DOWNLOAD Sharp XG-P25XE (serv.man38) Service Manual ↓ Size: 9.62 MB | Pages: 82 in PDF or view online for FREE

Press the tab and lift open the
battery cover in the direction of
the arrow.

Insert the tabs on the end of
the battery cover into their
slots and press the cover into
position.

Insert two R-6 batteries (“AA”
size, UM/SUM-3, HP-7 or
similar), making sure the
polarities match the 

ⴐ and ⴑ

marks inside the battery
compartment.

• Insert the batteries making sure the polarities correctly match the 

Ⳮ and ⳮ marks inside the battery compartment.

• Batteries of different types have different properties, therefore do not mix batteries of different types.
• Do not mix new and old batteries.

This may shorten the life of new batteries of may cause old batteries to leak.

• Remove the batteries from the remote control once they have run out, as leaving them can cause them to leak.

Battery fluid from leaked batteries is harmful to your skin, therefore be sure to first wipe them and then remove them using a cloth.

• The batteries included with this projector may be used up over a short period, depending on how they are kept. Be sure to replace them as

soon as possible with new batteries.

• Remove the batteries from the remote control if you will not be using the remote control for a long time.

The remote control can be used to control the projector within the ranges
shown in the illustration.

• The signal from the remote control can be reflected off a screen for easy operation.

However, the effective distance of the signal may differ due to the screen material.

When using the remote control:
• Be sure not to drop, expose to moisture or high temperature.
• The remote control may malfunction under a fluorescent lamp. Under that

circumstance, move the projector away from the fluorescent lamp.

45˚

23

⬘ (7 m)

30˚

30˚

45˚

30˚

When the remote control cannot be used due to the range or positioning of the projector (rear projection, etc.),
connect a ø3.5 mm minijack cable (commercially available) from the wired RC jack on the bottom of the remote
control to the WIRED REMOTE control input terminal on the rear of the projector.

ø3.5 mm minijack cable
(commercially available)

Battery cover

Battery

compartment

Battery

cover

Remote control
RRMCGA048WJSA

Two R-6 batteries
(“AA” size, UM/SUM-3,
HP-7 or similar)

Power cord

For U.S., Canada etc.
(11

⬘ 10⬙, 3.6m)

QACCDA010WJPZ

For Europe, except U.K.
(6

⬘, 1.8m)

QACCV4002CEZZ

For U.K., Hong Kong
and Singapore
(6

⬘, 1.8m)

QACCBA012WJPZ

For Australia, New
Zealand and Oceania
(6

⬘, 1.8m)

QACCL3022CEZZ

(1)

(2)

(3)

(4)

• Depending on the region, projectors only ship with one power cord (See above). Use the power cord that corresponds to the wall outlet

in your country.

Computer audio cable
(ø3.5 mm stereo minijack cable)
(9

⬘ 10⬙, 3m)

QCNWGA013WJPZ

RGB cable
(9

⬘ 10⬙, 3m)

QCNWGA012WJPZ

Three BNC-RCA adaptors
QPLGJ0107GEZZ

Lens cap
(attached)
PCAPH1056CESA

Extra air filter
PFILD0080CEZZ

Sharp Advanced Presentation
Software installation guide
TINS-A139WJZZ

ID number seal
TLABZ0781CEZZ

LCD projector operation manual
TINS-A133WJZZ

Quick reference guides

Projector Manual and Technical
Reference CD-ROM
UDSKAA004WJZZ

Sharp Advanced Presentation
Software CD-ROM
UDSKAA005WJZZ

DVI cable (9

⬘ 10⬙ (3.0 m))

3 RCA to 15-pin D-sub cable (9

⬘ 10⬙ (3.0 m))

Computer RGB cable (32

⬘ 10⬙ (10.0 m))

5 BNC to 15-pin D-sub cable (9

⬘ 10⬙ (3.0 m))

RS-232C serial control cable (32

⬘ 10⬙ (10.0 m))

DVI to 15-pin D-sub adaptor (7.9

⬙ (20 cm))

AN-C3DV
AN-C3CP
AN-C10BM
(for IBM-PC, NEC PC-9821 and PC-98NX series)
AN-C10MC
(for Macintosh series)
AN-C10PC
(for NEC PC-98 series (Except NEC PC-9821 and PC-98NX series)
AN-C3BN
AN-C10RS
AN-A1DV

• All cables may not be available in all regions. Please check with your nearest Sharp Authorized LCD Projector Dealer or Service Center.

