Sharp LC-26SH7E Service Manual ▷ View online
2008-03-14
LC-19S7E-BK LC-26S7E-BK LC-32S7E-BK
45
< During external connection > No picture on the monitor (1)
↓
No picture appears on SCART1 - connected monitor during the tuner (U/V) reception.
↓
TERMINAL_UNIT:
↓
↓NO
↓NO
< During external connection > No picture on the monitor (2)
SCART2:
↓
No picture from SCART1 appears on SCART2-connected monitor.
NOTE: Normally, if the screen during display is sent to SCART2, no picture is sent to SCART2.
NOTE: Normally, if the screen during display is sent to SCART2, no picture is sent to SCART2.
↓
TERMINAL_UNIT:
↓
↓NO
↓NO
Is CVBS signal output into pin (19) of CN1901 (SCART1)?
YES
Check the setting of an external input device that connects of
CN1901.
CN1901.
Refer to “The picture doesn't appear in all modes.”
Is TUNER_CVBS signal output into pin (21) of CN1901 (SCART1)?
YES
Check the line between CN1901 and TU1101.
Checklist:
1) Is the Signal Type (item) in MENU-Option-Input Select equal to Signal Type of an external device? …Set it to “CVBS”, “RGB”, “AUTO”.
2) Is ANT-CABLE disconnected or connected improperly? …Connect it correctly as per the operation manual.
3) The picture is sent to the monitor in a CVBS signal if the source during display is ATV, CVBS of SCART1-2, AV side.
1) Is the Signal Type (item) in MENU-Option-Input Select equal to Signal Type of an external device? …Set it to “CVBS”, “RGB”, “AUTO”.
2) Is ANT-CABLE disconnected or connected improperly? …Connect it correctly as per the operation manual.
3) The picture is sent to the monitor in a CVBS signal if the source during display is ATV, CVBS of SCART1-2, AV side.
When sent by component, etc., that signal is not sent to the monitor.
4) When the monitor picture is not sent and is not displayed on the monitor, refer to “No picture” for each terminal.
5) The video output from SCART1 is not the monitor output (output of the picture now watching).
5) The video output from SCART1 is not the monitor output (output of the picture now watching).
The picture of the last selected TV channel is always sent to SCART1. (Specification)
Is CVBS signal output into pin (19) of CN1902 (SCART2)?
YES
Check the setting of an external input device that connects of
CN1902.
CN1902.
Refer to “The picture doesn't appear in all modes.”
Is CVBS signal output from pin (A13) of IC U4201 into pin (19) of
CN1902 (SCART2)?
CN1902 (SCART2)?
YES
Check the line between CN1902 and IC U4201.
Checklist:
1) Is the Signal Type (item) in MENU-Option-Input Select equal to Signal Type of an external device? …Set it to “CVBS”,.
2) The picture is sent to the monitor in a CVBS signal if the source during display is TV, CVBS of SCART1-2, AV side.
1) Is the Signal Type (item) in MENU-Option-Input Select equal to Signal Type of an external device? …Set it to “CVBS”,.
2) The picture is sent to the monitor in a CVBS signal if the source during display is TV, CVBS of SCART1-2, AV side.
When sent by component, etc., that signal is not sent to the monitor.
3) When the monitor picture is not sent and is not displayed on the monitor, refer to “No picture” for each terminal.
4) The video output from SCART1 is not the monitor output (output of the picture now watching).
4) The video output from SCART1 is not the monitor output (output of the picture now watching).
The picture of the last selected TV channel is always sent to SCART1. (Specification)
LC-19S7E-BK LC-26S7E-BK LC-32S7E-BK
46
CHAPTER 5.
MAJOR IC INFORMATIONS
[1] MAJOR IC INFORMATIONS
1. MAJOR IC INFORMATIONS
1.1. U4201 (MST9A885GL)
GENERAL DESCRIPTION
The MST9A885GL is a high performance and fully intergrated IC for multi-function LCD monitor/TV with resolution up to SXGA
(1280x1024)/WXGA+(1400x990). It is configured with an integrated triple-ADC/PLL,an integrated DVI/HDCP/HDMI receiver.a multi-standard TV video and
audio decoder,a video de-interlacer,a scalling engine,the MStarACE-3 color engine,an on –screen display controller,an 8-bit MCU and a built –in output
panel interface.By use of external frame buffer,3-D video decoding and processing are fulfilled for high-quality TV applications.To futher reduce system
costs,the MST9A885GL als integrates intelligent power management control capability for green-mode requirements and spread-mode requirements and
spread-spectrum support for EMI management.
