Sharp XV-Z10000 (serv.man28) User Manual / Operation Manual ▷ View online
-30
Projection from behind the screen
■ Place a translucent screen between the projector and the au-
dience.
■ Reverse the image by setting “Rear” for “PRJ Mode” in the
“Options” menu. See
page 69 for use of
this function.
page 69 for use of
this function.
Projection using a mirror
■ Place a mirror (normal flat type) in front of the lens.
■ Reverse the image by setting “Rear” for “PRJ Mode” in the
“Options” menu,
when the mirror is
placed on the audi-
ence side. See page
69 for use of this
function.
when the mirror is
placed on the audi-
ence side. See page
69 for use of this
function.
Info
•
When using a mirror, be sure to carefully position both the pro-
jector and the mirror so the light does not shine into the eyes of
the audience.
jector and the mirror so the light does not shine into the eyes of
the audience.
Ceiling-mount setup
■ It is recommended that you use the optional Sharp ceiling-mount
bracket for this installation.
■ Before mounting the projector, contact your nearest Sharp
Authorised Projector Dealer or Service Centre to obtain the
recommended ceiling-mount bracket (sold separately). (AN-
TK202 ceiling-mount bracket, AN-TK201 extension tube, AN-
NV6T ceiling adaptors for AN-TK202 or AN-TK201.)
recommended ceiling-mount bracket (sold separately). (AN-
TK202 ceiling-mount bracket, AN-TK201 extension tube, AN-
NV6T ceiling adaptors for AN-TK202 or AN-TK201.)
■ Be sure to adjust the position of the projector to match the
distance (z) from the lens centre position (see page 29) to the
lower edge of the image,
when mounting the projec-
tor on the ceiling.
lower edge of the image,
when mounting the projec-
tor on the ceiling.
■ Invert the image by setting
“Ceiling + Front” for “PRJ
Mode” in the “Options”
menu. See page 69 for use
of this function.
Mode” in the “Options”
menu. See page 69 for use
of this function.
When using the default setting.
▼On-screen Display
Projecting a Reversed/Inverted Image
The image is reversed.
When using the default setting.
▼On-screen Display
The image is reversed.
When using the default setting.
▼On-screen Display
Setup
The image is inverted.
Basic Operation
Basic Operation
Image Projection
Basic Procedure
Connect the required external equipment to
the projector before operating the following
procedures.
the projector before operating the following
procedures.
Info
•
The language preset at the factory is English.
If you want to change the on-screen display
to another language, reset the language ac-
cording to the procedure on page 34.
If you want to change the on-screen display
to another language, reset the language ac-
cording to the procedure on page 34.
1
Plug the power cord into the
wall outlet.
•
The power indicator illuminates red, and
the projector enters standby mode.
the projector enters standby mode.
2
Press
ON
on the remote con-
trol or
on the projector.
•
The power indicator illuminates blue.
After the lamp replacement indicator il-
luminates, the projector is ready to start
operation.
After the lamp replacement indicator il-
luminates, the projector is ready to start
operation.
Note
•
The lamp replacement indicator il-
luminates, indicating the status of the
lamp.
luminates, indicating the status of the
lamp.
Blue: The lamp is ready.
Blue blinking: The lamp is
Blue blinking: The lamp is
warming up.
Red: The lamp should be replaced.
•
If the power is turned off and imme-
diately switched on again, the lamp
replacement indicator may take time
to illuminate.
diately switched on again, the lamp
replacement indicator may take time
to illuminate.
•
When controlling the projector using
RS-232C commands from a com-
puter, wait for at least 30 seconds
after the power has been turned on,
and then transmit the commands.
RS-232C commands from a com-
puter, wait for at least 30 seconds
after the power has been turned on,
and then transmit the commands.
-32
INPUT
button
button
Power (ON)
button
button
Power (OFF)
button
button
MENU button
", ',\, | buttons
ENTER
button
button
Power (ON)
button
button
INPUT
buttons
buttons
', ", \, |
buttons
buttons
MENU button
ENTER
button
Power (OFF)
button
Lamp replacement
indicator
indicator
Power indicator
Basic Operation
-33
3
Press
,
,
,
or
on the remote control or
on
the projector to select the IN-
PUT mode.
PUT mode.
•
After pressing
once on the projector,
use
to select the desired input mode.
Note
•
When no signal is received, “NO
SIGNAL” will be displayed. When a
signal that the projector is not pre-
set to receive is received, “NOT
REG.” will be displayed.
SIGNAL” will be displayed. When a
signal that the projector is not pre-
set to receive is received, “NOT
REG.” will be displayed.
•
The INPUT mode is not displayed
when “OSD display” is set to “Level
A” or “Level B”. (See page 64.)
when “OSD display” is set to “Level
A” or “Level B”. (See page 64.)
About the INPUT modes
"On-screen Display (Example)
Using RGB*
Using
Component
Component
INPUT 2 mode
Using
Component
Component
INPUT 1 mode
INPUT 3 mode
INPUT 4 mode
Using RGB*
➝
➝➝
➝
INPUT 5 mode
➝
* Input the RGB signal of the DTV, not
the computer.
Using S-Video
Using Video
Using Analog
RGB
RGB
The display varies accord-
ing to the “Signal Type” with
the INPUT 5. The diagram
shown above is the ex-
ample of having selected
“Analog RGB”.
ing to the “Signal Type” with
the INPUT 5. The diagram
shown above is the ex-
ample of having selected
“Analog RGB”.
Used for projecting images
from equipment that sends
component signals or RGB
signals connected to the
INPUT 1 or 2 terminals.
from equipment that sends
component signals or RGB
signals connected to the
INPUT 1 or 2 terminals.
Used for projecting im-
ages from equipment con-
nected to the S-VIDEO in-
put terminal.
ages from equipment con-
nected to the S-VIDEO in-
put terminal.
Used for projecting im-
ages from equipment
connected to the VIDEO
input terminal.
Used for projecting im-
ages from equipment
connected to the DVI in-
put terminal.
ages from equipment
connected to the VIDEO
input terminal.
Used for projecting im-
ages from equipment
connected to the DVI in-
put terminal.
INPUT 1
INPUT 2
(Compo-
nent/RGB*)
INPUT 2
(Compo-
nent/RGB*)
INPUT 3
(S-Video)
(S-Video)
INPUT 4
(Video)
(Video)
INPUT 5
(Digital PC
RGB/
Digital PC
Component/
Digital Video
RGB/Digital
Video
Component/
Analog RGB/
Analog
Component)
(Digital PC
RGB/
Digital PC
Component/
Digital Video
RGB/Digital
Video
Component/
Analog RGB/
Analog
Component)
Click on the first or last page to see other XV-Z10000 (serv.man28) service manuals if exist.