Sharp XV-Z10000 Handy Guide ▷ View online
Lamp Replacement Procedure
Version 1.3
Issue 04/2006
Issue 04/2006
13
SHARP ELECTRONICS (UK) LTD
PROJECTOR TECHNICAL SUPPORT
TECHNICAL SERVICES GROUP
Resetting the Lamp Timer
Reset the lamp timer after replacing the lamp.
1.
Connect the power cord.
•
Plug the power cord into the AC socket of the projector.
2.
Reset the lamp timer.
•
While holding the “ENTER”, “DOWN” and “RIGHT”,
press the “ON” key.
press the “ON” key.
•
“LAMP 0000H” is displayed, indicating that the lamp
timer is reset.
timer is reset.
Note
•
Make sure to reset the lamp timer only when replacing
the lamp. If you reset the lamp timer and continue to
use the same lamp, this may cause the lamp to
become damaged or explode.
the lamp. If you reset the lamp timer and continue to
use the same lamp, this may cause the lamp to
become damaged or explode.
•
You need to reset the lamp timer every time you
replace the lamp and confirm it is reset on the “Lamp
Timer” menu.
replace the lamp and confirm it is reset on the “Lamp
Timer” menu.
Maintenance Procedure
Version 1.3
Issue 04/2006
Issue 04/2006
14
SHARP ELECTRONICS (UK) LTD
PROJECTOR TECHNICAL SUPPORT
TECHNICAL SERVICES GROUP
Cleaning the projector
•
Be sure to unplug the power cord before cleaning the projector.
•
The cabinet as well as the operation panel is made of plastic. Avoid using benzene or
thinner, as these can damage the finish on the cabinet.
thinner, as these can damage the finish on the cabinet.
•
Do not use volatile agents such as insecticides on the projector.
Do not attach rubber or plastic items on the projector for long time.
The effects of some of the agents in the plastic may cause damage to the quality or finish
of the projector.
Do not attach rubber or plastic items on the projector for long time.
The effects of some of the agents in the plastic may cause damage to the quality or finish
of the projector.
•
Wipe off dirt gently with a soft flannel cloth.
•
When the dirt is hard to remove, soak a cloth in a neutral detergent diluted with water,
wring the cloth well and then wipe the projector.
Strong cleaning detergents may discolour, warp or damage the coating on the projector.
Make sure to test on a small, inconspicuous area on the projector before using.
wring the cloth well and then wipe the projector.
Strong cleaning detergents may discolour, warp or damage the coating on the projector.
Make sure to test on a small, inconspicuous area on the projector before using.
Cleaning the lens
•
Use a commercially available blower or lens cleaning paper (for glasses and camera
lenses) for cleaning the lens. Do not use any liquid type-cleaning agents, as they may
wear off the coating film on the surface of the lens.
lenses) for cleaning the lens. Do not use any liquid type-cleaning agents, as they may
wear off the coating film on the surface of the lens.
•
As the surface of the lens can easily get damaged, be sure not to scrape or hit the lens.
Cleaning the exhaust and intake vents
•
Use a vacuum cleaner to clean dust from the
exhaust vent and the intake vent.
exhaust vent and the intake vent.
Options
Version 1.3
Issue 04/2006
Issue 04/2006
15
SHARP ELECTRONICS (UK) LTD
PROJECTOR TECHNICAL SUPPORT
TECHNICAL SERVICES GROUP
UK Options
Sales Code
Description
AN-W9Z
Wide Angle Lens
AN-NV6T
Ceiling Mount Bracket
AN-TK201
High Ceiling Installation
AN-TK202
Standard Ceiling Installation
AN-NV6T
AN-TK202
AN-TK201
Setting up the Screen
Position the projector perpendicular to the screen with all feet flat and level to achieve an
optimal image.
optimal image.
Note
•
The projector lens should be centred in the middle of the screen. If the horizontal line
passing through the lens centre is not perpendicular to the screen, the image will be
distorted, making viewing difficult.
passing through the lens centre is not perpendicular to the screen, the image will be
distorted, making viewing difficult.
•
For optimal image, position the screen so that it is not in direct sunlight or room light.
Light falling directly on the screen washes out the colours, making viewing difficult. Close
the curtains and dim the lights when setting up the screen in a sunny or bright room.
Light falling directly on the screen washes out the colours, making viewing difficult. Close
the curtains and dim the lights when setting up the screen in a sunny or bright room.
•
A polarising screen cannot be used with this projector.
Options
Version 1.3
Issue 04/2006
Issue 04/2006
16
SHARP ELECTRONICS (UK) LTD
PROJECTOR TECHNICAL SUPPORT
TECHNICAL SERVICES GROUP
Upper and Lower Lens Shift Position
•
This projector is equipped with a lens shift function that lets you adjust the projection
height.
height.
•
Adjust it to match the set-up configuration.
•
The screen can be moved maximum the length of one screen vertically using the lens
shift.
shift.
Click on the first or last page to see other XV-Z10000 service manuals if exist.