Sharp LC-32GA6E (serv.man2) Service Manual ▷ View online
25
LC-26GA5E
LC-32GA5E
LC-32GA5E
LC-26GA6E
LC-32GA6E
LC-37GA6E
Use the up / down arrows to select a term in the
menu.
Confi rm the selection with
menu.
Confi rm the selection with
OK.
Use the left / right arrows to change between pa-
rameters.
Use the up / down arrows to change values.
rameters.
Use the up / down arrows to change values.
Press END button to return to the previous menu.
NVM Menu
To change NVM values.
ADDR:
NVM address.
VAL: NVM
Value.
SAVE:
Save NVM changes.
HDMI NVM WP:
Unprotect the EDID, that contains the recognizable formats of screen for HDMI.
ERASE:
If you select YES and Turn OFF-ON the TV by main switch, the data of NVM will be recorded
to the default values .
In
ADDR option of this menu, by using the colour buttons of R/C is possible to pass directly to A, B, C or D param-
eter.
Note: DO NOT change any NVM data, unless you have been advised to do by a Sharp representative. If data is
incorrectly changed, serious damage may occur to the receiver.
Note: DO NOT change any NVM data, unless you have been advised to do by a Sharp representative. If data is
incorrectly changed, serious damage may occur to the receiver.
DEVICE:
To select QS peripherals ICs. ( 0:LCD Controller / 1:QS Driver / 2: Extended Digital Analog Converter /
3: EEprom Microcontroller / 4: Reserved)
ADDR:
Address of register.
DATA:
Read mode: Display data after executing “SEND” / Write mode: Select data to write.
R/W:
Select Read or Write. ON: write OFF: read.
SEND:
Send data to QS.
Use the up / down arrows to select a term in the
menu.
Confi rm the selection with
menu.
Confi rm the selection with
OK.
Use the up / down arrows to change values.
Use the left / right arrows to change between pa-
rameters.
Use the left / right arrows to change between pa-
rameters.
IC Cont Menu (NOT OPERATIVE)
Send specifi c data to the QS board.
Send specifi c data to the QS board.
Press END button to return to the previous menu.
IC CONT
DEVICE 0
ADDR
ADDR
000
DATA
00
R/W
OFF/ON
SEND
GA6 VX.XX ExpX
PxW Exp X.X LCD VXX
PxW Exp X.X LCD VXX
MENU NVM
ADDR:
_ _ _ _
VAL
:
_ _
SAVE
HDMI NVM WP
HDMI NVM WP
YES
ERASE
NO
A B C D E F
GA6 VX.XX ExpX
PxW Exp X.X LCD VXX
PxW Exp X.X LCD VXX
M T
FREQ: Change between 50/60Hz and PC.
CLR MODE: When press OK key send the value to monitor microcontroller.
PATTERN1: Choose pattern to adjust QS.
PATTERN2: Choose pattern to adjust QS.
COMBIAS: Specifi c adjustment for QS. COMMON BIAS adjusting value is displayed.
IC CONT: See the next OSD.
SOFT VER.: Software version of QS IC. Display the version of monitor microcontroller.
CLR MODE: When press OK key send the value to monitor microcontroller.
PATTERN1: Choose pattern to adjust QS.
PATTERN2: Choose pattern to adjust QS.
COMBIAS: Specifi c adjustment for QS. COMMON BIAS adjusting value is displayed.
IC CONT: See the next OSD.
SOFT VER.: Software version of QS IC. Display the version of monitor microcontroller.
COMBIAS Adjustment
Select COMBIAS and press the “OK” button so that the fl icker screen will appear.
Adjust the fl icker on the screen to minimum with up / down buttons on the remote control. At this time, press the “OK”
key to complete the adjustment.
Select COMBIAS and press the “OK” button so that the fl icker screen will appear.
Adjust the fl icker on the screen to minimum with up / down buttons on the remote control. At this time, press the “OK”
key to complete the adjustment.
