Sharp LC-32LD145E Service Manual ▷ View online
9
LC-32LD145
LC-39LD145
Operation Manual (Continued)
English - 8 -
Viewing the TV
TV Control button & Operation
1. Up direction
2. Down direction
3. Programme/Volume / AV / Standby-On selection
2. Down direction
3. Programme/Volume / AV / Standby-On selection
switch
The Control button allows you to control the Volume/
Programme/ Source and Standby-On functions of
the TV.
To change volume: Increase the volume by pushing
To change volume: Increase the volume by pushing
the button up. Decrease the volume by pushing the
button down.
To change channel: Press the middle of the button,
To change channel: Press the middle of the button,
the channel information banner will appear on screen.
Scroll through the stored channels by pushing the
button up or down
To change source: Press the middle of the button
To change source: Press the middle of the button
twice, the source list will appear on screen. Scroll
through the available sources by pushing the button
up or down.
To turn the TV off: Press the middle of the button
To turn the TV off: Press the middle of the button
down and hold it down for a few seconds, the TV will
turn into standby mode.
Inserting the Batteries into the Remote
Insert batteries in the remote before operating your TV.
Lift the cover on the back of the remote upward gently.
Lift the cover on the back of the remote upward gently.
Install two
AAA batteries. Make sure to match the +
and - ends of the batteries in the battery compartment
(observe the correct polarity) Replace the cover.
Connect Power
IMPORTANT: The TV set is designed to operate on
220-240V AC, 50 Hz socket. After unpacking, allow
the TV set to reach the ambient room temperature
before you connect the set to the mains. Plug the
power cable to the mains socket outlet.
Antenna/Cable Connection
Connect the “aerial” or “cable TV” plug to the AERIAL
INPUT (ANT) socket located on the back of the TV.
Notification
Manufactured under license from Dolby Laboratories.
TRADEMARK ACKNOWLEDGMENT
“Dolby” and the double-D symbol are
TRADEMARK ACKNOWLEDGMENT
“Dolby” and the double-D symbol are
trademarks of Dolby Laboratories.
“HDMI, the HDMI logo and High-Definition Multimedia
Interface are trademarks or
registered trademarks of HDMI
Licensing LLC.”
10
LC-39LD145
LC-32LD145
Operation Manual (Continued)
English - 11 -
Connector
Type
Cables
Device
Scart
Connection
(back)
VGA
Connection
(back)
SIDE AV
PC/YPbPr
Audio
Connection
(side)
Side Audio
YPbPr or PC Connection Cable
(Not supplied)
HDMI
Connection
(back)
SPDIF
Connection
(back)
SIDE AV
Side AV
(Audio/Video)
Connection
(side)
HEADPHONE
Headphone
Connection
Connection
(side)
YPbPr Video
Connection
(back)
PC to YPbPr Connection Cable
USB
Connection
(side)
CI
Connection
(side)
CAM
module
Connections
NOTE: When connecting a device via the YPbPr or Side AV input, you must use a connection cable to
enable connection. See the illustrations above. | You can use YPbPr to VGA cable (not supplied) to enable YPbPr
signal via VGA input.
|You cannot use VGA and YPbPr at the same time. | To enable PC audio, you will need to
use the SIDE AV CONNECTION cable’s WHITE & RED inputs.
| If an external device is connected via the SCART
socket, the TV will automatically switch to AV mode.
| When receiving DTV channels (Mpeg4 H.264) or while in
Media Browser mode, output will not be available via the scart socket.
| When using the wall mounting kit (available
from third party in the market), we recommend that you plug all your cables into the back of the TV before mounting
on the wall.
| Insert or remove the CI module only when the TV is SWITCHED OFF. You should refer to the module
instruction manual for details of the settings.
11
LC-32LD145
LC-39LD145
DIMENSIONS
English - 20 -
Dimensional Drawings
Note: The unit of the measurements is mm.
LC32LD145
12
LC-39LD145
LC-32LD145
English - 21 -
Dimensional Drawings LC39LD145
Click on the first or last page to see other LC-32LD145E service manuals if exist.