The MST9A885GL is a high performance and fully intergrated IC for multi-function LCD monitor/TV with resolution up to SXGA
(1280x1024)/WXGA+(1400x990). It is configured with an integrated triple-ADC/PLL,an integrated DVI/HDCP/HDMI receiver.a multi-standard TV video and
audio decoder,a video de-interlacer,a scalling engine,the MStarACE-3 color engine,an on –screen display controller,an 8-bit MCU and a built –in output
panel interface.By use of external frame buffer,3-D video decoding and processing are fulfilled for high-quality TV applications.To futher reduce system
costs,the MST9A885GL als integrates intelligent power management control capability for green-mode requirements and spread-mode requirements and
spread-spectrum support for EMI management.
FEATURES
Single display LCD TV controller with PC &multimedia display functions
Input supports up to SXGA & 1080P
Panel supports up to SXGA(1280x1024) /WXGA+(1440x900)
TV decoder with 3-D comb filter
Multi-standard TV sound demodulator and decoder
10-bit triple-ADC for TV and RGB/YPbPr
10-bit video data processing
Integrated DVI/HDCP/HDMI compliant receiver
High-quality scaling engine & 3-D video de-interlacer
3-D video noise reduction
MStarACE-3 picture/color processing engine
Embedded On-Screen Display (OSD) control er engine
Built-in MCU supports PWM & GPIO
Built-in dual-link 8-bit LVDS transmitter
5-volt tolerant inputs
Low EMI and power saving features
256-pin LQFP
NTSC/PAL/SECAM Video Decoder
Supports NTSC M, NTSC-J, NTSC-4.43, PAL (B,D,G,H,M,N,I,Nc), and SECAM
Automatic TV standard detection
Motion adaptive 3-D comb filter for NTSC/PAL
8 configurable CVBS & Y/C S-video inputs
Supports Teletext level-1.5, WSS, VPS,Closed-caption, and V-chip
CVBS video output
Video IF for Multi-Standard Analog TV
Digital low IF architecture
Stepped-gain PGA with 26 dB tuning range and 1 dB tuning resolution
Maximum IF analog gain of 37dB in addition to digital gain
Programmable TOP to accommodate different tuner gain to optimize noise and linearity performance
Multi-Standard TV Sound Decoder
Supports BTSC/NICAM/A2/EIA-J demodulation and decoding
FM stereo & SAP demodulation
L/Rx4, mono, and SIF audio inputs
L/Rx3 loudspeaker and line outputs
Supports sub-woofer output
Built-in audio output DAC’s
Audio processing for loudspeaker channel, including volume, balance, mute, tone, EQ,and virtual stereo/surround
Optional advanced surround available (Dolby1, SRS2, BBE3… etc) Note
2008-03-14
LC-19S7E-BK LC-26S7E-BK LC-32S7E-BK
47
Digital Audio Interface
I2S digital audio input & output
S/PDIF digital audio input & output
HDMI audio channel processing capability
Programmable delay for audio/video synchronization
Analog RGB Compliant Input Ports
Three analog ports support up to 150MHz
Supports PC RGB input up to SXGA@75Hz
Supports HDTV RGB/YPbPr/YCbCr
Supports Composite Sync and SOG(Sync-on-Green) separator
Automatic color calibration
DVI/HDCP/HDMI Compliant Input Port
Supports TMDS clock up to 225MHz @ 1080P 60Hz with 12-bit deep-color resolution
Single link on-chip DVI 1.0 compliant receiver
High-bandwidth Digital Content Protection(HDCP) 1.1 compliant receiver
High Definition Multimedia Interface (HDMI)1.3 compliant receiver with CEC support
Long-cable tolerant robust receiving
Support HDTV up to 1080P
Auto-Configuration/Auto-Detection
Auto input signal format and mode detection
Auto-tuning function including phasing,positioning, offset, gain, and jitter detection
Sync detection for H/V Sync
Digital Video Input
One 4:2:2 ITU-R BT.656 8-bit digital video input port
High-Performance Scaling Engines
Fully programmable shrink/zoom capabilities
Nonlinear video scaling supports various modes including Panorama
Video Processing & Conversion
3-D motion adaptive video de-interlacer
Edge-oriented adaptive algorithm for smooth low-angle edges
Automatic 3:2 pull-down & 2:2 pull-down detection and recovery
MStar 3rd Generation Advanced Color Engine(MStarACE-3) automatic picture enhancement gives:
-Brilliant and fresh color
-Intensified contrast and details
-Vivid skin tone
-Sharp edge
-Enhanced depth of field perception
-Accurate and independent color control
sRGB compliance allows end-user to experience the same colors as viewed on CRTs and other displays
Programmable 12-bit RGB gamma CLUT
3-D video noise reduction
Frame rate conversion
On-Screen OSD Controller
16/256 color palette
256/512 1-bit/pixel font
128/256 4-bit/pixel font
Supports texture function
Supports 4K attribute/code
Horizontal and vertical stretch of OSD menus
Pattern generator for production test
Supports OSD MUX and alpha blending capability
Supports blinking and scrolling for closed caption applications
LC-19S7E-BK LC-26S7E-BK LC-32S7E-BK
48
LVDS/TTL Panel Interface
Supports 8-bit dual link LVDS up to SXGA(1280x1024) / WXGA+(1440x900)
Supports 8-bit single TTL panel
Supports 2 data output formats: Thine & TI data mappings
Compatible with TIA/EIA
With 6/8 bits options
Reduced swing for LVDS for low EMI
Supports flexible spread spectrum frequency with 360Hz~11.8MHz and up to 25% modulation
Integrated Micro Controller
Embedded 8032 micro controller
Configurable PWM’s and GPIO’s
Low-speed ADC inputs for system control
SPI bus for external flash
Supports external MCU option controlled through 4-wire double-data-rate direct MCU bus
External Connection/Component
SD/MMC/MS/MSPro card reader interface to support JPEG playback
Two USB controllers (1.1 OTG and 2.0 host) with the flexibility for connecting external storage devices or PictBridge
16-bit data bus for external frame buffer (DDR DRAM)
All system clocks synthesized from a single external clock
1.2. U6102 (TPA3124D2PWPR)
Description
The TPA3124D2 is a 15-W(per channel);efficient,class-D audio power amplifier for driving stereo speakers in a single-ended configuration;or a
mono speaker in a bridage-tied-load configuration .The TPA3124D2 eliminates the need for an external heat sink when playing music.
