DOWNLOAD Sharp LC-32WD1E (serv.man2) Service Manual ↓ Size: 10.52 MB | Pages: 38 in PDF or view online for FREE

3

To receive analogue or digital terrestrially broadcasted stations, connect the antenna cable (from the antenna/cable 
socket or the room/roof antenna) to the input antenna port on the back of the television. If there is good reception, an 
indoor antenna can also be used. If you are using an active antenna, the supply voltage (5V) must also be set. (See 
page 18.)

Connect the AC cord to the power port on the back of the television.

Plug the AC cord into the AC outlet. 

IT IS THE RESPONSIBILITY OF THE INSTALLER TO MAKE SURE THE TELEVISION IS INSTALLED 
SAFELY. IF YOU ARE USING ANY ACCESSORIES WITH THIS TELEVISION (SUCH AS A WALL 
MOUNT BRACKET OR A TELEVISION STAND), FOLLOW THE ACCESSORY MANUFACTURER’S 
SPECIFICATIONS AND INSTALLATION INSTRUCTIONS. 

A A

Remote control unit (x1)

Batteries (x2)

Cable clamp (x1)

(For Europe, except 

U.K. and Eire)

Cable tie (x1)

AC cord (x1 or x2)

(For U.K. and Eire)

U.K. type 3-pin AC cord is only  

included with model LC-32WD1E

Page 3

•

Operation manual (This publication)

1

2

3

(For Europe, except
U.K. and Eire)

(For U.K. and Eire)

AC cord

Place the TV close to 
the AC outlet, and keep 
the power plug within 
reach.

Page 3 of 204  June 8, 2007

TINS-DO52WJN1

SHPRN000205B-GLDN

4

•

This TV should be mounted on the wall only with a wall mount bracket approved and available from SHARP. (See 
page 30.) The use of other wall mount brackets may result in an unstable installation and may cause serious 
injuries. 

•

You can ask a qualified service personnel about using an optional bracket to mount the TV to the wall. 

•

Installing the TV on the wall requires special skill that should only be performed by qualified service personnel. 
Customers should not attempt to do the work themselves. SHARP bears no responsibility for improper mounting 
or mounting that results in accident or injury. 

Before using the remote control, install the two (supplied) AA batteries. When the batteries become worn out or “dead”, 
replace the batteries.

Hold in the tab on the battery cover and pull the cover towards the direction of the arrow. 

Insert two AA batteries. 

Place the batteries with the terminals on the batteries (+ and -) in the positions as 
indicated in the battery compartment.

Insert the smaller tab of the battery cover into the remote control opening (1) and then 
press down on the cover until it clicks into place (2). 

CAUTION:
Improper use of batteries can result in chemical leakage or explosion. Be sure to follow the 
instructions below.

•

Do not mix different types of batteries. Different types of batteries have different 
characteristics.

•

Do not mix old and new batteries. Mixing old and new batteries can shorten the life of new batteries or cause 
chemical leakage in old batteries. 

•

Remove batteries as soon as they have worn out. Chemicals that leak from batteries can cause a rash. If you find 
any chemical leakage, wipe the area clean with a cloth. 

•

The batteries supplied with this product may have a shorter life expectancy due to storage conditions.

•

If you will not be using the remote control for an extended period of time, remove the batteries from it.

•

Dispose batteries according to local requirements. Please do not use the ordinary dust bin. 

1

2

Page 4 of 204  June 8, 2007

TINS-DO52WJN1

SHPRN000205B-GLDN

5

To use the remote control, point it towards the remote control sensor on the front of the TV. 

•

Do not expose the remote control to shock. 

•

Do not expose the remote control to high humidity conditions or liquids. 

•

Do not expose the remote control to direct sunlight. The heat may cause deformations 
of the remote control. 

•

If there are objects between the remote control and the sensor, it may prevent normal 
operation. 

