DOWNLOAD Sharp LC-26SH7E Service Manual ↓ Size: 21.71 MB | Pages: 127 in PDF or view online for FREE

         2008-03-14 

LC-19S7E-BK LC-26S7E-BK LC-32S7E-BK 

 49 

 DDC Repeater Function –– LPClaDsma 

<2 mW Low-Power Mode – DLP® 

Local I2C or GPIO Configurable 

Enhanced ESD. HBM: 10 kV on All Input TMDS, DDC I2C, HPD Pins 

3.3-Volt Power Supply 

Temperature Range: 0°C to 70°C 

64-Pin TQFP Package: Pin-Compatible With TMDS251 

Robust TMDS Receive Stage That Can Work With Non-Compliant Input Common-Mode HDMI Signal 

1.4. U1901,U1201,U6101,U6103 (DRV601RTJR) 

General description 

The DRV601 is a stereo line driver designed to allow the removal of the output dc-blocking capacitors for reduced component count and cost. The 

device is ideal for single supply electronics where size and cost are critical design parameters. 

The DRV601 is capable of driving 2 Vrms into a 600-Ω load at 3.3 V. The device has external gain setting resistors, that support a gain range of -

1V/V to -10V/V, and line outputs that has ±8-kV IEC ESD protection. The device has independent shutdown control for the right and left audio 

channels. 

The DRV601 is available in a 4 mm ´ 4 mm Thin QFN package. 

Features 

External Gain Setting Resistors 

        Space Saving Package 

-20-Pin, 4 mm ´ 4 mm Thin QFN, Thermally Optimized PowerPAD™ Package 

Ground-Referenced Outputs Eliminate DC-Blocking Capacitor 

-Reduce Board Area 

-Reduce Component Cost 

-Improve THD+N Performance 

-No Degradation of Low-Frequency Response Due to Output Capacitors 

Wide Power Supply Range: 1.8 V to 4.5 V 

2 Vrms/Ch Output Voltage into 600 Ω at 3.3 V supply 

Independent Right and Left Channel Shutdown Control 

Short-Circuit and Thermal Protection 

Pop Reduction Circuitry 

Applications 

         Set-Top Boxes 

CD / DVD Players 

DVD-Receivers 

HTIB 

PDP / LCD TV's 

1.5. U7101 (TPS62203DBVRG4) 

The TPS6220x devices are a family of high-efficiency

 

synchronous step-down converters ideally suited for

 

portable systems powered by 1-cell Li-Ion 

or 3-cell

 

NiMH/NiCd batteries. The devices are also suitable

 

to operate from a standard 3.3-V or 5-V voltage rail. 

         With an output voltage range of 6 V down to 0.7 V and up to 300 mA output current, the devices are ideal to power low voltage DSPs and processors 

used in PDAs, pocket PCs, and smart phones.  

         Under Nominal load current,the devices operate with a fixed switching frequency of typically 1 MHz .At light load currents,the part enters the power 

save mode operation,the switching frequency is reduced and quiescent current is typically  only 15uA;therefore, it achieves the highest  efficiency 

over the entire load current range.The TPS 6220X needs only three small external components.Together with the SOT23 package,a minimum 

system solution size is achieved.An advanced fast response voltage mode control scheme achieves superior line and load regulation with small 

ceramic input  and output capacitors. 

 

 

 

 

LC-19S7E-BK LC-26S7E-BK LC-32S7E-BK 
 

50  

           High Efficiency Synchronous Step-Down Converter With up to 95% Efficiency 

           2.5-V to 6-V Input Voltage Range 

           Adjustable Output Voltage Range From 0.7 V to V1 

Fixed Output Voltage Options Available 

        

 Up to 300 mA Output Current 

             -MHz Fixed Frequency PWM Operation

 

         

Highest Efficiency Over Wide Load Current Range Due to Power Save Mode 

15-μA Typical Quiescent Current 

         

Soft Start 

100% Duty Cycle Low-Dropout Operation 

Dynamic Output-Voltage Positioning 

Available in a 5-Pin SOT23 Package 

PDAs and Pocket PC 

             Cellular Phones, Smart Phones 

Low Power DSP Supply 

Digital Cameras 

Portable Media Players 

Portable Equipment 

1.6. U7103 (SC4524BSETRT) 

             The SC4524B is a constant frequency peak current-mode step-down switching regulator capable of producing 2A output current from an input 

ranging from 3V to 16V. The switching frequency of the SC4524B is programmable up to 2MHz, allowing the use of small inductors and ceramic 

capacitors for miniaturization, and high input/output conversion ratio. The SC4524B is suitable for next generation XDSL modems, high-definition 

TVs and various point of load applications. 

Peak current-mode PWM control employed in the SC4524B achieves fast transient response with simple loop compensation. Cycle-by-cycle 

current limiting and hiccup overload protection reduces power dissipation during output overload. Soft-start function reduces input start-up current 

and prevents the output from overshooting during power-up. 

 

        Wide input range: 3V to 16V 

2A Output Current  

200kHz to 2MHz Programmable Frequency 

Precision 1V Feedback Voltage 

Peak Current-Mode Control 

Cycle-by-Cycle Current Limiting 

Hiccup Overload Protection with Frequency Foldback 

Soft-Start and Enable 

Thermal Shutdown 

Thermally Enhanced 8-pin SOIC Package 

Fully RoHS and WEEE compliant 

XDSL and Cable Modems 

Set Top Boxes 

Point of Load Applications 

CPE Equipment 

DSP Power Supplies 

LCD and Plasma TVs  

 

              The STMPS2141, STMPS2151, STMPS2161,STMPS2171 power distribution switches are intended for applications where heavy capacitive 

loads and short circuits are likely to be encountered. These devices incorporate 90 mΩ N-channel MOSFET high-side power switches for power- 

distribution. These switches are controlled by a logic enable input. 