mono speaker in a bridage-tied-load configuration .The TPA3124D2 eliminates the need for an external heat sink when playing music.
The gain of amplifier is controlled by two gain select pins.The gain selections are 20.26.32and 36dB.
The patented start-up and shutdown sequences minimize pop noise in the speakers without additional circuity.
Features
10-W/Ch Into a 8-Ω Load From a 24-V Supply
15-W/Ch Into a 4-Ω Load From a 22-V Supply
30-W/Ch Into a 8-Ω Load From a 22-V Supply
Operates From 10V to 26V
Can Run From +24V LCD Backlight Supply
Efficient Class-D Operation Eliminates Need For Heat Sinks
Four selectable,Fixed-Gain Settings
Internal Oscillator(No External Components Required)
Single-Ended Analog Imputs
Thermal and Short-Circuit Portection With Auto Recovery
Space-Saving Surface Mount 24-Pin TSSOP Package
Advanced Power-Off Pop Reduction
Applications
10-W/Ch Into a 8-Ω Load From a 24-V Supply
15-W/Ch Into a 4-Ω Load From a 22-V Supply
30-W/Ch Into a 8-Ω Load From a 22-V Supply
Operates From 10V to 26V
Can Run From +24V LCD Backlight Supply
Efficient Class-D Operation Eliminates Need For Heat Sinks
Four selectable,Fixed-Gain Settings
Internal Oscillator(No External Components Required)
Single-Ended Analog Imputs
Thermal and Short-Circuit Portection With Auto Recovery
Space-Saving Surface Mount 24-Pin TSSOP Package
Advanced Power-Off Pop Reduction
Applications
Flat Panel Televisions
DLP TVs
CRT TVs
Powered Speakers
DLP TVs
CRT TVs
Powered Speakers
1.3. U1503 (TMDS261)
Description
The TMDS261 is a two-port digital video interface (DVI) or high-definition multimedia interface (HDMI) switch that allows up to two DVI or HDMI
ports to be switched to a single display terminal. Four TMDS channels, one hot-plug detector, and a digital display control (DDC) interface are
supported on each port. Each TMDS channel supports signaling rates up to 3 Gbps to allow 1080p resolution in 16-bit color depth.
The TMDS261 provides an adaptive equalizer for different ranges of cable lengths. The equalizer automatically compensates for intersymbol
interference [ISI] loss of an HDMI/DVI cable for up to 20 dB at 3 Gbps
ports to be switched to a single display terminal. Four TMDS channels, one hot-plug detector, and a digital display control (DDC) interface are
supported on each port. Each TMDS channel supports signaling rates up to 3 Gbps to allow 1080p resolution in 16-bit color depth.
The TMDS261 provides an adaptive equalizer for different ranges of cable lengths. The equalizer automatically compensates for intersymbol
interference [ISI] loss of an HDMI/DVI cable for up to 20 dB at 3 Gbps
Features
2:1 Switch Supporting DVI Above 1920 × 1200 · 64-Pin TQFP Package: Pin-Compatible With and HDMI HDTV Resolutions up to 1080p With
2:1 Switch Supporting DVI Above 1920 × 1200 · 64-Pin TQFP Package: Pin-Compatible With and HDMI HDTV Resolutions up to 1080p With
TMDS25116-bit Color Depth · Robust TMDS Receive Stage That Can Work
Designed for Signaling Rates up to 3 Gbps With Non-Compliant Input Common-Mode
HDMI1.3a Spec Compliant HDMI Signal
Adaptive Equalization to Support up to 20-m HDMI Cable
TMDS Input Clock-Detect Circuit · High-Definition Digital TV
Click on the first or last page to see other LC-26SH7E service manuals if exist.