Sharp LC-26SH7E Service Manual ▷ View online
2008-03-14
LC-19S7E-BK LC-26S7E-BK LC-32S7E-BK
5
[2] OPERATION MANUAL
Remote control unit
POWER: Press to turn on/off the TV from or to standby mode.
VIDEO: Press to select Component / Side AV / HDMI1 /HDMI2 /HDMI3 input
SCART: Press to select SACRT1 / SCART2 input
PC: Press to select PC input
TV: Press to select TV input
Number Key: 1. Press number button to direct access to TV channel
2. Press the pass code to activate the factory mode
3. Press to activate the Channel Lock (enter PIN code for Channel lock)
4. If channel list OSD active – jump to that channel in the channel list (not tune
the channel until OK is pressed)
EPG: Press this key to display electronic program guide screen in DTV mode.
PRE PR: Press to alternate between the currently viewed channel and previously viewed
channel (It should return to previous view if it comes from different signal
source)
SOURCE: 1. Press repeatedly to select the signal source:
2. The Source List should be activated and show on OSD.
3. 1st press displays current, subsequent presses advance
ASPECT: Press to toggle among screen format Automatic/ Panoramic / 4:3 / Movie
expand 14:9 / Movie expand 16:9 / 16:9 subtitle /
wide screen
DUAL: Press to select mono / stereo / DUAL ATV channel. Select Audio language for
DTV channel.
SLEEP: Press to show the sleep-timer slider in the right side of screen. 1st press displays
current, subsequent presses advance (Loops)
(5-180 minutes.)
PICTURE: Press to set the LCD TV to a predefined picture setting. User / Cinema / Sport /
Vivid / Hi-Bright
PR List: Press to display a list of channels and input sources.
SOUND: Press to set the LCD TV to a predefined sound setting. Off / Rock / Pop / Live /
Dance / Techno / Classic / Soft
VOL +/ -: Press to adjust the volume
MUTE: Press to toggle audio on and off. You can also press +/- VOL to restore the previous
volume level.
DISPLAY: Press to display information about the selected TV channel (Channel banner)
LC-19S7E-BK LC-26S7E-BK LC-32S7E-BK
6
TV (Front view)
TV (Rear view)
1 Power connector 2 HDMI /HDMI 1
3 PC IN (VGA/AUDIO) 4 SCART, SCART
5 SCART 2 (CVBS 6 Component (Video
7 Tuner Input
8 AV VIDEO and L/R Audio Output
9 SERVICE socket 10 Earphone Output
11 Composite ( AV IN, AV/LR) 12 HDMI 2 (For 26” and 32” only)
(Standby/On) indicator
Remote control sensor
2008-03-14
LC-19S7E-BK LC-26S7E-BK LC-32S7E-BK
7
Preparation
Mount the TV Stand
1. Put the TV face down on a safe surface that
is covered by a soft and smooth cloth.
2. Adjust the TV stand to the base column of the TV.
3. Fasten screws by using a cross-head
Screwdriver(Not supplied).
Wall mounting
1. Put the TV face down on a safe surface that is
covered by a soft and smooth cloth.
2. Unscrew the 4 bolts that fasten the base
column to the TV by using a cross-head
screwdriver. (not supplide)
screwdriver. (not supplide)
3. Detach the stand from the bottom of the TV.
LC-19S7E-BK LC-26S7E-BK LC-32S7E-BK
8
preparation
Installation of batteries
1.
insert two AAA batteries into Remote control.
Make sure (+) and (-) are facing the proper
direction.
Make sure (+) and (-) are facing the proper
direction.
2. Replace the cover.
NOTE
• If the remote control will not to be used for a long
• If the remote control will not to be used for a long
time, remove the batteries to avoid remote control damage.
CAUTION
Improper use of batteries can result in chemical leakage or explosion. Be sure to follow the instructions below.
• Do not mix batteries of different types. Different types of batteries have different characteristics.
• Do not mix old and new batteries. Mixing old and new batteries can shorten the life of new batteries or cause
• Do not mix batteries of different types. Different types of batteries have different characteristics.
• Do not mix old and new batteries. Mixing old and new batteries can shorten the life of new batteries or cause
chemical leakage in old batteries.
• Remove batteries as soon as they have worn out. Chemicals that leak from batteries can cause a rash. If you find
any chemical leakage, wipe thoroughly with a cloth.
• The batteries supplied with this product may have a shorter life expectancy due to storage conditions.
• If you will not be using the remote control unit for an extended period of time, remove the batteries from it.
• If you will not be using the remote control unit for an extended period of time, remove the batteries from it.
Note on disposing batteries:
The batteries provided contain no harmful materials such as cadmium, lead or mercury.
Regulations concerning used batteries stipulate that batteries may no longer be thrown out with the household
Rubbish. Deposit any used batteries free of charge into the designated collection containers set up at commercial
Businesses.
Regulations concerning used batteries stipulate that batteries may no longer be thrown out with the household
Rubbish. Deposit any used batteries free of charge into the designated collection containers set up at commercial
Businesses.
Using the remote control unit Bundling the cables
Use the remote control unit by pointing it towards the
remote control sensor. Objects between the remote
control unit and sensor may prevent proper operation.
remote control sensor. Objects between the remote
control unit and sensor may prevent proper operation.
Remote control sensor
5m
30
30
Click on the first or last page to see other LC-26SH7E service manuals if exist.