Sharp XV-Z12000 (serv.man33) User Manual / Operation Manual ▷ View online
Connections and Setup
-23
Optional
accessory
accessory
DVI cable
Type: AN-C3DV
Type: AN-C3DV
(3.0 m)
Desktop computer
To DVI Digital output terminal
DVI cable
(sold separately)
(sold separately)
Connecting to a Com-
puter Using a DVI
Cable (INPUT 5)
puter Using a DVI
Cable (INPUT 5)
1
Connect a DVI cable to the pro-
jector.
jector.
2
Connect the above cable to the
computer.
computer.
• Secure the connectors by tightening the
thumbscrews.
Note
• Switch the signal type to either “A. RGB”
or “D. PC RGB” depending on whether the
computer output signal is analog or digi-
tal. See page 69.
computer output signal is analog or digi-
tal. See page 69.
• Before connecting, be sure to unplug the
power cord of the projector from the AC
outlet and turn off the computer to be con-
nected. After making all connections, turn
on the projector and then the computer.
outlet and turn off the computer to be con-
nected. After making all connections, turn
on the projector and then the computer.
• Be sure that the computer is the last de-
vice to be turned on after all the connec-
tions are made.
tions are made.
To INPUT 5 terminal
XV_Z12000E_E_p15_26.p65
03.10.27, 10:41 AM
23
-24
“Plug and Play” function
■ This projector is compatible with VESA-standard DDC 1/DDC 2B. The projector and a VESA DDC
compatible computer will communicate their setting requirements, allowing for quick and easy setup.
■ Before using the “Plug and Play” function, be sure to turn on the projector first and the con-
nected computer last.
Note
• The DDC “Plug and Play” function of this projector operates only when used in conjunction with a VESA
DDC compatible computer.
Connecting the thumbscrew cables
■ Connect the thumbscrew cable making sure that it fits cor-
rectly into the terminal. Then, firmly secure the connec-
tors by tightening the screws on both sides of the plug.
tors by tightening the screws on both sides of the plug.
■ Do not remove the ferrite core attached to the RGB cable.
Ferrite core
Connecting the Projector to Other Devices
XV_Z12000E_E_p15_26.p65
03.10.27, 10:41 AM
24
Connections and Setup
-25
Controlling the
Projector Using an
RS-232C Cable
Projector Using an
RS-232C Cable
When the RS-232C terminal on the projector
is connected to a computer with an RS-232C
cable (null modem, cross type, commercially
available), the computer can be used to con-
trol the projector and check the status of the
projector. See page 84 for details.
is connected to a computer with an RS-232C
cable (null modem, cross type, commercially
available), the computer can be used to con-
trol the projector and check the status of the
projector. See page 84 for details.
1
Connect an RS-232C cable to
the projector.
the projector.
2
Connect the above cable to the
computer.
computer.
• Secure the connectors by tightening the
thumbscrews.
Note
• Do not connect or disconnect an RS-232C
cable to or from the computer while it is
on. This may damage your computer.
on. This may damage your computer.
• The RS-232C function may not operate if
your computer terminal is not correctly set
up. Refer to the operation manual of the
computer for details.
up. Refer to the operation manual of the
computer for details.
Desktop computer
To RS-232C terminal
RS-232C cable
(commercially available)
Controlling the Projector by a Computer
To RS-232C terminal
XV_Z12000E_E_p15_26.p65
03.10.27, 4:31 PM
25
Connecting the Projector to Other Devices
Using as a Wired Remote Control
Connecting the Remote
Control to the Projector
Control to the Projector
When the remote control cannot be used due
to the range or positioning of the projector (rear
projection, etc.), connect a ø3.5 mm minijack
cable (commercially available or available as
Sharp service part QCNWGA038WJPZ) from
the WIRED R/C JACK on the top of the remote
control to the WIRED REMOTE control input
terminal.
to the range or positioning of the projector (rear
projection, etc.), connect a ø3.5 mm minijack
cable (commercially available or available as
Sharp service part QCNWGA038WJPZ) from
the WIRED R/C JACK on the top of the remote
control to the WIRED REMOTE control input
terminal.
ø3.5 mm minijack cable
(commercially available or
available as Sharp service
part QCNWGA038WJPZ)
(commercially available or
available as Sharp service
part QCNWGA038WJPZ)
To WIRED R/C JACK
To WIRED REMOTE control
input terminal
input terminal
Remote control
-26
XV_Z12000E_E_p15_26.p65
03.10.27, 10:41 AM
26
Click on the first or last page to see other XV-Z12000 (serv.man33) service manuals if exist.