Plug the supplied power cord into the AC socket on the rear of the projector.

Power cord

• If the bottom filter cover is not securely installed, the POWER

indicator blinks.

You can connect your projector to a computer for projection of full color computer images.

Connect one end of the supplied RGB cable to the INPUT 1 port on the projector.

Connect the other end to the monitor output port on the computer. Secure the connectors by tightening the
thumb screws.

To use the built-in audio system, connect one end of the supplied computer audio cable to the AUDIO INPUT 1
terminal on the projector.

Connect the other end to the audio output terminal on the computer.

• Before connecting, be sure to turn both the projector and the computer off. After making all connections, turn the projector on first. The

computer should always be turned on last.

• Please read the computer’s operation manual carefully before making connections.
• Refer to page 

 “Compatibility Chart” for a list of computer signals compatible with the projector. Use with computer signals other than

those listed may cause some of the functions not to work.

• A ø3.5 mm stereo minijack to stereo RCA audio cable adaptor may be necessary.

When connecting this projector to a computer, select “RGB” for “Signal Type” on the GUI menu. (See page 

• A Macintosh adaptor may be required for use with some Macintosh computers. Contact your nearest Sharp Authorized LCD Projector

Dealer or Service Center.

• AUDIO INPUT 1 can be used to input audio corresponding to the INPUT 1.

Computer audio cable

RGB cable

POWER indicator

Make the necessary connections before
proceeding. Connect the power cord to a wall
outlet.
The POWER indicator lights up red and the
projector enters standby mode.

• This projector uses a 5 BNC computer input to prevent deterioration of image quality.
• Connect the R (P

R

), G/G sync (Y), B (P

B

), HD/C sync and VD cables (sold separately) to the correct input

terminals on the projector and an RGB switcher (sold separately) connected to the computer, or connect a 5
BNC cable (sold separately) directly from the input terminals on the projector to the computer.

5 BNC cable

(sold separately)

Connect each BNC connector of a 5 BNC cable to the corresponding INPUT 2 terminals on the projector.

Connect the other end of the 5 BNC cable to the corresponding BNC terminals on the external RGB switcher.
Connect the RGB switcher to the computer using a RGB cable.

To use the built-in audio system, connect one end of the supplied computer audio cable to the AUDIO INPUT 2/
3 terminal on the projector.

Connect the other end to the audio output terminal on the computer or external audio system.

• A ø3.5 mm stereo minijack to stereo RCA audio cable adaptor may be necessary.

When connecting the projector to a compatible computer other than a PC (VGA/SVGA/XGA/SXGA/UXGA) or Macintosh (i.e.
Workstation), a separate cable may be needed. Please contact your dealer for more information.

When connecting this projector to a computer, select “RGB” for “Signal Type” on the GUI menu. (See page 

• Connecting computers other than the recommended types may result in damage to the projector, the computer, or both.
• AUDIO INPUT 2/3 can be used to input audio corresponding to the INPUT 2/3.

Computer audio cable

To audio output
terminal

To R (P

R

), G/G sync (Y), B (P

B

),

HD/C sync and VD output terminals

 To RGB switcher

RGB switcher
(sold separately)

RGB cable

• This projector is compatible with VESA-standard DDC 1/DDC 2B. The projector and a VESA DDC compatible

computer will communicate their setting requirements, allowing for quick and easy setup.

• Before using the “Plug and Play” function, be sure to turn on the projector first and the connected computer last.

• The DDC “Plug and Play” function of this projector operates only when used in conjunction with a VESA DDC compatible computer.