Sharp XG-P25XE (serv.man38) User Manual / Operation Manual ▷ View online
E-50
Basic Operation
These functions allow you to reduce the power consumption. See page
38
for the procedure details.
Selecting the Economy Mode
Power Save Function
Function to control the quantity of projected light. Select “
(Low Power Mode)” or “
(Standard Mode)” to
decrease or increase brightness, fan noise and power consumption.
Quantity of light is 85 %.
Power consumption is about 350 W.
Power consumption is about 350 W.
Quantity of light is 100 %.
Power consumption is 380 W.
Power consumption is 380 W.
• “Power Save” mode is factory preset to “
(Standard Mode)”.
• Even when selecting “
(Low Power Mode)” in “Power Save” mode, fan noise may increase if internal temperature rises
enough to activate the cooling function.
Monitor Out/RS-232C Off Function
This projector consumes power when using a monitor connected to the OUTPUT port for INPUT 1, 2 and a
computer connected to the RS-232C port. When not using these ports, “MNTR Out/RS232C” can be set to “
computer connected to the RS-232C port. When not using these ports, “MNTR Out/RS232C” can be set to “
” to
reduce standby power consumption.
Standby power for Monitor Out/RS-232C
connection turned off.
connection turned off.
Monitor Out/RS-232C on
CAUTION
• Set “MNTR Out/RS232C” to “
” when using the Sharp Advanced Presentation Software (supplied).
• “MNTR Out/RS232C” is factory preset to “
”, and “Auto Power Off” is factory preset to “
”.
Automatic Power Shutoff Function
When no input signal is detected for more than 15 minutes, the projector will automatically shut off. The on-screen
message, “Power OFF in 5 min.” will appear five minutes before the power is automatically turned off.
message, “Power OFF in 5 min.” will appear five minutes before the power is automatically turned off.
Power automatically shuts off after about 15
minutes of no signal input.
minutes of no signal input.
Automatic Power Shutoff disabled.
E-51
Basic Operation
Confirming the Lamp Usage Time
This function allows you to check the accumulated lamp usage time. See page
38
for the procedure
details.
• It is recommended that the lamp be replaced after approximately 1,400 cumulative hours of use. See pages
64
and
65
for
lamp replacement.
Reversing/Inverting Projected Images
This projector is equipped with a reverse/invert image function which allows you to reverse or invert the
projected image for various applications. See page
projected image for various applications. See page
38
for the procedure details.
Description
Normal image
Inverted image
Reversed image
Reversed and inverted image
Selected item
Front
Ceiling
ⳭFront
Rear
Ceiling
ⳭRear
• This function is used for the reversed image and ceiling-mount setups. See page
30
for these setups.
E-52
Basic Operation
Setting the Stacking Mode
You can double the brightness of an image by stacking two projectors and projecting the same picture
simultaneously. (Stack Projection)
Connect two projectors by using the RS-232C cable. Then assign one as the master and the other as
the slave. In this way, you can control two projectors with one remote control. See page
simultaneously. (Stack Projection)
Connect two projectors by using the RS-232C cable. Then assign one as the master and the other as
the slave. In this way, you can control two projectors with one remote control. See page
38
for the
procedure details.
• When operating the master projector with the remote control, actuating signals are transmitted to the slave projector through
RS-232C, which then responds in concert with the master. The buttons below can control both the master and the slave at
one time.
POWER ON, POWER OFF, BLACK SCREEN, INPUT (1, 2, 3, 4 or 5)
one time.
POWER ON, POWER OFF, BLACK SCREEN, INPUT (1, 2, 3, 4 or 5)
• The slave projector cannot be controlled directly with the remote control.
• Even after setting up for stack projection, you can still control each projector by one of the methods below.
• Even after setting up for stack projection, you can still control each projector by one of the methods below.
(a) Use the operation buttons on the projector.
(b) Connect the remote control to the projector with a cable.
(b) Connect the remote control to the projector with a cable.
• For details on intended purpose, see pages
59
to
62
.
Locking the Operation Buttons on the Projector
This function can be used to lock the use of certain operation buttons on the projector. The user can still
operate the projector fully with the remote control. See page
operate the projector fully with the remote control. See page
38
for the procedure details.
Description
All operation buttons are functional.
Only Input/Volume/Mute functions on the
projector are available.
All operation buttons on the projector are
unavailable.
unavailable.
Selected item
Normal
Level A
Level B
• To cancel the Keylock Level, perform the above procedure using the remote control.
• See page
• See page
55
for details using the password function.
E-53
Basic Operation
Deselecting Inputs
This function allows you to deselect unwanted signal input. See page
38
for the procedure details.
• When stack projecting, multi-screen projecting and so on, this function can be used to cancel the RS-232C control.
• Up to two input signals can be blocked for both Input 1, 2, 3 or Input 4, 5.
• For details on intended purpose, see pages
• Up to two input signals can be blocked for both Input 1, 2, 3 or Input 4, 5.
• For details on intended purpose, see pages
59
to
62
.
Selecting the Transmission Speed (RS-232C)
This menu allows you to adjust the transmission speed of the RS-232C connection by selecting the
baud rate. See page
baud rate. See page
38
for the procedure details.
• Make sure that both the projector and computer are set for the same baud rate. Refer to the computer’s operation manual
for instructions for setting the baud rate.
Click on the first or last page to see other XG-P25XE (serv.man38) service manuals if exist.