26
LC-26GA5E
LC-32GA5E
LC-32GA5E
LC-26GA6E
LC-32GA6E
LC-37GA6E
LC-32GA6E
LC-37GA6E
COUNTERS
SW FROM MAINS
XXXXX
SW ON TIMES
XXXXX
SW OFF TIMES
XXXXX
WORKING HOURS
XXXXX
FAC. DATE DDMY
XXXX
GA6 VX.XX ExpX
PxW Exp X.X LCD VXX
PxW Exp X.X LCD VXX
Use the up / down arrows to select a term in the
menu.
Confi rm the selection with
menu.
Confi rm the selection with
OK.
Press END button to return to the previous menu.
CPLD: NOT OPERATIVE
STOP BUS: Stop IC communication.
EXT 2 RGB: Enable or disable the RGB entry over EXT2 connector.
FLASH UPGRADE: Select ON to update to software update. (See page 23)
RAM TEST: Check the RAM memory. It is working correctly when “OFF” appear on the screen. If any number appear,
the memory is not working correctly.
STOP BUS: Stop IC communication.
EXT 2 RGB: Enable or disable the RGB entry over EXT2 connector.
FLASH UPGRADE: Select ON to update to software update. (See page 23)
RAM TEST: Check the RAM memory. It is working correctly when “OFF” appear on the screen. If any number appear,
the memory is not working correctly.
Counters Menu
To see information about TV.
To see information about TV.
OTHERS
CPLD
MENU
KEYS
STOP
BUS
VPS_8/30
EXT 2 RGB
EXT 2 RGB
OFF
FLASH UPGRADE
OFF
RAM
TEST
OFF
COUNTERS
GA6 VX.XX ExpX
PxW Exp X.X LCD VXX
PxW Exp X.X LCD VXX
SW FROM MAINS: Number of times that turn on the TV by the main switch.
SW ON TIMES: Number of times that switch on the TV by the R/C.
SW OFF TIMES: Number of times that switch on the TV by the R/C.
WORKING HOURS: Number of hours that is working the TV.
FAC. DATE DDMY: TV manufacture date (day, month, year).
SW ON TIMES: Number of times that switch on the TV by the R/C.
SW OFF TIMES: Number of times that switch on the TV by the R/C.
WORKING HOURS: Number of hours that is working the TV.
FAC. DATE DDMY: TV manufacture date (day, month, year).
Press END button to return to the previous menu.
KEYS Menu
Control menu of good operation of the top panel control keys.
If, when a key of the panel is pressed, the value who appears is within the parameters that appear in this menu, the
operation of this key is correct. High values near FF means, no key pressed.
Control menu of good operation of the top panel control keys.
If, when a key of the panel is pressed, the value who appears is within the parameters that appear in this menu, the
operation of this key is correct. High values near FF means, no key pressed.
Press END button to return to the previous menu.
MENU KEYS
ADC1:
F5
ADC2:
F5
GA6 VX.XX ExpX
PxW Exp X.X LCD VXX
PxW Exp X.X LCD VXX
27
LC-26GA5E
LC-32GA5E
LC-32GA5E
LC-26GA6E
LC-32GA6E
LC-37GA6E
HOTEL MODE :
To activate or to deactivate the HOTEL MODE.
POWER ON FIXED: Disable power on/off button of remote control.
MAX VOLUME :
MAX VOLUME :
To limit the maximum volume.
VOLUME FIXED:
Fix volume level.
VOL. FIX. VALUE: Value of “VOLUME FIXED”
RC BUTTON:
RC BUTTON:
To activate or to deactivate all remote control keys.
PANEL BUTTON: Disable all buttons on the main unit.
MENU KEYS:
MENU KEYS:
Disable “MENU” button on main unit and remote control.
OSD: Disable the OSD displaying.
IN. MODE START: Specify starting channel when power button is switched.
IN. MODE FIXED: Allows start with the input specifi ed in “INPUT MODE START” and prohibit to change channel
IN. MODE START: Specify starting channel when power button is switched.
IN. MODE FIXED: Allows start with the input specifi ed in “INPUT MODE START” and prohibit to change channel
and
input.
