DOWNLOAD Sharp LC-50LE751K (serv.man4) Service Manual ↓ Size: 17.24 MB | Pages: 64 in PDF or view online for FREE

Reception of a single satellite via a connected LNC 
(LNB).

Select satellite. 

Press 

J

 to continue.

 Select Dual Band (low/high) or Single Band. 

Here you specify if you use a Dual Band (Universal) 
LBN or Single LBN.

Press 

J

 to continue.

  Specify here the oscillator frequency for your LNB.

Normally you do not need to change the values 
for high and low band, unless the LNB of your 
satellite system uses a different oscillator frequency 
(important for the frequency display).
If you use the setting Single Band in step Dual/
Single Band, 

you only have to define the LNB 

frequency for the Low Band.

 Press 

J

 to continue.

See  Setting options for all DVB-S reception on 
page 13

 

to continue.

 Select 

 

  Select satellite name from list and press

Press

J

to continue.

  Specify here the oscillator frequency for your LNB.

Normally you do not need to change the values 
for high and low band, unless the LNB of your 
satellite system uses a different oscillator frequency 
(important for the frequency display).

 Press OK to select frequency and press 

J

  to 

continue.

See  Setting options for all DVB-S reception on 
page 13

 

to continue.

Select DiSEqC multiswitch and adpat settings for this 
selection.

  Select which DiSEqC single cable system you are 

using and press OK. 

  Select satellite name from list and press OK. Press 

J

to continue.

  Specify here the oscillator frequency for your LNB 

and press OK. Press 

J

to continue. 

Normally you do not need to change the values 
for high and low band, unless the LNB of your 
satellite system uses a different oscillator frequency 
(important for the frequency display).

  Select and adjust settings for DiSEqC single cable 

communal installation.

Select the desired transmission channel and the 
corresponding transmission frequency.

PIN protection
If your system is designed for it, it is possible to 
protect your used transmission data from use by 
other subscribers with a PIN.

Define/change PIN
Here you can determine and change the PIN for 
PIN protection

. Only possible when yes has been 

selected for PIN protection.

Continue with Setting options for all types of 
reception 

on page 13.

Press OK to adopt settings and press 

J

 to continue.

 Select 

to Satellite4. 

  Select satellite name from list and press OK.

Press 

J

 to continue.

  Specify here the oscillator frequency for your LNB.

Normally you do not need to change the values 
for high and low band, unless the LNB of your 
satellite system uses a different oscillator frequency 
(important for the frequency display).

See  Setting options for all DVB-S reception on 
page 13

 

to continue.

 

● 

 

The refresh rate determines how often a DiSEqC 
command is output. A refresh is only necessary with 
cascaded system.

● 

 

The control voltage controls the switch of the 
polarisation level (horizontal/vertical) in non-DiSEqC 
capable components (e.g., control of single LNBs 
via DiSEqC multiswitch).

● 

 

The 22kHz signal controls the switching between 
high and low band in the Band setting. The Position 
setting controls the selection of the satellites in non-
DiSEqC capable components.

● 

 

The Toneburst controls the selection of the satellites 
in non-DiSEqC but Toneburst capable components 
with the Position and Option settings.

 Select 

satellite.

 

Press

 J

 to continue.

  Specify here the oscillator frequency for your LNB.

 

If your set is connected to a single-cable system 

without external voltage supply, you can connect 
the antenna  supply (13V or 18V / max. 450mA) 
with 13V or 18V.

Continue with Setting options for DVB-S reception 
below.

● 

If several networks are available via DVB-S, you 
can decide which network you want to receive your 
channels from.

● 

If several satellites are received, the following settings 
must be made for every satellite. The type of settings 
available may differ depending on the selected satellite 
or network.

● 

Select yes to save all scrambled stations.
•  These stations can only be received in connection 

with a CI module and the appropriate CA Card.

•  If a CI module with a CA Card is already inserted 

for the station search, all the stations which this 
module can descramble are also saved when no 
is selected.

● 

If you select Frequency Search here, a search is 
performed for all receivable stations. With Network 
Search

, from all receivable networks all the stations are 

searched which are supplied by these networks.

● 

The symbol rate is specified by the satellite provider and 
normally does not need to be changed.

● 

This setting allows you to decide whether you want to 
accept the Logical Channel Number (LCN).
Press 

J

 to continue.

Continue with Setting options for all types of 
reception 

below.

● 

Allows you to restrict programmes depending on the age 
classification.

The information about age classification is provided by 
the broadcasting station. 
The stations locked can only be watched after entering 
the access code (see page 24).

● 

Enter the correct values with the numeric buttons here.

● 

● 

Here you can now specify if you wish to configure a 
network  "Configure now" (see page 47) or you wish 
to configure it later "Do not configure or configure 
later"

.

If you install a DVB-T/T2/S/S2 antenna for the first time 
or relocate it, you should adjust the alignment of the 
antenna to receive a good reception while checking the 
antenna setup screen.

In normal TV mode, without other displays, a DVB-T 
station is received and selected. 

 Select 

 Select 

Select Manual Scan TV. 

Position and align the antenna in such a manner that 
maximum values for C/N and Level are obtained.
The value for BER should be as low as possible.

Select Search and press OK to start search.