Sharp XV-Z10E (serv.man28) User Manual / Operation Manual ▷ View online
-31
Basic Operation
Using the Adjustment
Feet
Feet
The height of the projector can be adjusted us-
ing the adjustment feet at the front and rear of
the projector when the screen is not perpen-
dicular to the lens centre of the projector, or
when installation surface is slightly slanted.
When the screen is in a higher position than
the projector, the projection image can be made
higher by adjusting the projector.
ing the adjustment feet at the front and rear of
the projector when the screen is not perpen-
dicular to the lens centre of the projector, or
when installation surface is slightly slanted.
When the screen is in a higher position than
the projector, the projection image can be made
higher by adjusting the projector.
1
Press the HEIGHT ADJUST button.
• The front adjustment foot comes out.
2
Lift the projector to adjust its
height while pressing the HEIGHT
ADJUST button.
height while pressing the HEIGHT
ADJUST button.
• The projector is adjustable up to approxi-
mately 12 degrees (5 steps).
• When lowering the projector, it may be
difficult to move the front adjustment foot
because the installation surface is difficult
to slide. In this case, pull the projector back
slightly and adjust its height.
because the installation surface is difficult
to slide. In this case, pull the projector back
slightly and adjust its height.
3
Remove your hands from the
HEIGHT ADJUST button of the
projector after its height has been
finely adjusted.
HEIGHT ADJUST button of the
projector after its height has been
finely adjusted.
4
Use the rear adjustment foot to
make the projector level.
make the projector level.
• The projector is adjustable ±1 degree from
the standard position.
Note
• When the height of the image is being adjusted
by the adjustment feet, the image becomes dis-
torted trapezoidally. In this case, see “Correct-
ing Trapezoidal Distortion” on page 29 to cor-
rect the trapezoidal distortion.
torted trapezoidally. In this case, see “Correct-
ing Trapezoidal Distortion” on page 29 to cor-
rect the trapezoidal distortion.
Info
• Do not press the HEIGHT ADJUST button
when the front adjustment foot comes out
without firmly holding the projector.
without firmly holding the projector.
• Do not hold the lens when lifting or lowering
the projector.
• When lowering the projector, be careful not to
get your fingers caught in the area between
the adjustment foot and the projector.
the adjustment foot and the projector.
HEIGHT ADJUST
button
button
HEIGHT ADJUST button
Front adjustment
foot
foot
Rear adjustment
foot
foot
XV_Z10E_E_p26_35.p65
03.11.7, 4:15 PM
31
-32
Image Projection
In addition to the zoom function and adjustment of projection angle using the adjustment foot, it is possible
to move the lens up and down and left and right (360
to move the lens up and down and left and right (360
°
) to adjust the projection position simply by moving
the lens shift lever on the front of the projector. This is a useful function in cases such as when the screen
cannot be moved.
cannot be moved.
Adjustable range
Adjustable range
Adjustable range
Adjustable r
ange
Zooming axis
Adjustable range of
the image centre
the image centre
Image centre
Width of the projected
image
image
× (about) 30%
Height of the
projected
image
projected
image
× (about) 60%
Image centre locus
When moving upwards or downwards
Variable Lens Shift Feature
Lens shift lever
When moving in the left and right direction
Lens shift lever
Adjustable range of the lens shift lever
The adjustable range using the lens shift lever has limitations.
The image can be adjusted as shown below.
The image can be adjusted as shown below.
XV_Z10E_E_p26_35.p65
03.11.7, 4:15 PM
32
-33
Basic Operation
FREEZE button
Freezing a Moving
Image
Image
1
Press
.
• The projected image is frozen.
2
Press
again to return to the
moving image from the currently
connected device.
connected device.
Freeze Image
You can instantly freeze a moving image with
the remote control.
the remote control.
Adjusting the Projected
Image Position
Image Position
Adjust the projected image position
using the lens shift lever.
using the lens shift lever.
Info
• When using the projector (during projection),
be sure not to subject the projector to any
impact. If the projector is subjected to impact,
the projection image may deviate from the
adjusted position.
impact. If the projector is subjected to impact,
the projection image may deviate from the
adjusted position.
• When transporting or carrying the projector,
attach the lens shipping block and the lens
cap to the projector.
cap to the projector.
• When the angle is being adjusted using the
adjustment foot, deviation of the projected
image arising when carrying out lens shift in
the lateral direction cannot be corrected by
the Keystone Correction.
image arising when carrying out lens shift in
the lateral direction cannot be corrected by
the Keystone Correction.
XV_Z10E_E_p26_35.p65
03.11.7, 4:15 PM
33
-34
Selecting the Picture Display Mode
This function allows you to modify or customise the picture display mode to enhance
the input image. Depending on the input signal, you can choose “STRETCH”, “SIDE
BAR” or “CINEMA ZOOM” image.
the input image. Depending on the input signal, you can choose “STRETCH”, “SIDE
BAR” or “CINEMA ZOOM” image.
Switching the Picture
Display Using Different
Input Signals
Display Using Different
Input Signals
Press
.
• Pressing
changes the picture display mode
as shown on page 35.
• To return to the standard image (“STRETCH”),
press
while “RESIZE” is displayed on the
screen.
• You can also change the picture display mode
by pressing
on the projector.
RESIZE button
UNDO
button
button
RESIZE button
UNDO button
XV_Z10E_E_p26_35.p65
03.11.7, 4:16 PM
34
Click on the first or last page to see other XV-Z10E (serv.man28) service manuals if exist.