Sharp LC-37D44EBK (serv.man11) User Manual / Operation Manual ▷ View online
Quick guide
TV (Front view)
TV (Rear view)
10
1
2
6
7
8
9
3
4
5
13
11
12
NOTE
• Only if you use an active terrestrial antenna, select “On (5V)” under “Supply Voltage”. (See page 18.)
• Only if you use an active terrestrial antenna, select “On (5V)” under “Supply Voltage”. (See page 18.)
WARNING:
Make sure that the volume is turned
down before using or connecting
earphones and headphones.
Listen to audio at moderate levels.
Excessive sound pressure from
earphones and headphones can
cause hearing loss.
Make sure that the volume is turned
down before using or connecting
earphones and headphones.
Listen to audio at moderate levels.
Excessive sound pressure from
earphones and headphones can
cause hearing loss.
7
Remote control sensor
a (Power button)
b (Input Source) button
i (
l/k) (Volume buttons)
P (
s/r)
(Programme [channel] buttons)
MENU button
1 RS-232C
terminal
2
EXT 4 (ANALOGUE RGB/AUDIO)
terminals
terminals
3
EXT 5 (COMPONENT) terminals
4
EXT 1 (RGB) terminal
5
EXT 2 (RGB) terminal
6
Antenna input terminal
(DVB-T 5V=/80 mA)
7
OUTPUT (AUDIO) terminals
8
EXT 6 (HDMI/AUDIO) terminals
9
EXT 7 (HDMI) terminal
10 COMMON INTERFACE slot
11 EXT 3 terminals
12 Headphone jack
13 AC INPUT terminal
11 EXT 3 terminals
12 Headphone jack
13 AC INPUT terminal
B (Standby/On) indicator
LC-37D44E-gb.indd 7
LC-37D44E-gb.indd 7
2008/06/17 10:26:25
2008/06/17 10:26:25
Quick guide
Turning on the power
Press
a on the TV or B on the remote control unit.
Standby mode
Press
B on the remote control unit when the TV is
on.
• The TV enters standby mode and the image on the screen
disappears.
• The
B indicator on the TV changes from green to red.
• To completely turn off the power to the TV, unplug the AC
cord from the AC outlet. However, do not unplug the AC
cord unless otherwise instructed.
cord unless otherwise instructed.
Display status indicator
Off
Power off.
Red
The TV is in standby mode.
Green
The TV is on.
NOTE
• If you are not going to use this TV for a long period of time,
• If you are not going to use this TV for a long period of time,
be sure to remove the AC cord from the power outlet.
• Weak electric power is still consumed even when
a is
turned off.
• In DTV input mode, if the power is turned off immediately
after a setting change from the menu screen, the new
setting or channel information may not be memorised.
setting or channel information may not be memorised.
Initial auto installation (Analogue)
When the TV is powered on for the first time after
purchase, the initial auto installation (Analogue) is
invoked. You can automatically set language, country
and channels in successive operations.
purchase, the initial auto installation (Analogue) is
invoked. You can automatically set language, country
and channels in successive operations.
NOTE
• The initial auto installation functions only once. If the initial
• The initial auto installation functions only once. If the initial
auto installation is not completed (ex: When menu screen
disappeared by not operating for a few minutes, when the
power shut down, etc.), try Auto Installation from the Setup
menu. (See page 15.)
disappeared by not operating for a few minutes, when the
power shut down, etc.), try Auto Installation from the Setup
menu. (See page 15.)
• The initial auto installation stops by pressing RETURN.
Setting the on-screen display language
1 Press a/b/c/d to select the desired language
listed on the screen.
2 Press OK to enter the setting.
Setting the country or area
1 Press a/b/c/d to select your country or area
listed on the screen.
2 Press OK to enter the setting.
• The programme auto search starts at the same time.
• The programme auto search starts at the same time.
After this setting, auto search starts with the following
order:
order:
1 Programme auto search
2 Auto labelling
3 Auto sorting
4 Preset download
You do not need to do anything during the auto search.
The setup menu disappears and you can watch the
programme on channel 1.
programme on channel 1.
1
2
Using the analogue programme list
You can also select the desired channel from
programme list instead of using 0 - 9 numeric buttons
or P (
programme list instead of using 0 - 9 numeric buttons
or P (
r/s).
