DOWNLOAD Sharp XV-Z9000E (serv.man2) Service Manual ↓ Size: 1.69 MB | Pages: 31 in PDF or view online for FREE

1. Select the following group

and subject.
Group:

DLP

Subject:

R-GAIN
G-GAIN
B-GAIN

2. Feed the Component

video, 75% white signal.

3. Signal level: 0.7

±

0.05 Vp-p

(sync section not included)

4. R-GAIN, G-GAIN and B-

GAIN initial settings: 95

5. Target chromaticity:

x = 0.272 

±

 0.005

y = 0.310 

±

 0.005

(color temperature 9500K+15 

µ

V)

1. Project an image over a 40-inch screen and

measure the chromaticity at the center using a
chromaticity meter.

2. Keep the G-GAIN setting fixed at 95.
3. Adjust the B-GAIN setting to get the y value to its

target chromaticity.

4. Adjust the R-GAIN setting to get the x value to its

target chromaticity.

1. Feed the NTSC mono-

scope pattern signal.
INPUT4

2. Select the following group

and subject.
Group:

VIDEO 1

Subject: NTSC-H

1. Using the control switches on the set or the buttons

on the remote control, adjust the setting until the
overscan should be equal at right and left.

1. Feed the SMPTE pattern

signal.
INPUT5

2. Select the following group

and subject.
Group:

DLP

Subject:

R-BRIGHT
G-BRIGHT
B-BRIGHT

1. Make sure the 100% and 95% white and the 0%

and 5% black tones are visible.

2. If the black tone appears otherwise, finely adjust the

R-BRIGHT, G-BRIGHT and B-BRIGHT settings.

1. Feed the NTSC 10-step

gray-scale signal.

2. Select the following group

and subject.
Group:

VIDEO1

Subject: BRIGHT

1. Using the control switches on the set or the buttons

on the remote control, adjust the setting until more
bit dropouts start at the 0% black level.

1. Feed the NTSC 10-step

gray-scale signal.

2. Select the following group

and subject.
Group:

VIDEO1

Subject:

PICTURE

1. Using the control switches on the set or the buttons

on the remote control, adjust the setting until bit drop-
outs start at the 100% white level.

1. Feed the internal 8CH (split

color bar) signal.
INPUT4

2. Select the following group

and subject.
Group:

VIDEO1

Subject:

TINT

1. Check the fixed setting.

Fixed setting: 128

1. Feed the 100% color bar

signal (component signal)
or the 10-step gray scale
signal to the input terminal
480I.
INPUT2

2. Select the following group

and subject.
Group:

DVD

Subject:

BRIGHT

1. Using the control switches on the set or the buttons

on the remote control, adjust the setting until more
bit dropouts start at the 0% black level.

1. Check the fixed setting.

Fixed setting: 105

1. Feed the internal 8CH (split

color bar) signal.
INPUT4

2. Select the following group

and subject.
Group:

VIDEO1

Subject:

N-COLOR

1. Check the fixed setting.

Fixed setting: 110

1. Feed the PAL color bar sig-

nal.
INPUT4

2. Select the following group

and subject.
Group:

VIDEO1

Subject:

P-COLOR

1. Check the fixed setting.

Fixed setting: 110

1. Feed the SECAM color bar

signal.
INPUT4

2. Select the following group

and subject.
Group:

VIDEO1

Subject: S-COLOR

1. Feed the 100% color bar

signal (component signal)
or the 10-step gray scale
signal to the input terminal
480I.
INPUT2

2. Select the following group

and subject.
Group:

DVD

Subject:

CONTRAST

1. Using the control switches on the set or the buttons

on the remote control, adjust the setting until bit drop-
outs start at the 100% white level.

1. Feed the 100% color bar

signal (480I component
signal) to the Y, Pb and Pr
input terminals.
INPUT2

2. Select the following group

and subject.
Group:

DVD

Subject:

COLOR
TINT

1. Check the fixed settings.

Fixed setting:

TINT at 32
COLOR at 36

1. Heat the thermistor with a

hair dryer.

1. Make sure that the temperature is indicated.

1. Feed the phase check pat-

tern signal.

1. In the VGA, SVG Aand XGAmodes, make sure the

Clock, Phase, H-Pos and V-Pos settings can be au-
tomatically adjusted.

1. Make the following settings.

Destination

Adjustment process Remote control setting

XV-Z9000U

S4

 Factory setting 4

XV-Z9000E

S3

Factory setting 3

1. Feed the color bar signal.

1. Select L1 from the process mode LINE.

Check the Color and Tint performance.

1. Feed the monoscope pat-

tern signal.

1. Select L2 from the process mode LINE.

Check the Picture, Brightness and Sharpness per-
formance.

1. Feed the RGB signal.

1. Select L4 from the process mode LINE.

Check the Picture, Brightness, Red, Blue, Clock,
Phase, H-Position and V-Position performance.

1. Take the adjustment con-

ditions discussed for Item
11.

Make sure there is no white balance difference be-
tween the set and the standard monitor.

1. Select OFF from the process mode LINE.

Make sure the off-timer starts with 5 minutes
onscreen and the set turns itself off in 5 minutes.

1) Press SW2002 to enter the process mode.
2) Execute the S1 command on the SSS menu. (The S1 command initializes the PC board alone. Do not

execute the S2 command because otherwise the adjustment data other than the PC board will be initialized.)

3) Make sure that the program version VER.XXX on the SPECIAL menu is the latest one.

2. Adjusting the levels
2.1 Setting the oscilloscope

Set the oscilloscope range to DC 1V/div. and 5 

µ

sec/div.

2.2 Connecting the PC interface

1) Connect the specified cable between the analog output jack (signal generator) and the DUSB connector

(INPUT5 of the projector). Set the projector’s input selector to INPUT5.

2) Set the signal generator to the XGA mode (1024x768, 60 Hz, 32 tones). Adjust the output amplitude to 700

mVp-p between the black and white levels (terminated with a 75-ohm impedance).

3) Turn on the power.

2.3 Adjusting and checking the levels

1) Press SW2002 to enter the process mode.
2) Adjust the R-BRIGHT setting of Group A/D until bit dropouts start at the black level of the red signal.
3) Adjust the B-BRIGHT setting of Group A/D until bit dropouts start at the black level of the blue signal.
4) Adjust the G-BRIGHT setting of Group A/D until bit dropouts start at the black level of the green signal.

2.4 Adjusting the DTV

1) Feed the signal to the INPUT2’s RCA input terminal.
2) Set the signal generator to the 1080i 60-Hz mode with white signal. Adjust the output amplitude to 700 mVp-

p between the black and white levels.

3) Connect the specified cable between the analog output (signal generator) and the RCA connector (INPUT2

of the projector).

4) Make the G-BRIGHT setting the same as the G-BRIGHT setting of Group A/D.
5) Adjust the CB-OFFSET setting of Group DTV to 20.
6) Adjust the CR-OFFSET setting of Group DTV to 20.
7) When the CB-OFFSET and CR-OFFSET settings have been made, add 5 points to the G-BRIGHT setting for

Model XV-Z9000U and 4 points for Model XV-Z9000E.

8) Finally press SW2002 to exit from the process mode.