DOWNLOAD Sharp LC-37AD1E (serv.man34) Service Manual ↓ Size: 5.04 MB | Pages: 101 in PDF or view online for FREE

• Installing the LCD Colour TV requires special skill that should only be performed by qualified service personnel.

Using an optional bracket to mount the Display
• You can ask a qualified service personnel about using an optional AN-37AG1 bracket to mount the Display

to the wall.

• Carefully read the instructions that come with the bracket before beginning work.

AN-37AG1 wall mount bracket. (See the bracket instructions for details.)

How to install the AVC System vertically using the stand unit.
• Use the supplied stand unit for installing the AVC System vertically in an upright position.

Peel each spacer
away from the
paper and attach
to the four bulging
areas on the stand.

Peel each cushion
away from the
paper and attach
to the four areas at
the bottom.

Insert the stand into the AVC
System, making sure that the
thick and thin bulges of the
stand align with the big and
small holes on the AVC
System.

Stand
spacer

Bulge

Stand cushion

Thin bulge

Thick
bulge

Big hole

Small
hole

Stand screw

• When mounting the AVC System vertically, always use the supplied stand. Be careful not to block vent holes when

standing up directly on the floor or a flat surface as this can result in equipment failure.

Bulge

Attaching point

Attaching point

Vertical mounting

Angular mounting

5

°

• You can set the Display on the

wall up to 5 degrees forward
when the speaker is attached and
up to 20 degrees forward when
the speaker is not attached. Do
not set the angle outside those
ranges.

LC-37AD1E(E)-a

03.11.28, 8:15 AM

11

+

+

_

_

Open the battery cover.

Insert two supplied “AA” size
batteries.

• Place batteries with their terminals

corresponding to the (e) and (f)
indications in the battery compartment.

Close the battery cover.

Improper use of batteries can result in chemical leakage or explosion. Be sure to follow the instructions below.
• Place the batteries with their terminals corresponding to the (e) and (f) indications.
• Do not mix batteries of different types. Different types of batteries have different characteristics.
• Do not mix old and new batteries. Mixing old and new batteries can shorten the life of new batteries or cause

chemical leakage in old batteries.

• Remove batteries as soon as they have worn out. Chemicals that leak from batteries can cause a rash. If you

find any chemical leakage, wipe thoroughly with a cloth.

• The batteries supplied with this product may have a shorter life expectancy due to storage conditions.
• If you will not be using the remote control unit for an extended period of time, remove the batteries from it.

Before using the System for the first time, insert two “AA” size batteries (supplied).  When the batteries become
depleted and the remote control fails to operate, replace the batteries with new “AA” size batteries.

Use the remote control unit by pointing it towards the remote sensor window.
Objects between the remote control unit and sensor window may prevent proper
operation.

• Do not expose the remote control unit to shock.

In addition, do not expose the remote control unit to liquids, and do not place
in an area with high humidity.

• Do not install or place the remote control unit under direct sunlight.

The heat may cause deformation of the unit.

• The remote control unit may not work properly if the remote sensor window of

the Display is under direct sunlight or strong lighting. In such case, change
the angle of the lighting or Display, or operate the remote control unit closer to
the remote sensor window.

LC-37AD1E(E)-a

03.11.28, 8:15 AM

12

Standard DIN45325 plug (IEC169-2)

75-ohm coaxial cable (round cable)
(commercially available)

Simple operations for watching a TV programme

To enjoy a clearer picture, use an outdoor antenna. The following is a brief explanation of the types of connections
that are used for coaxial cable.

If your outdoor antenna uses a 75-ohm coaxial cable with a standard DIN45325
plug (IEC 169-2), plug it into the DIGITAL IN terminal at the rear of the AVC
System.

• Always turn off the main power of Display and AVC System when connecting the AC cords.
• Disconnect the AC cords from the AC outlet, Display and AVC System if the System will not be used for a long period of

time.

Product shape varies

in some countries.

Product shape varies

in some countries.

Antenna cable

(supplied)

For viewing only digital broadcasts,
you do not need to connect the
antenna cable.

(ex. For viewing both analogue and digital broadcasts)

(ex. For viewing analogue broadcasts)

LC-37AD1E(E)-a

03.11.28, 8:16 AM

13

When the System powers on for the first time after
purchase, the initial auto installation is invoked. You
can automatically set language, country and channels
in successive operations.

• The initial auto installation functions only once. If the initial

auto installation is not completed, (ex: When menu screen
disappeared by not operating for a few minutes, when
the power shut down, etc.), try Auto Installation from the
set up menu. (See page 27.)

• The initial auto installation stops by pressing RETURN.

1 Press  a/b/c/d to select your country

or area listed on the screen.

2 Press OK to enter the setting.

• The programme auto search starts at the same

time.

1 Press  a/b/c/d to select the desired

language listed on the screen.

2 Press OK to enter the setting.

After this setting, auto search starts with the following
order.

1 Programme auto search
2 Auto labelling
3 Auto sorting
4 Preset download

You do not need to do anything during the auto search.
(Go to the next page.)

• The illustrations and on-screen displays in this manual

are for explanation purposes and may vary slightly from
the actual operations.

English

Deutsch

Français

Austria

Belgium

Denmark

Finland

LC-37AD1E(E)-a

03.11.28, 8:16 AM

14