Sharp XV-Z12000 (serv.man33) User Manual / Operation Manual ▷ View online
Connections and Setup
-27
Setup
Foot releases
Adjustment feet
Using the Adjustment
Feet
Feet
The height of the projector can be adjusted
using the adjustment feet when the projector
is placed on an uneven surface or when the
screen is slanted.
The position of the projected image can be
made higher by adjusting the projector when
it is in a location lower than the screen.
using the adjustment feet when the projector
is placed on an uneven surface or when the
screen is slanted.
The position of the projected image can be
made higher by adjusting the projector when
it is in a location lower than the screen.
1
Press the foot releases and lift
the projector to the desired
angle.
the projector to the desired
angle.
2
Remove your hands from the
foot releases. Once the adjust-
ment feet have locked in posi-
tion, release the projector.
foot releases. Once the adjust-
ment feet have locked in posi-
tion, release the projector.
• If the screen is at an angle, the ad-
justment feet can be used to adjust the
angle of the image.
angle of the image.
Note
• The projector is adjustable up to approxi-
mately 5 degrees from the standard posi-
tion.
tion.
• When the height of the projector is ad-
justed, the image may become distorted
(keystoned), depending on the relative
positions of the projector and the screen.
See page 38 for details on the keystone
correction.
(keystoned), depending on the relative
positions of the projector and the screen.
See page 38 for details on the keystone
correction.
Info
• Do not hold the lens when lifting or lower-
ing the projector.
• When lowering the projector, be careful
not to get your finger caught in the area
between the adjustment foot and the
projector.
between the adjustment foot and the
projector.
XV_Z12000E_E_p27_32.p65
03.10.27, 10:41 AM
27
Zoom knob
Focus ring
Adjusting the Lens
The image is focused and adjusted to the
desired size using the focus ring or zoom
knob on the projector.
desired size using the focus ring or zoom
knob on the projector.
1
The focus is adjusted by rotat-
ing the focus ring.
ing the focus ring.
2
Zooming is adjusted by mov-
ing the zoom knob.
ing the zoom knob.
Setup
Zoom Knob
Focus ring
Zoom out
Zoom in
-28
XV_Z12000E_E_p27_32.p65
03.10.27, 10:41 AM
28
Connections and Setup
-29
Lens shift dial
Down
Up
Using the Lens Shift
The height of the projected image can be ad-
justed within the shift range of the lens by
rotating the lens shift dial on the top of the
projector.
justed within the shift range of the lens by
rotating the lens shift dial on the top of the
projector.
Note
• Do not turn the lens shift dial beyond the
upper limit and lower limit positions. This
may cause the projector to malfunction.
may cause the projector to malfunction.
XV_Z12000E_E_p27_32.p65
03.10.27, 10:41 AM
29
-30
90
°
90
°
Example of Standard Setup
Setting up the Screen
Position the projector perpendicular to the screen with all feet flat and level to achieve an optimal image.
Note
• The projector lens should be centred in the middle of the screen. If the horizontal line passing through the
lens centre is not perpendicular to the screen, the image will be distorted, making viewing difficult.
• For optimal image, position the screen so that it is not in direct sunlight or room light. Light falling directly on
the screen washes out the colours, making viewing difficult. Close the curtains and dim the lights when
setting up the screen in a sunny or bright room.
setting up the screen in a sunny or bright room.
• A polarizing screen cannot be used with this projector.
Standard Setup (Front Projection)
■ Place the projector at the required distance from the screen according to the desired picture size. (See
page 31.)
Screen size : 254 cm (100 inches)
Aspect ratio : 16:9
Screen size : 254 cm (100 inches)
Aspect ratio : 16:9
Side View
Top View
Audience
Setup
•
The distance from the screen to the projector
may vary depending on the size of the screen.
may vary depending on the size of the screen.
P.31
•
The default setting can be used, when placing the
projector in front of the screen. If the projected im-
age is reversed or inverted, readjust the setting to
“Front” for “PRJ Mode” in the “Options” menu.
projector in front of the screen. If the projected im-
age is reversed or inverted, readjust the setting to
“Front” for “PRJ Mode” in the “Options” menu.
P.73
•
Place the projector so that an imaginary horizontal
line that passes through the centre of the lens is
perpendicular to the screen.
line that passes through the centre of the lens is
perpendicular to the screen.
XV_Z12000E_E_p27_32.p65
03.10.27, 10:41 AM
30
Click on the first or last page to see other XV-Z12000 (serv.man33) service manuals if exist.