Sharp LC-45GD1E (serv.man45) User Manual / Operation Manual ▷ View online
10
Removing speakers
Preparation
NOTE
• To attach the speakers, perform the steps in reverse order.
• Perform the same steps for the left section of the speaker.
• Perform the same steps for the left section of the speaker.
CAUTION
• Do not remove the stand and speaker from the Display unless using an optional bracket to mount it.
• Before performing work spread cushioning over the base area to lay the Display on. This will prevent it from
• Before performing work spread cushioning over the base area to lay the Display on. This will prevent it from
being damaged.
1
2
3
4
Unfasten the screw used to secure the speaker
bracket.
bracket.
Unfasten the screws.
Take off the speaker terminal cover.
Disconnect the cable from the speaker.
LC-45GD1E(E)-a
04.9.27, 9:58 AM
10
11
Removing the stand
Before detaching (or attaching) stand, unplug the AC cord from the AC input terminal and the system cable
from the Display.
from the Display.
CAUTION
• Do not remove the stand from the Display unless using an optional wall mount bracket to mount it.
Before attaching/detaching stand
• Before performing work make sure to turn off the System.
• Before performing work spread cushioning over the base area to lay the Display on. This will prevent it from
• Before performing work spread cushioning over the base area to lay the Display on. This will prevent it from
being damaged.
NOTE
• To attach the stand, perform the above steps in reverse order.
2
Detach the stand from the Display.
(Hold the stand so it will not drop from the edge of
the base area.)
(Hold the stand so it will not drop from the edge of
the base area.)
1
Unfasten the four screws used to secure the
stand in place.
stand in place.
Setting the Display on the wall
CAUTION
• Installing the LCD Colour TV requires special skill that should only be performed by qualified service personnel.
Customers should not attempt to do the work themselves. SHARP bears no responsibility for improper mounting
or mounting that results in accident or injury.
or mounting that results in accident or injury.
Using an optional bracket to mount the Display
• You can ask a qualified service personnel about using the optional AN-37AG2 bracket to mount the Display
• You can ask a qualified service personnel about using the optional AN-37AG2 bracket to mount the Display
to the wall.
• Carefully read the instructions that come with the bracket before beginning work.
Hanging on the wall
AN-37AG2 wall mount bracket. (See the bracket instructions
for details.)
for details.)
About setting the Display angle
CAUTION
• Do not remove the stand and speaker from the Display unless using an optional bracket to mount it.
Vertical mounting
Angular mounting
10˚
Preparation
Angle of Display
With Speakers
Removed
With Speakers
Attached
10˚
0˚
LC-45GD1E(E)-b
04.9.27, 9:59 AM
11
12
Inserting the batteries
Before using the System for the first time, insert two “AAA” size batteries (supplied). When the batteries become
depleted and the remote control fails to operate, replace the batteries with new “AAA” size batteries.
depleted and the remote control fails to operate, replace the batteries with new “AAA” size batteries.
Using the remote control unit
Use the remote control unit by pointing it towards the remote sensor window.
Objects between the remote control unit and sensor window may prevent proper
operation.
Objects between the remote control unit and sensor window may prevent proper
operation.
Cautions regarding remote control unit
• Do not expose the remote control unit to shock.
In addition, do not expose the remote control unit to liquids, and do not place
in an area with high humidity.
in an area with high humidity.
• Do not install or place the remote control unit under direct sunlight.
The heat may cause deformation of the unit.
• The remote control unit may not work properly if the remote sensor window of
the Display is under direct sunlight or strong lighting. In such case, change
the angle of the lighting or Display, or operate the remote control unit closer to
the remote sensor window.
the angle of the lighting or Display, or operate the remote control unit closer to
the remote sensor window.
Preparation
1
Press and slide the battery cover to open it.
2
Insert two supplied “AAA” size batteries.
• Place batteries with their terminals corresponding to
the (e) and (f) indications in the battery
compartment.
compartment.
3
Close the battery cover.
CAUTION
Improper use of batteries can result in chemical leakage or explosion. Be sure to follow the instructions below.
• Do not mix batteries of different types. Different types of batteries have different characteristics.
• Do not mix old and new batteries. Mixing old and new batteries can shorten the life of new batteries or cause
• Do not mix batteries of different types. Different types of batteries have different characteristics.
• Do not mix old and new batteries. Mixing old and new batteries can shorten the life of new batteries or cause
chemical leakage in old batteries.
• Remove batteries as soon as they have worn out. Chemicals that leak from batteries can cause a rash. If you
find any chemical leakage, wipe thoroughly with a cloth.
• The batteries supplied with this product may have a shorter life expectancy due to storage conditions.
• If you will not be using the remote control unit for an extended period of time, remove the batteries from it.
• If you will not be using the remote control unit for an extended period of time, remove the batteries from it.
LC-45GD1E(E)-b
04.9.27, 9:59 AM
12
13
Preparation
Standard DIN45325 plug (IEC169-2)
75-ohm coaxial cable (round cable) (commercially available)
Simple operations for watching a TV programme
Basic connection
Connecting to an antenna
To enjoy a clearer picture, use an outdoor antenna. The following is a brief explanation of the types of connections
that are used for coaxial cable.
that are used for coaxial cable.
Antenna cables–commercially available
If your outdoor antenna uses a 75-ohm coaxial cable with a standard DIN45325
plug (IEC 169-2), plug it into the DIGITAL IN terminal at the rear of the AVC
System.
plug (IEC 169-2), plug it into the DIGITAL IN terminal at the rear of the AVC
System.
Connecting to the power outlet
Before connecting the AC cords, make sure to connect the system cable first.
Product shape varies
in some countries.
Antenna cable
(supplied)
For viewing only digital broadcasts, you do not need to connect the antenna
cable (supplied).
cable (supplied).
(ex. For viewing both analogue and digital broadcasts)
(ex. For viewing analogue broadcasts)
Display (rear view)
NOTE
• Always turn off the main power of Display when connecting the AC cords.
• Disconnect the AC cords from the AC outlet, Display and AVC System if the System will not be used for a long period of
• Disconnect the AC cords from the AC outlet, Display and AVC System if the System will not be used for a long period of
time.
AVC System (rear view)
Product shape varies
in some countries.
LC-45GD1E(E)-b
04.9.27, 9:59 AM
13
Click on the first or last page to see other LC-45GD1E (serv.man45) service manuals if exist.