Sharp LC-19D1EWH (serv.man6) Service Manual ▷ View online
LC-19D1E/S-BK/WH
5 – 10
2.5. IC502 (VHiM3221EIP-1Y)
2.5.1 Block Diagram
2.5.2 Pin Connections and short description
RS232C-DRIVER/RECEIVER
Pin No.
Pin Name
I/O
Pin Function
1
EN
I
Receiver Enable Control . Drive low for normal operation. Drive high to force the receiver outputs (R_OUT) into
a high-impedance state.
a high-impedance state.
2
C1+
-
Positive terminal of the voltage doubler Charge-Pump Capacitor
3
V+
-
+5.5V generated by the charge pump
4
C1-
-
Negative terminal of the voltage doubler Charge-Pump Capacitor
5
C2+
-
Positive terminal of inverting Charge-Pump Capacitor
6
C2-
-
Negative terminal of inverting Charge-Pump Capacitor
7
V-
-
-5.5V generated by the charge pump
8
R_IN
I
RS-232 Receiver Inputs
9
R_OUT
O
TTL/CMOS Receiver Outputs
10
INVALID
I
Output of the Valid Signal Detector. INVALID is enabled high if a valid RS-232 level is present on any receiver
input.
input.
11
T_IN
I
TTL/CMOS Transmitter Inputs
12
FORCEON
I
Drive high to override automatic circuitry keeping transmitters and charge pump on (FORCEOFF must be high)
13
T_OUT
O
RS-232 Transmitter Outputs
14
GND
-
Ground
15
VCC
-
+3.0V to +5.5V Supply Voltage
16
FORCEOFF
I
Force-Off Input, active low. Drive low to shut down transmitters, receivers (MAX3243E, except R2OUTB), and
on-board charge pump . This overrides all automatic circuitry and FORCE ON
on-board charge pump . This overrides all automatic circuitry and FORCE ON
LC-19D1E/S-BK/WH
5 – 11
2.6. IC701 (VHiBD9306AF-1Y)
2.6.1 Block Diagram
2.6.2 Pin Connections and short description
1ch Step Down switching regulato
Pin No.
Pin Name
I/O
Pin Function
1
RT
---
Timing Resistor external terminal.
2
CT
---
Timing Capacitor external terminal.
3
ENB
I
Control terminal.
4
GD
O
Gate drive output terminal.
5
VCC
---
Power supply terminal.
6
GND
---
Ground.
7
COMP
O
Error amplifier output terminal.
8
FB
I
Error amplifier inverting input terminal.
LC-19D1E/S-BK/WH
5 – 12
2.7. IC506, IC4605 (VHiNJM4565V-1Y)
2.7.1 Block Diagram
2.7.2 Pin Connections and short description
DUAL OP-AMP
Pin No.
Pin Name
I/O
Pin Function
1
A OUTPUT
O
A output
2
A +INPUT
I
A + input
3
A -INPUT
I
A - input
4
V-
-
Ground
5
B +INPUT
I/O
B + input
6
B -INPUT
I
B - input
7
B OUTPUT
I
B output
8
V+
-
Power supply
LC-19D1E/S-BK/WH
5 – 13
2.8. IC507 (VHiTL52055D-1Y)
2.8.1 Block Diagram
2.8.2 Pin Connections and short description
3-Video-SW
Pin No.
Pin Name
I/O
Pin Function
1
1B
I
1ch Input B.
2
1C
I
1ch Control Signal.
3
1Y
O
1ch Output.
4
GND2
I
2ch Ground
5
2Y
O
2ch Output.
6
3Y
O
3ch Output.
7
3C
I
3ch Contrl Signal.
8
3A
I
3ch Input A.
9
3B
I
3ch Input B.
10
GND3
-
3ch Ground.
11
2A
I
2ch Input A.
12
2C
I
2ch Contrl Signal.
13
VCC
-
Power supply .
14
2B
I
2ch Input B.
15
GND1
-
1ch Ground.
16
1A
I
1ch Input A.
Click on the first or last page to see other LC-19D1EWH (serv.man6) service manuals if exist.