Press OK when no other menu screen is
displayed. (Except when an external input
source is selected.)
displayed. (Except when an external input
source is selected.)
Press
a/b to select the desired channel to
tune in, and then press OK.
Press END to exit the Programme List.
Initial auto installation (DTV)
Digital Video Broadcasting is a transmission scheme.
It is much more than a simple replacement for existing
analogue television transmission. DVB provides more
stations, clearer picture quality and other services
displayed on the screen. It also allows a range of new
features and services including subtitles and multiple
audio tracks.
It is much more than a simple replacement for existing
analogue television transmission. DVB provides more
stations, clearer picture quality and other services
displayed on the screen. It also allows a range of new
features and services including subtitles and multiple
audio tracks.
To watch DTV broadcasts, follow the procedures below
to scan all available services in your area.
to scan all available services in your area.
Press DTV or
b to access the DTV mode.
Press DTV MENU and the DTV Menu screen
displays.
displays.
Press
c/d to select “Installation”.
Press
a/b to select “Auto Installation”, and
then press OK.
If you have already set the PIN, enter it here. If
not, enter the factory preset PIN “1234”.
not, enter the factory preset PIN “1234”.
• See page 17 for setting PIN.
• A confirmation message displays. Press
• A confirmation message displays. Press
c/d to
select “Yes”, and then press OK to start the search.
The TV starts scanning all available DTV and
radio services in your area.
radio services in your area.
NOTE
• The language and country settings used in this operation
• The language and country settings used in this operation
are the settings you have already set while executing
the Initial auto installation (Analogue). If you want to
reconfigure the country setting, for instance after moving to
another country, conduct “Auto Installation” from the Setup
menu again.
the Initial auto installation (Analogue). If you want to
reconfigure the country setting, for instance after moving to
another country, conduct “Auto Installation” from the Setup
menu again.
• The services are stored according to the channel number
information embedded in the stream (if available). If
the information is not available, the services are stored
according to the order in which they were received.
the information is not available, the services are stored
according to the order in which they were received.
If you would like to sort the order, it is possible to arrange it
as explained in page 24.
• To cancel the scan in progress, press END.
• You cannot select any DTV-related menu items unless
• You cannot select any DTV-related menu items unless
“Auto Installation” has been completed.
1
2
3
1
2
2
3
4
4
5
8
LC-37D44E-gb.indd 8
LC-37D44E-gb.indd 8
2008/06/16 13:38:16
2008/06/16 13:38:16
Using external equipment
Setting the input source
To view external source images, select the input source using
b on the remote control unit or the TV.
NOTE
• The cables marked with * are commercially available items.
• The cables marked with * are commercially available items.
Connecting a VCR
You can use the EXT 1 or 2 terminals when connecting
a VCR and other audiovisual equipment.
If your VCR supports TV-VCR advanced AV Link
systems, you can connect the VCR to the EXT 2
terminal of the TV using the fully-wired SCART cable.
a VCR and other audiovisual equipment.
If your VCR supports TV-VCR advanced AV Link
systems, you can connect the VCR to the EXT 2
terminal of the TV using the fully-wired SCART cable.
AV OUTPUT
NOTE
• TV-VCR advanced AV Link systems may not be compatible
• TV-VCR advanced AV Link systems may not be compatible
with some external sources.
• TV-OUT from EXT 1 is not outputted when EXT 6 (HDMI),
EXT 7 (HDMI) or DTV is selected as the input.
Connecting a game console or
camcorder
camcorder
A game console, camcorder and some other
audiovisual equipment are conveniently connected
using the EXT 3 terminals.
audiovisual equipment are conveniently connected
using the EXT 3 terminals.
NOTE
• EXT 3: The S-VIDEO terminal has priority over the VIDEO
• EXT 3: The S-VIDEO terminal has priority over the VIDEO
terminals.
Connecting a DVD player
You can use the EXT 2, 3, 5, 6 (HDMI) or 7 (HDMI)
terminals when connecting to a DVD player and other
audiovisual equipment.
terminals when connecting to a DVD player and other
audiovisual equipment.
AV OUTPUT
NOTE
• EXT 3: The S-VIDEO terminal has priority over the VIDEO
• EXT 3: The S-VIDEO terminal has priority over the VIDEO
terminals.