•

If the remote control sensor on the TV is in direct sunlight or strong lighting, the remote 
control may not work as expected. If you experience this, change the lighting, angle to 
the television, or use the remote control closer to the TV. 

For information on the LED indicator meanings, see page 7.

30

30

5 m

OPC LED indicator

SLEEP LED indicator

Standby/On LED indicator
Remote Control indicator

Remote control sensor

OPC sensor

Page 5 of 204  June 8, 2007

TINS-DO52WJN1

SHPRN000205B-GLDN

6

DTV mode— Press  

to 

change 

languages.
Analogue TV mode—Each time you 
press 

, the mode switches as 

illustrated in the following table.

Switches the TV between on and 
standby mode. (See page 7.)

AV  MODE
Selects a preset audio/video setting 
(AV Mode). (See page 13.)

OPC
Turns the Optical Picture Control 
(OPC) “On” and “Off”. (See page 13.)

0–9
TV/DTV: Directly selects the channel.
Teletext: Selects the page.

Returns to the previous channel or AV 
input. 

Selects wide mode. (See page 20.)

See “Using Multiplex” on page 6.

EPG
DTV: Displays the EPG (Electronic 
Programme Guide) screen. (See 
page 26.)

ESG
DTV: Displays the ESG (Electronic 
Service Guide) screen. (See page 26.)

TV: Selects the teletext mode. (See 
page 21.)
DTV: Selects the teletext mode or 
MHEG5 (if available). If both are 
available, press for MHEG5. Press for 
1-2 seconds for teletext. (See page 21 
and 28.)

S/T/W/X (Cursor)
Selects an item on the screen. 

Press to exit the on-screen display 
menu screen. 

Reveals/hides hidden teletext 
information. (See page 20.)

TV/DTV/External: Freezes the on-
screen image.
Teletext: Stop updating teletext pages 
automatically or release the hold 
mode.(See page 20.)

Turns SRS TruSurround® “On” and 
“Off”. (See page 15.)

DTV: Switches between RADIO and 
DTV Mode. 

 (Mute)

Turns the sound “On” and “Off”. 

Switches between analogue TV mode 
and DTV mode.

 (+ / -) (Volume)

Increases or decreases the volume.

20 P  (

)

TV/DTV: Selects the channel.
External: Switches to TV or DTV input 
mode. 
Teletext: Move to the next or previous 
page.

 (Input source)

Selects an input source. (See page 9.)

Sets the amount of time the TV will 
stay on before automatically turning 
off. (In units of 30 minutes to a 
maximum of 2 hours 30 minutes.)

 (Display information)

TV: Displays channel information. (See 
page 21.)
DTV: Displays the service banner. 
(See page 27.)

DTV: Displays the DTV on-screen 
display menus. (See page 22.)

Displays the Main TV on-screen 
display menus. (See page 11.)

Selects an option in the on-screen 
display menu. Displays the programme 
list (except for external input).

Returns to the previous menu. 

 (Subpage)

Displays current time.
Teletext: Displays or hides subpages.
(See page 20.)

TV/External: Turns the teletext 
subtitles “On” and “Off”.
DTV: Displays/hides the subtitle 
selection.

TeleText: Selects a group or block of 
pages displayed in the coloured 
brackets at the bottom of the screen by 
pressing the corresponding colour 
button on the remote control.
DTV: When using the on-screen 
display, assigned tasks as indicated at 
the bottom of the screen.

Mono
Mono

Mono

A2 TV broadcasts selection
Mono

Mono

Stereo

Stereo, Mono

Dual

Channel A (I), Channel B (II), 
Channel AB (I+II)

NICAM TV broadcasts selection
Mono

NICAM Mono

Stereo

NICAM Stereo, FM/AM* Mono

Dual

NICAM Channel A (I), NICAM 
Channel B (II), NICAM Channel 
AB (I+II), FM/AM Mono*

* Depending on the country, the option is 
either AM or FM mono. 

Page 6 of 204  June 8, 2007

TINS-DO52WJN1

SHPRN000205B-GLDN