Sharp LC-42XD1E (serv.man12) User Manual / Operation Manual ▷ View online
3
Confi rm that there are 8 screws (4 short screws
and 4 long screws) supplied with the TV.
and 4 long screws) supplied with the TV.
Attach the two parts of the stand unit to each
other using the 4 screws and the hex key
(supplied with the product) as shown.
other using the 4 screws and the hex key
(supplied with the product) as shown.
1
2
1 Insert the stand into the openings on the
bottom of the TV.
2 Insert and tighten the 4 long screws into the
4 holes on the rear of the TV.
3
Supplied accessories
Remote control
unit (
g1)
AC cord (
g1)
Pages 6 and 7
Product shape
varies in some
countries.
Page 4
• “AAA” size battery (
g2)..........Page 6
Cable clamp
(Small
g1, Large g1)
Page 4
Cable tie (
g1)
Page 4
3 RCA to 15-pin
D-sub adapter
(
g1)
Page 10
• Operation manual (This publication)
Quick guide
Stand unit (
g1)
Page 3
Attaching the stand
Before attaching (or detaching) stand, unplug the AC cord from the AC INPUT terminal.
CAUTION
• Attach the stand in the correct direction.
• Be sure to follow the instructions. Incorrect installation of the stand may result in the TV falling over.
• Attach the stand in the correct direction.
• Be sure to follow the instructions. Incorrect installation of the stand may result in the TV falling over.
NOTE
• To detach the stand, perform the above steps in reverse
• To detach the stand, perform the above steps in reverse
order.
Before performing work spread cushioning over the base area to lay the TV on, making sure the area is
completely fl at. This will prevent it from being damaged.
completely fl at. This will prevent it from being damaged.
Hex key
Short screw
Hex key
Long screw
Soft cushion
LC-42XD1E_gb_a.indd 3
LC-42XD1E_gb_a.indd 3
2006/10/27 10:21:21
2006/10/27 10:21:21
4
Bundle the AC cord with the clamp (small).
Quick guide
Setting the TV
Standard DIN45325
plug (IEC 169-2)
75
plug (IEC 169-2)
75
q coaxial cable
Antenna
Connect the antenna cable from your antenna-/cable socket or the (room-/roof) antenna for antenna input terminal on the
back of your TV set to receive digitally/terrestrially broadcast stations.
An indoor antenna can also be used under good reception conditions. Passive and active room antennas are offered
commercially. In an active antenna its power is supplied via the antenna input terminal.
The supply voltage (5V) must be correspondingly set under “Supply voltage”. (Page 16)
back of your TV set to receive digitally/terrestrially broadcast stations.
An indoor antenna can also be used under good reception conditions. Passive and active room antennas are offered
commercially. In an active antenna its power is supplied via the antenna input terminal.
The supply voltage (5V) must be correspondingly set under “Supply voltage”. (Page 16)
* Ferrite Core
The Ferrite Core should be permanently attached and never removed from the AC cord.
Setting the TV on the wall
• This TV should be mounted on the wall only with the wall mount bracket available from SHARP. (See page 36.)
The use of other wall mount brackets may result in an unstable installation and may cause serious injuries.
•
Installing the LCD Colour TV requires special skill that should only be performed by qualifi ed service personnel.
Customers should not attempt to do the work themselves. SHARP bears no responsibility for improper mounting
or mounting that results in accident or injury.
or mounting that results in accident or injury.
• You can ask a qualifi ed service personnel about using an optional bracket to mount the TV to the wall.
AC cord
Product shape
varies in some
countries.
Cable clamp (small)
Cable tie
Place the TV close to the AC outlet, and
keep the power plug within reach.
keep the power plug within reach.
Ferrite Core *
Cable
clamp
(large)
Bundle the
cables with
the clamp.
