Sharp LC-32LD135K (serv.man2) Service Manual ▷ View online
21
LC-32LD135
5
- No alignment, tuning or calibration required
- Digital low-IF architecture
- Integrated channel select filters
- Flexible output interface
- ALIF to analog TV demodulator or SoC
- DLIF to digital TV demodulator or SoC
- 3.3 and 1.8 V power supplies
- Standard CMOS process technology
- 5 x 5 mm, 32-pin QFN package
- RoHS compliant
- Digital low-IF architecture
- Integrated channel select filters
- Flexible output interface
- ALIF to analog TV demodulator or SoC
- DLIF to digital TV demodulator or SoC
- 3.3 and 1.8 V power supplies
- Standard CMOS process technology
- 5 x 5 mm, 32-pin QFN package
- RoHS compliant
Figure 1: Pin description
22
LC-32LD135
7
B. M88TS2022 Satellite Tuner
B.1. Features and General Description
B.2. Pin Assigment
23
LC-32LD135
8
B.3. Absolute Maximum Ratings and Recommended Operating
Conditions
3. AUDIO AMPLIFIER STAGES
A. MAIN AMPLIFIER (TAS5719)(6-8 W option)
a. General Description
The TAS5717/TAS5719 is a 10-W/15-W, efficient,digital audio-power amplifier for
driving stereo bridge-tied speakers. One serial data input allows processing of up to two
discrete audio channels and seamless integration to most digital audio processors and MPEG
decoders. The device accepts a wide of input data and data rates. A fully programmable data
path routes these channels to the internal speaker drivers.
discrete audio channels and seamless integration to most digital audio processors and MPEG
decoders. The device accepts a wide of input data and data rates. A fully programmable data
path routes these channels to the internal speaker drivers.
The TAS5717/9 is a slave-only device receiving all clocks from external sources. The
TAS5717/TAS5719 operates with a PWM carrier between a 384-kHz switching rate and a
352-KHz switching rate, depending on the input sample rate. Oversampling combined with a
fourth-order noise shaper provides a flat noise floor and excellent dynamic range from 20 Hz
to 20 kHz.
352-KHz switching rate, depending on the input sample rate. Oversampling combined with a
fourth-order noise shaper provides a flat noise floor and excellent dynamic range from 20 Hz
to 20 kHz.
24
LC-32LD135
9
b. Features
• Audio Input/Output
– TAS5717 Supports 2×10 W and TAS5719 Supports 2×15 W Output
– Wide PVDD Range, From 4.5 V to 26 V
– Efficient Class-D Operation Eliminates Need for Heatsinks
– Requires Only 3.3 V and PVDD
– One Serial Audio Input (Two Audio Channels)
– I2C Address Selection via PIN (Chip Select)
– Supports 8-kHz to 48-kHz Sample Rate (LJ/RJ/I2S)
– External Headphone-Amplifier Shutdown Signal
– Integrated CAP-Free Headphone Amplifier
– Stereo Headphone (Stereo 2-V RMS Line Driver) Outputs
• Audio/PWM Processing
– Independent Channel Volume Controls With 24-dB to Mute
– Programmable Two-Band Dynamic Range Control
– 14 Programmable Biquads for Speaker EQ
– Programmable Coefficients for DRC Filters
– DC Blocking Filters
– 0.125-dB Fine Volume Support
• General Features
– Serial Control Interface Operational Without MCLK
– Factory-Trimmed Internal Oscillator for Automatic Rate Detection
– Surface Mount, 48-Pin, 7-mm × 7-mm HTQFP Package
– AD, BD, and Ternary PWM-Mode Support
– Thermal and Short-Circuit Protection
Click on the first or last page to see other LC-32LD135K (serv.man2) service manuals if exist.