VPS
0300
00
0000
0000
GA6 VX.XX ExpX
PxW Exp X.X LCD VXX
PxW Exp X.X LCD VXX
Only information about VPS. Changes are not allowed.
VPS Menu
Broadcasting code identifi cation.
Broadcasting code identifi cation.
HOTEL Menu
In this menu the Hotel Mode is activated or deactivated.
Confi rm the selection with
OK.
Use the up / down arrows to change between
ON/OFF.
ON/OFF.
Press END button to return to the previous menu.
MENU HOTEL
HOTEL MODE
OFF
POWER ON FIXED
OFF
MAX
VOLUME
100
VOLUME FIXED
NO
VOL. FIX. VALUE
000
RC
BUTTON
NO
PANEL BUTTON
NO
MENU
KEYS
NO
OSD
NO
IN. MODE START
Norm
IN. MODE FIXED
NO
GA6 VX.XX ExpX
PxW Exp X.X LCD VXX
PxW Exp X.X LCD VXX
28
LC-26GA5E
LC-32GA5E
LC-32GA5E
LC-26GA6E
LC-32GA6E
LC-37GA6E
LC-32GA6E
LC-37GA6E
HD Component White Balance
(
(
For White Balance adjust it is recomended to use GAMMA CONST menu)
Before to carry out the HD Component White Balance Adjustments, it is requested to achieve the Common bias and
ADC adjustments in this order.
ADC adjustments in this order.
Input Component signal format 720p / 50Hz (Pattern: White 20%.)
Change to EXT 4 in menu TV and set brightness and contrast to 50%.
Enter in adjustment process by remote control ( key). The following OSD appears:
Change to EXT 4 in menu TV and set brightness and contrast to 50%.
Enter in adjustment process by remote control ( key). The following OSD appears:
By up or down key choose Gamma R Lo or Gamma B Lo and adjust in order to become the reference value. Repeat as
far as reference level is required.Don’t change green colour. It must be as default value.
far as reference level is required.Don’t change green colour. It must be as default value.
Change pattern: White 80%.
By up or down key choose Gamma R Hi or Gamma B Hi and adjust in order to become the reference value. Repeat as
far as reference level is required.Don’t change green colour. It must be as default value.
By up or down key choose Gamma R Hi or Gamma B Hi and adjust in order to become the reference value. Repeat as
far as reference level is required.Don’t change green colour. It must be as default value.
PC White Balance
(For White Balance adjust it is recomended to use GAMMA CONST menu)
Before to carry out the PC White Balance Adjustments, it is requested to achieve the Common bias and ADC adjust-
ments in this order.
Before to carry out the PC White Balance Adjustments, it is requested to achieve the Common bias and ADC adjust-
ments in this order.
Input PC signal format -XGA (Pattern: White 20%.)
Change to PC Input in menu TV and set brightness and contrast to 50%.
Enter in adjustment process by remote control (browse key). The same White Balance Component HD OSD appears.
Change to PC Input in menu TV and set brightness and contrast to 50%.
Enter in adjustment process by remote control (browse key). The same White Balance Component HD OSD appears.
By up or down key choose Gamma R Lo or Gamma B Lo and adjust in order to become the reference value. Repeat as
far as reference level is required.Don’t change green colour. It must be as default value.
far as reference level is required.Don’t change green colour. It must be as default value.
Change pattern: White 80%.
By up or down key choose Gamma R Hi or Gamma B Hi and adjust in order to become the reference value. Repeat as
far as reference level is required.Don’t change green colour. It must be as default value.
By up or down key choose Gamma R Hi or Gamma B Hi and adjust in order to become the reference value. Repeat as
far as reference level is required.Don’t change green colour. It must be as default value.
This Key (BROWSE) can be found in many CRT TV
Remote Control. We detail two of them below:
Remote Control. We detail two of them below:
Part Reference SN Price Code EX Price Code
RRMCG0739BMSA
AW
BT
RRMCG1022BMSA
**
BB
GAMMA R Lo XX
Click on the first or last page to see other LC-32GA6E (serv.man2) service manuals if exist.