LC-42XD1E_gb_a.indd 4
LC-42XD1E_gb_a.indd 4
2006/10/27 10:21:25
2006/10/27 10:21:25
5
TV (Front view)
Quick guide
TV (Rear view)
NOTE
• Only if you use an
• Only if you use an
active terrestrial
antenna, select
“yes (5V)” under
“Supply voltage”.
(Page 16)
antenna, select
“yes (5V)” under
“Supply voltage”.
(Page 16)
AC INPUT terminal
OPC sensor
Remote control sensor
B (Standby/On) indicator
OPC indicator
a (Power button)
MENU
button
i (
l/k)
(Volume buttons)
P
(
s/r)
(Programme [channel] buttons)
SLEEP indicator
EXT 2 (AV) terminal
EXT 3 terminals
Headphone jack
EXT 1 (RGB) terminal
EXT 5 (HDMI/AUDIO)
terminals
terminals
Antenna input
terminal
(DVB-T 5V=/80 mA)
terminal
(DVB-T 5V=/80 mA)
OUTPUT (Audio)
terminals
terminals
EXT 4 terminals
RS-232C terminal
COMMON
INTERFACE slot
INTERFACE slot
EXT 6 (HDMI) terminal
Rear
panel:
LC-
42XD1E
panel:
LC-
42XD1E
Rear
panel:
LC-
37XD1E
panel:
LC-
37XD1E
LC-42XD1E_gb_a.indd 5
LC-42XD1E_gb_a.indd 5
2006/10/27 10:21:26
2006/10/27 10:21:26
6
Quick guide
CAUTION
Improper use of batteries can result in chemical leakage or explosion. Be sure to follow the instructions below.
• Do not mix batteries of different types. Different types of batteries have different characteristics.
• Do not mix old and new batteries. Mixing old and new batteries can shorten the life of new batteries or cause
• Do not mix batteries of different types. Different types of batteries have different characteristics.
• Do not mix old and new batteries. Mixing old and new batteries can shorten the life of new batteries or cause
chemical leakage in old batteries.
• Remove batteries as soon as they have worn out. Chemicals that leak from batteries can cause a rash. If you fi nd
any chemical leakage, wipe thoroughly with a cloth.
• The batteries supplied with this product may have a shorter life expectancy due to storage conditions.
• If you will not be using the remote control unit for an extended period of time, remove the batteries from it.
• If you will not be using the remote control unit for an extended period of time, remove the batteries from it.
30°
30°
Remote control sensor
5 m
Press and slide the battery cover to open it.
Insert two supplied “AAA” size batteries.
• Place batteries with their terminals corresponding
to the (
e) and (f) indications in the battery
compartment.
Close the battery cover.
1
2
2
3
Inserting the batteries
Before using the TV for the fi rst time, insert two “AAA” size batteries (supplied). When the batteries become
depleted and the remote control unit fails to operate, replace the batteries with new “AAA” size batteries.
depleted and the remote control unit fails to operate, replace the batteries with new “AAA” size batteries.
Using the remote control unit
Use the remote control unit by pointing it towards the remote control sensor. Objects between the remote control
unit and sensor may prevent proper operation.
unit and sensor may prevent proper operation.
Cautions regarding the remote control unit
• Do not expose the remote control unit to shock.
In addition, do not expose the remote control unit to liquids, and do not
In addition, do not expose the remote control unit to liquids, and do not
place in an area with high humidity.
• Do not install or place the remote control unit under direct sunlight. The
heat may cause deformation of the unit.
• The remote control unit may not work properly if the remote control sensor
of the TV is under direct sunlight or strong lighting. In such case, change
the angle of the lighting or TV, or operate the remote control unit closer to
the remote control sensor.
the angle of the lighting or TV, or operate the remote control unit closer to
the remote control sensor.
LC-42XD1E_gb_a.indd 6
LC-42XD1E_gb_a.indd 6
2006/10/27 10:21:28
2006/10/27 10:21:28
Click on the first or last page to see other LC-42XD1E (serv.man12) service manuals if exist.