DOWNLOAD Sharp LC-32DV200E Service Manual ↓ Size: 5.91 MB | Pages: 90 in PDF or view online for FREE

Approx.        W x D x H (mm)

796.2 x 243.0 x 596.6

w/o Stand,Handle Approx.  W x D x H (mm)

796.2 x 105.5 x 546.6

Net  Approx.

12.5kg

 (27.2lbs)

Net w/o Stand,Handle Approx.

11.0kg

 (24.1lbs)

Gross Approx.

15.5kg

 (34.4lbs)

Gross w/Master Carton  (Approx.)

--- kg

 ( --- lbs)

Master Carton

No

Content

----

Sets

Material

--          /--

Dimensions      W x D x H(mm)

  --     x   --     x --  

Description of Origin

No

Gift Box

Yes

Material

Double/Brown

Dimensions      W x D x H(mm)

900 x 265 x 654

Design

As per Buyer's

Description of Origin

No 

Drop Test

Natural Dropping At 1 Corner / 3 Edges / 6 Surfaces

Height  (cm)

48

Container Stuffing

390

Sets/45' Trailer

w/Pallet

No

w/Wrapping

No

Cabinet

Cabinet Front

PC+ABS  94V0  NON-HALOGEN

Cabinet Rear

PS 94V0 NON-DECABROM

Stand

PC+ABS  94V0  NON-HALOGEN

PCB

Non-Halogen

No

Eyelet Yes

Environmental standard requirement

Green procurement of SHARP

Pb- Free

Phase3(PHASE3A)

Measures for Whisker

Yes

WEEE

Yes

1. Remove the 12 screws (1).
2. Remove the Back Cabinet Ass'y in the direction of arrow .

Be careful not to remove the LVDS cable forcibly, because
the LVDS cable may be damaged.

1-1: COVER INVERTER and COVER LVDS (Refer to Fig. 1-1)
1.

Remove the screws (1).

2.

Remove the Cover Inverter in the direction of arrow (A).

3.

Disconnect the following connectors: (CP3803).

4.

Remove the screws (2).

5.

Remove the Cover LVDS in the direction of arrow (B).

6.

Release the lock of connector disconnect the following
connector: (CP2804).

(1)

(2)

(A)

Back Cabinet Ass'y

(B)

Connector

Cover 

Cover LVDS

(1)

(1)

(1)

(1)

(1)

(1)

(1)

(1)

(1)

(1)

(1)

(1)

Front Cabinet 

(1)

(1)

1. Remove the 4 screws (1).
2. Remove the Angle-Hinge in the direction of arrow (A).
3. Remove the 5 screws (2).
4. Remove the Angle-LCD Bottom in the direction of arrow (B).
5. Remove the LCD Block in the direction of arrow (C).

Fig. 1-1

LVDS

Fig. 1-3

Front Cabinet Ass'y

(C)

Fig. 1-2

LCD Block

(B)

(1)

(1)

(2)

(1)

(1)

(2)

(2)

Angle-LCD-Bottom

(A)

(1)

Angle-Hinge

(2)

1.

Put the Cabinet Back Ass'y on the bottom.

1. Disconnect the following connectors:

2.

Short circuit the position shown in Fig. 1-4 using a

soldering iron. If you remove the DVD Deck with no

2. Remove the 6 screws (1).

soldering, the Laser may be damaged.

3. Remove the Power PCB in the direction of arrow.

3.

Disconnect the following connectors:
(CP2301, CP2302, CP2303, CP8501 and CP8502).

4.

Remove the 3 screws (1).

5.

Remove the DVD DECK Ass'y in the direction of
arrow (A).

6.

Remove the 4 screws (2).

7.

Unlock the 2 supports (3).

8.

Remove the DVD MT PCB in the direction of arrow (B).

9.

Remove the Shield LVDS in the direction of arrow (C).

10. Remove the Shield LVDS Bottom in the direction of arrow (D).

Power PCB

(1)

(1)

(1)

(A)

(1)

(C)

Shield LVDS

DVD MT PCB

Short circuit using a

ld i

i

Pick Up PCB

(1)

(1)

(1)

(1)

Fig. 1-5

Back Cabinet Ass'y

(2)

(1)

Shield LVDS 

(2)

(2)

(2)

(B)

(D)

(3)

(3)

1-6: MAIN PCB and TUNER PCB  (Refer to Fig. 1-6)
1. Disconnect the following connector: 

2. Remove the 2 screws (1).
3. Remove the Tuner PCB in the direction of arrow (A).
4. Remove the screw (2).
5. Remove the Spring Earth Tuner in the direction of arrow (B).
6. Remove the 3 screws (3).
7. Remove the Shield Main Bottom in the direction of arrow (C)
8. Remove the 6 screws (4).

9. Remove the Main PCB in the direction of arrow (D).
10. Remove the Plate Jack in the direction of arrow (E).

1.

Before your operation, please read "PREPARATION
OF SERVICING".

2.

Use the Lead Free solder.

3.

Manual soldering conditions

• Soldering temperature: 320 ± 20

o

C

• Soldering time: Within 3 seconds
• Soldering combination: Sn-3.0Ag-0.5Cu

4.

When Soldering/Removing of solder, use the drawing
equipment over the Pick Up Unit to keep the Flux 
smoke away from it.

5.

When installing the DVD Deck, remove all the soldering 
on the short circuit position after the connection of Pick 
Up PCB and DVD MT PCB connector.

Main PCB

Back Cabinet Ass'y

Fig. 1-6

(4)

Back Cabinet Ass'y

soldering iron.

Fig. 1-4

(1)

(2)

(1)

(3)

(4)

(4)

(3)

(3)

Tuner PCB

Spring EarthTuner 

Shield Main 

Bottom

(4)

(4)

(4)

Plate Jack

(B)

(A)

(C)

(D)

(E)

1.

Remove the 2 screw (1).

2.

Remove the Remocon PCB in the direction of arrow (A).

3.

Remove the 2 screws (2).

4.

Remove the Panel Side Ass'y in the direction of arrow (B).

5.

Remove the 3 screws (3).

6.

Remove the Operation PCB in the direction of arrow (C).

(A)

(B)

Back Cabinet Ass'y

(1)

Remocon PCB

(1)

(3)

(2)

(2)

(C)

Operation PCB

(3)

(3)

(3)

Panel Side 

Fig. 1-7