 

order.

Confi rm that there are 10 screws (6 short screws 
and 4 long screws) supplied with the TV.

Attach the two supporting posts for the stand 
unit onto the base using the box for the stand 
unit as shown below.

  Insert each of the protrusions on the two supporting 

posts into the openings on the upper side of the 
base.

  Insert and tighten the 6 short screws with the hex 

key (supplied with the product) in the order of 

1, 2 

and 

3.

(Close-up of the upper side of the stand unit)

Hex key

Short screw

Hex key

Long screw

Soft cushion

1 Insert the stand into the openings on the 

bottom of the TV.

2 Insert and tighten the 4 long screws into the 

4 holes on the rear of the TV.

•  Remote control unit (

g1)..........Pages 6 and 7

(For Europe, except 

U.K. and Eire)

(For U.K. and Eire)

Page 4

LC-52XL1E_gb_a.indd   3

LC-52XL1E_gb_a.indd   3

2007/04/25   14:45:27

2007/04/25   14:45:27

Bundle the AC 
cord with the 
clamp (small).

Standard DIN45325 
plug (IEC 169-2)
75 

q coaxial cable

Connect the antenna cable from your antenna-/cable socket or the (room-/roof) antenna for antenna input terminal on the 
back of your TV set to receive digitally/terrestrially broadcast stations.
An indoor antenna can also be used under good reception conditions. Passive and active room antennas are offered 
commercially. In an active antenna its power is supplied via the antenna input terminal.
The supply voltage (5V) must be correspondingly set under “Supply voltage”. (Page 19)

The Ferrite Core should be permanently attached and never removed from the AC cord.

  Installing the LCD Colour TV requires special skill that should only be performed by qualifi ed service personnel. 

•  You can ask a qualifi ed service personnel about using an optional bracket to mount the TV to the wall.

AC cord

(For Europe, except 
U.K. and Eire)

Cable clamp (small)

Cable tie

Place the TV close to the 
AC outlet, and keep the 
power plug within reach.

Ferrite Core *

Cable 

clamp 

(large)

Bundle the 

cables with 

the clamp.

(For U.K. and 
Eire)

LC-52XL1E_gb_a.indd   4

LC-52XL1E_gb_a.indd   4

2007/04/25   14:45:31

2007/04/25   14:45:31

NOTE
•  Only if you use an 

active terrestrial 
antenna, select 
“yes (5V)” under 
“Supply voltage”. 
(Page 19)

AC INPUT terminal

OPC sensor

Remote control 

sensor

B (Standby/On) 
indicator

OPC indicator

a (Power button)

 button

i (

l/k) 

(Volume buttons) 

 (

s/r)

(Programme [channel] buttons) 

SLEEP indicator

EXT 2 (AV) terminal

EXT 3 terminals

Headphone jack

EXT 1 (RGB) terminal

EXT 5 (HDMI/AUDIO) terminals

Antenna input terminal
(DVB-T 5V=/80 mA)

OUTPUT (Audio) terminals

EXT 4 terminals

RS-232C terminal

COMMON INTERFACE slot

EXT 6 (HDMI) terminal

Blue illumination LED indicator

LC-52XL1E_gb_a.indd   5

LC-52XL1E_gb_a.indd   5

2007/04/25   14:45:32

2007/04/25   14:45:32

Improper use of batteries can result in chemical leakage or explosion. Be sure to follow the instructions below.
• Do not mix batteries of different types. Different types of batteries have different characteristics.
• Do not mix old and new batteries. Mixing old and new batteries can shorten the life of new batteries or cause 

chemical leakage in old batteries.

• Remove batteries as soon as they have worn out. Chemicals that leak from batteries can cause a rash. If you fi nd 

any chemical leakage, wipe thoroughly with a cloth.

• When replacing the batteries, use alkaline batteries instead of manganese ones.
• Do not overuse the light-up function by using LIGHT 

D button, doing so may shorten the battery life. Replace 

the batteries when the light on LCD window or light-up function become weak or blurry.

• Do not continue to use the remote control unit with batteries running low. This may 

result in error message or malfunction. Should this happen replace the batteries and 
leave it unused for a while. Otherwise, you may open the rear battery cover and press 
the RESET button. When you press the RESET button, your Universal remote control 
settings will be deleted.

• The remote control unit has a internal memory of external devices. In order not to lose the data, 

replace the batteries quickly. If the manufacturer code is initialised and lost, you can input the 
manufacturer code again. (See page 37.) 

• The batteries supplied with this product may have a shorter life expectancy due to storage conditions.
• If you will not be using the remote control unit for an extended period of time, remove the batteries from it.

30°

30°

Remote control 
sensor

Press and slide the battery cover to open it.

Insert two supplied “AAA” size batteries.

•  Place batteries with their terminals corresponding 

to the (

e) and (f) indications in the battery 

compartment.

Close the battery cover.

Before using the TV for the fi rst time, insert two “AAA” size batteries (supplied). When the batteries become 
depleted and the remote control unit fails to operate, replace the batteries with new “AAA” size batteries.

• Do not expose the remote control unit to shock.
  In addition, do not expose the remote control unit to liquids, and do not place in an 

area with high humidity.

• Do not install or place the remote control unit under direct sunlight. The heat may 

cause deformation of the unit.

• The remote control unit may not work properly if the remote control sensor of the 

TV is under direct sunlight or strong lighting. In such case, change the angle of the 
lighting or TV, or operate the remote control unit closer to the remote control sensor.

5 m

Use the remote control unit by 
pointing it towards the remote 
control sensor. Objects between the 
remote control unit and sensor may 
prevent proper operation.

 button

LC-52XL1E_gb_a.indd   6

LC-52XL1E_gb_a.indd   6

2007/04/25   14:45:34

2007/04/25   14:45:34