         2008-03-14 

LC-19S7E-BK LC-26S7E-BK LC-32S7E-BK 

 51 

FEATURES 

90 mΩ high-side MOSFET switch 

500/1000 mA continuous current  

Thermal and short-circuit protection with overcurrent logic output 

Operating range from 2.7 V to 5.5 V 

CMOS- and TTL-compatible enable inputs 

Undervoltage lockout (UVLO) 

12 μA maximum standby supply current 

Ambient temperature range, -40°C to 85°C 

8 kV ESD protection 

Reverse current protection 

Fault-blanking 

              The AT24C02B provides 2048 bits of serial electrically erasable and programmable read-only memory (EEPROM) organized as 256 words of 8 

bits each. The device is optimized for use in many industrial and commercial applications where low-power and low-voltage operation are 

essential. The AT24C02B is available in space-saving 8-lead PDIP, 8-lead JEDEC SOIC, 8-lead Ultra-Thin Mini-MAP (MLP 2x3), 5-lead SOT23, 

8-lead TSSOP, and 8-ball dBGA2 packages and is accessed via a Two-wire serial interface. In addition, the AT24C02B is available in 1.8V (1.8V 

to 5.5V) version. 

FEATURES 

  Low-voltage and Standard-voltage Operation 

–

 1.8 (VCC = 1.8V to 5.5V) 

Internally Organized 256 x 8 (2K) 

Two-wire Serial Interface 

Schmitt Trigger, Filtered Inputs for Noise Suppression 

Bidirectional Data Transfer Protocol 

1 MHz (5V), 400 kHz (1.8V, 2.5V, 2.7V) Compatibility 

Write Protect Pin for Hardware Data Protection 

8-byte Page (2K) Write Modes 

Partial Page Writes Allowed 

Self-timed Write Cycle (5 ms max) 

High-reliability 

–

 Endurance: 1 Million Write Cycles 

–

 Data Retention: 100 Years 

8-lead PDIP, 8-lead JEDEC SOIC, 8-lead Ultra-Thin Mini-MAP (MLP 2x3), 5-lead SOT23, 8-lead TSSOP and 8-ball dBGA2 Packages 

Lead-free/Halogen-free 

Available in Automotive 

Die Sales: Wafer Form, Waffle Pack and Bumped Wafers 

1.9. U4402 (W25X16AVSSIG SO-8 208mil) 

The W25X16A (16M-bit) Serial Flash memory provide a storage solution for systems with limited space, pins and power. The 25X series offers 

flexibility and performance well beyond ordinary Serial Flash devices. They are ideal for code download applications as well as storing voice, text 

and data. The devices operate on a single 2.7V to 3.6V power supply with current consumption as low as 5mA active and 1μA for power-down. 

All devices are offered in space-saving packages. 

The W25X16A array is organized into 8,192 programmable pages of 256-bytes each. Up to 256 bytes can be programmed at a time using the 

Page Program instruction. Pages can be erased in groups of 16 (sector erase), groups of 256 (block erase) or the entire chip (chip erase). The 

W25X16A has 512 erasable sectors and 32 erasable blocks. The small 4KB sectors allow for greater flexibility in applications that require data 

and parameter storage. (See figure 2.) 

The W25X16A supports the standard Serial Peripheral Interface (SPI), and a high performance dual output SPI using four pins: Serial Clock, Chip 

Select, Serial Data I/O and Serial Data Out. SPI clock frequencies of up to 100MHz are supported allowing equivalent clock rates of 200MHz 

when using the  Fast Read Dual Output instruction. These transfer rates are comparable to those of 8 and 16-bit Parallel Flash memories. 

A Hold pin, Write Protect pin and programmable write protect, with top or bottom array control features, provide further control flexibility. 

LC-19S7E-BK LC-26S7E-BK LC-32S7E-BK 
 

52  

Additionally, the device supports JEDEC standard manufacturer and device identification. 

FEATURES 

Family of Serial Flash Memories 

– W25X16A: 16M-bit / 2M-byte (2,097,152) 

– 256-bytes per programmable page 

– Uniform 4K-byte Sectors / 64K-byte Blocks 

SPI with Single or Dual Outputs 

– Clock, Chip Select, Data I/O, Data Out 

– Optional Hold function for SPI flexibility 

Data Transfer up to 200M-bits / second 

– Clock operation to 100MHz 

– Fast Read Dual Output instruction 

– Auto-increment Read capability 

Flexible Architecture with 4KB sectors 

– Sector Erase (4K-bytes) 

– Block Erase (64K-byte) 

– Page program up to 256 bytes <2ms 

– More than 100,000 erase/write cycles 

– More than 20-year data retention 

Low Power Consumption,Wide Temperature Range 

– Single 2.7 to 3.6V supply 

– 5mA active current, 1μA Power Down(typ) 

– -40° to +85°C operating range 

Software and Hardware write Protection  

– Write-Protect all or portion of memory  

– Enable/Disable protection with /WP pin 

– Top or bottom array protection 

Space Efficient Packaging 

– 8-pin SOIC 150-mil 

– 8-pin SOIC 208-mil 

– 8-pin PDIP 300-mil 

– 16-pin SOIC 300-mil 

– 8-pad WSON 6x5-mm