Sharp XV-Z10E (serv.man28) User Manual / Operation Manual ▷ View online
-27
Basic Operation
"On-screen Display of INPUT Mode (Example)
Using RGB
Using
Component
Component
INPUT 1 mode
INPUT 3 mode
Using Video
Using Video
INPUT 2 mode
Using S-Video
Using S-Video
➝
➝
➝
INPUT buttons
Switching the INPUT
Mode
Mode
Select the appropriate input mode for the con-
nected equipment.
nected equipment.
Press
,
or
on the remote
control to select the INPUT mode.
••••• When pressing
on the projector, input mode
switches in order of
INPUT 1
INPUT 2
INPUT 3
.
Note
• When no signal is received, “NO SIGNAL” will
be displayed. When a signal that the projec-
tor is not preset to receive is received, “NOT
REG.” will be displayed.
tor is not preset to receive is received, “NOT
REG.” will be displayed.
• The INPUT mode is not displayed when “OSD
Display” of the “Options” menu is set to
“
“
” (OFF). (See page 47.)
About the INPUT mode
INPUT 1
(Compo-
nent/RGB)
(Compo-
nent/RGB)
INPUT 2
(S-Video)
(S-Video)
INPUT 3
(Video)
(Video)
Adjusting the Volume
Press
or
on the remote con-
trol to adjust the volume.
Note
• Pressing
will lower the volume.
Pressing
will raise the volume.
• On the projector, the volume can be adjusted
by pressing
or
.
Volume
buttons
buttons
"On-screen Display
Volume buttons
Used for projecting images from equip-
ment that sends component signals or
RGB signals connected to the INPUT 1
terminal.
ment that sends component signals or
RGB signals connected to the INPUT 1
terminal.
Used for projecting images from
equipment connected to the INPUT 2
terminal.
equipment connected to the INPUT 2
terminal.
Used for projecting images from
equipment connected to the INPUT 3
terminal.
equipment connected to the INPUT 3
terminal.
XV_Z10E_E_p26_35.p65
03.11.7, 4:15 PM
27
-28
STANDBY
button
button
"On-screen Display
Image Projection
Turning off the Sound
Temporarily
Temporarily
Press
on the remote control to tem-
porarily turn off the sound.
Note
• Pressing
again will turn the sound back
on.
Turning the Power off
(Putting
the Projector into the Standby Mode)
1
Press
on the projector or
on the remote control, then
press that button again while the
confirmation message is dis-
played, to put the projector into
the standby mode.
confirmation message is dis-
played, to put the projector into
the standby mode.
Note
• If you accidentally pressed
or
and do not want to put the projec-
tor into the standby mode, wait until the
confirmation message disappears.
confirmation message disappears.
2
Unplug the power cord from the wall
outlet after the cooling fan stops.
outlet after the cooling fan stops.
Info
• Do not unplug the power cord during pro-
jection or cooling fan operation. The cool-
ing fan in this projector continues to run
for about 90 seconds after the projector en-
ters the standby mode. This can cause
damage due to rise in internal temperature,
as the cooling fan also stops.
ing fan in this projector continues to run
for about 90 seconds after the projector en-
ters the standby mode. This can cause
damage due to rise in internal temperature,
as the cooling fan also stops.
MUTE button
"On-screen Display
XV_Z10E_E_p26_35.p65
03.11.7, 4:15 PM
28
-29
Basic Operation
'
,
"
,
\
,
|
buttons
KEYSTONE
button
button
UNDO
button
button
'
,
"
,
\
,
|
buttons
UNDO button
Correcting Trapezoidal
Distortion
Distortion
When the image is projected either from the top or
from the bottom towards the screen at an angle,
the image becomes distorted trapezoidally.
The function for correcting trapezoidal distortion
is called Keystone Correction.
from the bottom towards the screen at an angle,
the image becomes distorted trapezoidally.
The function for correcting trapezoidal distortion
is called Keystone Correction.
Note
• The Keystone Correction can be adjusted up
to an angle of approximately
±30 degrees and
the screen can also be set up to an angle of
approximately
approximately
±30 degrees (when the resize
mode is set to “STRETCH” for the video sig-
nal input or “SIDE BAR” for the computer sig-
nal input).
nal input or “SIDE BAR” for the computer sig-
nal input).
• The Keystone Correction cannot be adjusted
in the lateral direction.
• For details about the setup, see pages 7 and
16.
1
Press
to enter the Keystone
Correction mode.
• The on-screen display of the Keystone
Correction mode will appear.
2
Press ', ", \ and | to adjust
the Keystone Correction.
• You can also adjust the Keystone Correc-
tion using the
,
,
and
but-
tons on the projector.
Note
• Press
to return to the default set-
ting.
• Straight lines or the edges of images
may appear jagged while adjusting the
image.
image.
• When correcting trapezoidal distortion,
the aspect ratio of the image will change
slightly .
slightly .
3
Press
.
• The on-screen display of the Keystone
Correction mode will disappear.
"On-screen display (Keystone Correction mode)
Compresses
lower side.
lower side.
Compresses
upper side.
upper side.
XV_Z10E_E_p26_35.p65
03.11.7, 4:15 PM
29
-30
Image Projection
Adjusting the Lens
The image is focused and adjusted to the de-
sired size using the focus ring or zoom knob
on the projector.
sired size using the focus ring or zoom knob
on the projector.
1
Adjust the focus by rotating the
focus ring.
focus ring.
2
Adjust zooming by moving the
zoom knob.
zoom knob.
Focus ring
Zoom knob
Zoom in
Zoom out
XV_Z10E_E_p26_35.p65
03.11.7, 4:15 PM
30
Click on the first or last page to see other XV-Z10E (serv.man28) service manuals if exist.