NOTE
• When connecting an HDMI-DVI conversion adapter/cable
• When connecting an HDMI-DVI conversion adapter/cable
to the HDMI terminal, the image may not come in clearly.
YP
B
P
R
L-A
UDIO-R
COMPONENT
9
VCR
Decoder
SCART cable*
SCART cable*
EXT 1 or 2
Game
console
Camcorder
S-video cable*
Composite
video cable*
AUDIO cable*
EXT 3
or
DVD player
EXT 3
or
AUDIO cable*
S-video cable*
Composite
video cable*
EXT 5
AUDIO cable*
Component cable*
DVD player
DVD player
HDMI-DVI conversion adapter/
cable*
When using an HDMI-DVI
conversion adapter/cable,
input the Audio signal here.
If not, use EXT 7.
conversion adapter/cable,
input the Audio signal here.
If not, use EXT 7.
EXT 6
DVD player
HDMI-certified cable*
EXT 7
LC-37D44E-gb.indd 9
LC-37D44E-gb.indd 9
2008/06/16 13:38:16
2008/06/16 13:38:16
Using external equipment
Connecting a decoder
You can use the EXT 1 terminal when connecting a
decoder and other audiovisual equipment.
decoder and other audiovisual equipment.
NOTE
• In cases when the decoder needs to receive signal from
• In cases when the decoder needs to receive signal from
the TV, make sure to set “Decoder” to “EXT1” in the
Programme Setup “Manual Adjust” menu. (See page 16.)
Programme Setup “Manual Adjust” menu. (See page 16.)
• Do not connect the decoder to the EXT 2 terminal.
Connecting a PC
Use the EXT 4 terminals to connect a PC.
NOTE
• The cables marked with * are commercially available items.
• The PC input terminals are DDC1/2B-compatible.
• Refer to page 33 for a list of PC signals compatible with the
• The cables marked with * are commercially available items.
• The PC input terminals are DDC1/2B-compatible.
• Refer to page 33 for a list of PC signals compatible with the
TV.
• When connecting to a PC, the correct input signal type is
automatically detected.
Using AV Link function
This TV incorporates three typical AV Link functions
for smooth connections between the TV and other
audiovisual equipment.
for smooth connections between the TV and other
audiovisual equipment.
One Touch Play
While the TV is in standby mode, it automatically turns
on and plays back the image from the audiovisual
source (e.g. VCR, DVD).
on and plays back the image from the audiovisual
source (e.g. VCR, DVD).
WYSIWYR (What You See Is What You Record)
When the remote control unit of the connected VCR
has the WYSIWYR button, you can automatically start
recording by pressing the WYSIWYR button.
has the WYSIWYR button, you can automatically start
recording by pressing the WYSIWYR button.
Preset Download
Automatically transfers the channel preset information
from the tuner on the TV to the one on the connected
audiovisual equipment (e.g. VCR) via the EXT 2
terminal.
from the tuner on the TV to the one on the connected
audiovisual equipment (e.g. VCR) via the EXT 2
terminal.
NOTE
• Refer to operation manuals of each external equipment for
• Refer to operation manuals of each external equipment for
the details.
• Only works when the audiovisual equipment is connected
to the EXT 2 terminal on the TV with AV Link via a fully
wired SCART.
wired SCART.
• The use of the AV Link function is only possible if the
TV-set has enforced a complete auto-installation with the
connected audiovisual equipment (page 8, Initial auto
installation).
connected audiovisual equipment (page 8, Initial auto
installation).
The availability of the AV Link function depends on
the audiovisual equipment used. Depending on the
manufacturer and type of equipment used, it is possible
that the described functions may be completely or partially
unusable.
manufacturer and type of equipment used, it is possible
that the described functions may be completely or partially
unusable.
10
Decoder
EXT 1
SCART cable*
PC
ø 3.5 mm stereo minijack cable*
RGB cable*
PC
RGB/DVI conversion cable*
ø 3.5 mm stereo minijack cable*
EXT 4
EXT 4
LC-37D44E-gb.indd 10
LC-37D44E-gb.indd 10
2008/06/16 13:38:20
2008/06/16 13:38:20
Click on the first or last page to see other LC-37D44EBK (serv.man11) service manuals if exist.