DOWNLOAD Sharp XG-NV7XE (serv.man3) Service Manual ↓ Size: 1.04 MB | Pages: 43 in PDF or view online for FREE

1. Feed the PAL color bar sig-

nal.
Group : VIDEO 1
Subject : P-COLOR

2. Connect the oscilloscope to

TP804.

»

Using the control switches or the remote controller
buttons, adjust the difference between the 100%
white portion and the red portion to 0.28 ±0.02 Vp-p.

1. Feed the SECAM color bar

signal.
Group : VIDEO 1
Subject : S-COLOR

2. Connect the oscilloscope to

TP804.

»

Using the control switches or the remote controller
buttons, adjust the data to have a level difference
of 0.28 ±0.02 Vp-p between the 100% white
portion and the red portion.

1. Feed the NTSC mono-

scope pattern signal
Group : VIDEO 2
Subject : R OFF-SET

B OFF-SET

»

Using the control switches or the remote controller
buttons, adjust so that the entire screen looks
evenly colorless.

100% White Red

100% White Red

1. Feed the color bar signal of

the 480I component signal to
the D-SUB input terminal.

2. Select the following subject.

Group : DVD
Subject : CONTRAST

3. Connect the oscilloscope to

TP805.

»

Using the control switch or the button on the
remote controller, adjust the amplitude between
the black and 100% white to 2.1 ±0.02 Vp-p.

100% White

2.1

±

0.02Vp-p

1. Feed the color bar signal of

the 480I component signal
to the D-SUB input termi-
nals. Feed the sync signal
only for the Y signal.

2. Select the following subject.

Group : DVD
Subject : TINT

3. Connect the oscilloscope to

TP807.

»

Using the control switch or the button on the
remote controller, adjust the B-Y waveform to form
a straight slope.

1. Receive the color bar sig-

nal.

»

In the process mode and select L1. Check the color
and tint.

»

In the process mode nad select L3. Check the bass,
treble and balance.

1. Receive the monoscope

pattern signal.

»

In the process mode and select L2. Check the pic-
ture, brightness and sharpness.

1. Feed the color bar signal of

the 480I component signal to
the D-SUB input terminal.

2. Select the following subject.

 Group : DVD
Subject : COLOR

3. Connect the oscilloscope to

TP804.

»

Adjust the level difference between the 100% white
and red portions to 0.1 ±0.02 Vp-p.

100% White Red

1. Receive the RGB1 signal.

»

In the process mode and select L4. Check the pic-
ture, brightness, red, blue, clock, phase, horizontal
position, and vertical position.

»

In the process mode and select OFF. Make sure that
the off-timer starts with “5” (minutes), counts down
each minute in 1 second, and turns off the set at “0”.

1. Make the following settings:

RGB2 mode and XGA spe-
cific for panel link. Enter the
32-step gradation pattern.

»

Make sure that the gradation pattern is not corrupted
and that the black portion is not too sinking.

S4

“Factory setting 4”

Remote controller
setting

Process
adjustment

»

Make the following settings.

»

Make sure the IrDA signal can be received.

»

Make sure the keystone correction functions well.

1. Heat the thermistor using a

dryer.

»

Make sure the “TEMP” is displayed.

1. Receive the PHASE check

pattern signal.

»

Call the VGA/S-VGA/XGA/SXGA/UXGA mode and
make sure that the clock, phase, horizontal and
vertical positions can be automatically adjusted.

1. Receive the PHASE check

pattern signal.

»

In the VGA/S-VGA/XGA/SXGA modes, make sure
that the H-POS and V-POS can be automatically
adjusted.

1) Press the S5001 switch to call the process mode.

2) Pick up the item S1 on the SSS menu. (The S1 is used to initialize the PC interface alone. Do not select the

item S2 because otherwise the other data than the PC interface will be initialized.)

1

Oscilloscope setting

Set the range to DC 1 V/div. and 5 µ s/div.

2

Input signal

Feed the XGA 1024x768, 60Hz gradation waveform signal and the DTV (720P for example) signal.

3

Level adjustment and checking

1) Press the S5001 switch to call the process mode.

2) Adjust R750 so that the voltage at test point TL119 be 2.6 ±0.05V.

3) Set the BRIGHT data on the A/D menu to 125.

4) Adjust the R-BRIGHT data on the A/D menu so that the voltage at TP3 be 1.7V.

5) Adjust the G-BRIGHT data on the A/D menu so that the voltage at TP2 be 1.7V.

6) Adjust the B-BRIGHT data on the A/D menu so that the voltage at TP1 be 1.7V.

7) Make sure that the GAIN data on the A/D menu is 155.

8) Connect the synchroscope to TP3. Adjust the R-D data on the A/D menu so that the signal’s white peak be

3.6V. (Be also sure that the white and black portions of the gradation are not corrupted.)

9) Connect the synchroscope to TP1. Adjust the B-D data on the A/D menu so that the signal’s white peak be

3.6V. (Be also sure that the white and black portions of the gradation are not corrupted.)

10) Connect the synchroscope to TP2. Adjust the G-D data on the A/D menu so that the signal’s white peak

be 3.6V. (Be also sure that the white and black portions of the gradation are not corrupted.)

11) Feed the DTV signal instead. Enter only the Y component, not the Pb and Pr components.

12) Adjust the R-BRIGHT data on the DTV menu so that the voltage at TP3 be 2.65V.

13) Adjust the B-BRIGHT data on the DTV menu so that the voltage at TP1 be 2.65V.

14) Press the S5001 switch to exit the process mode.