DOWNLOAD Sharp LC-26SH7E Service Manual ↓ Size: 21.71 MB | Pages: 127 in PDF or view online for FREE

         2008-03-14 

LC-19S7E-BK LC-26S7E-BK LC-32S7E-BK 

 25 

 

2）

 Equipment 

Requirements: 

Color 

analyzer. 

 Input 

requirements: 

 

For SZ factory:  
Signal Type      : RF signal 

            Set to PAL D/K system, frequency=184.25MHz ( for China 

model ) with white pattern of 80% 

              

Set to PAL B/G system, frequency=64.25MHz ( for AP

 

model ) with white pattern of 80% 

Input Signal Strength : 10mV  (80 dBuV) terminal voltage. 

 

Input Injection Point  : TV Tuner input 
For FQ factory:  
Signal Type      : CVI (YPbPr) 

U

sing Quantum Data Pattern Generator 802G or 802R or 882; 

Set to 576i with white pattern of 80% (flat patten) 

Apply full white pattern, select smart setting to be Standard. Adjusting SCALER GAIN R G B to reach 

W/D and luminance in  factory mode as below. 

Adjust Color Temp in the factory Mode OSD by adjusting GAIN  R xxx  G xxx  B xxx in  

factory mode (Fig. 4)  

 

CIE1391 chromaticity (x,y) shall be 

0.272 + 0.01 

0.277+ 0.01    

0.289 + 0.01 

0.291 + 0.01    

0.314 + 0.01 

0.319 + 0.01    

 

~ R/G/B Gain value <= 127 to avoid satsuation at 32-grey pattern. 

 

~At TV Luminance at Normal >= 250 cd/m

2

 when contrast and brightness and color are 100%.  

  ~

At PC Luminance at Normal >= 250 cd/m

2

 when contrast and brightness are 100%.

 

~ 

These group settings about color temp are also applied automatically into  

                  HDMI1/CVI(for SZ factory)/SIDE AV/PC/TV(for FQ factory). That means TV/HDMI/CVI/PC are 

used the same setting. 

 

LC-19S7E-BK LC-26S7E-BK LC-32S7E-BK 
 

26  

Enter factory mode menu: Press the key “1999” on remote control. 

 

 

 

 

 

 

 

 

 

Press  ↑, ↓ to choose the value

 

Press  OK  to fix the value.

 

Press  OK  to exit the factory mode when choose “exit” value,  

 

 

 

 

 

 

 

 

 

 

 

 

         2008-03-14 

LC-19S7E-BK LC-26S7E-BK LC-32S7E-BK 

 27 

 

Please follow the following step to upgrade the firmware. 

1. Copy the software firmware (*.bin) to USB Disk.  

2. Insert the USB Disk to TV USB port.

 

 

 

 

3. Unplug the AC cord. 

4.  AC power on 

5. Reboot TV to update SW automatically. During upgrade FW the front LED will red light blink. 

6. When FW upgrade is finished LED will stop blinking and keep at  (Blue + red) color. 

After finish upgrade process. 

7. Remove USB disk from TV. 

8. Turn AC Off then On to reboot TV 

LC-19S7E-BK LC-26S7E-BK LC-32S7E-BK 
 

28  

CHAPTER 4. 

 

 

[1] TROUBLESHOOTING TABLE（19”） 

↓ 

 
 

LINE_FILTER_UNIT:          

↓ YES

 

 
 
 
 
 

 

POWER_UNIT                 

↓YES

  

 
 
 

↓YES 

 
 
 
 

↓YES 

 
 
 
 

 

Are the power cord and harness in the unit properly connected? 

NO 

Connect the power cord and harness properly, and turn on the 
power.

Is F901 normal? 

NO 

 

LINE_FILTER_UNIT: 
Isn't C908, RV901, L902, C900, C901, etc. out of order? 
Moreover, whether the short-circuit with the circumference circuit 
is checked. 

Is BD901 (+320V) output?  
 
*  When power on/off switch is on  ‧‧‧ About +400V 

Does the circuit operate normally? 
Check circuit around (FB901, Q906, ZD904, IC901 etc ). 

 

NO 

 

Is a voltage of +5.3V applied to pin (3,4) of connector (CN902)? 

Does the switching circuit operate normally? 
Check circuit around the primary side (T901, ZD906, D901, 
D903, Q903, D904, IC901, IC902, D905 etc.), the secondary 
side (D905, L904, etc.), the DC_DET circuit (IC902, ZD903, 
IC901, ZD902, etc.), and the protection circuit.

NO 

 

Is a voltage of +18V applied to pin (8,9) of connector (CN902)? 

 

NO 

 

Does the inverter circuit operate normally? 
Check circuit around (Q801, ZD801, ZD802, Q805, Q806, IC801, 
T801, L801, L802, etc.), and the protection circuit.