Sharp XG-MB67X (serv.man17) User Manual / Operation Manual ▷ View online
-17
Controlling the Projector via LAN
Setting Error Items and
Destination Addresses to
which E-mail is to be Sent
when an Error Occurs
Destination Addresses to
which E-mail is to be Sent
when an Error Occurs
(Mail – Recipient Settings)
On this screen, you can input e-mail destina-
tions to which error notification (error items)
e-mails are sent.
tions to which error notification (error items)
e-mails are sent.
Note
• E-mail Address can be up to 64 characters.
• You can input the characters below :
• You can input the characters below :
a-z, A-Z, 0-9, !, #, $, %, &, *, +, -, /, =, ?, ^, {, |,
}, ~, _, ’, ., @, `
(You can input “@” only one time.)
}, ~, _, ’, ., @, `
(You can input “@” only one time.)
• For details about error items, refer to the
projector’s operation manual.
Description
Set addresses to which error
notification e-mail is sent. You
can set up to five addresses.
Error e-mail is sent on the error
items checked in their check
boxes.
Send test e-mail. This allows
you to confirm that the settings
for e-mail transmission are
properly set.
notification e-mail is sent. You
can set up to five addresses.
Error e-mail is sent on the error
items checked in their check
boxes.
Send test e-mail. This allows
you to confirm that the settings
for e-mail transmission are
properly set.
Items
E-mail
Address
Address
Error Mail
(Lamp, Temp,
Fan)
Test
(Lamp, Temp,
Fan)
Test
Setting Error Items and
the URL that are to be
Displayed when an Error
Occurs
the URL that are to be
Displayed when an Error
Occurs
(Service & Support –
Access URL)
On this screen, you can make settings of the
URL and error items that are to be displayed
when the projector has generated an error.
URL and error items that are to be displayed
when the projector has generated an error.
Example of the display when an error occurs
Description
Set the URL that is to be
displayed when an error
occurs. You can set up to five
addresses.
The URL is displayed when an
error checked in their check
boxes occurs.
The set URL site is test-
displayed. This allows you to
confirm that the URL site is
properly displayed.
displayed when an error
occurs. You can set up to five
addresses.
The URL is displayed when an
error checked in their check
boxes occurs.
The set URL site is test-
displayed. This allows you to
confirm that the URL site is
properly displayed.
Items
Access
URL
URL
Condition
(Always, Lamp,
Temp, Fan)
Test
(Always, Lamp,
Temp, Fan)
Test
-18
Setting up the Projector Using RS-232C or Telnet
When Connecting Using
RS-232C
RS-232C
1
Launch general purpose terminal
emulator.
emulator.
2
Input settings for the RS-232C port
of the terminal emulator as follows.
of the terminal emulator as follows.
Baud Rate
: 9600 bps*
Data Length
: 8 bit
Parity Bit
: None
Stop Bit
: 1 bit
Flow Control : None
* This is the factory default setting. If the value
of Baud Rate for the projector has been
changed, set Baud Rate here according to
the changed value on the projector.
changed, set Baud Rate here according to
the changed value on the projector.
3
Input “PJS11234” and press the
“Enter” key.
“Enter” key.
4
“OK” is displayed. Input “PJS25678”
and press the “Enter” key within 10
seconds.
and press the “Enter” key within 10
seconds.
5
“User Name:” is displayed. Input the
user name and press the “Enter”
key.
user name and press the “Enter”
key.
• If a user name has not yet been set, just
press the “Enter” key.
6
“Password:” is displayed. Input the
password and press the “Enter” key.
password and press the “Enter” key.
• If a password has not yet been set, just press
the “Enter” key.
Connect the projector to a computer using RS-232C or Telnet, and open the SETUP MENU on
the computer to carry out various settings for the projector.
the computer to carry out various settings for the projector.
7
Input “setup” and press the “Enter”
key.
key.
• SETUP MENU will be displayed.
Note
• User name and password are not set in the fac-
tory default settings.
• If the user name or password is entered incor-
rectly three times, SETUP MENU will be quit.
▼SETUP MENU
---------------------------------SETUP MENU--------------------------------
[1]IP Address
[1]IP Address
[2]Subnet Mask
[3]Default Gateway
[4]User Name
[5]Password
[6]RS-232C Baud Rate [7]Projector Name [8]DHCP Client
[A]Advanced Setup
[A]Advanced Setup
[D]Disconnect All
[V]View All Setting
[S]Save & Quit
[Q]Quit Unchanged
setup>
-19
Setting up the Projector Using RS-232C or Telnet
When Connecting Using
Telnet
Telnet
1
Click “Start” from the Windows
®
desk-
top and select “Run”.
2
Enter “telnet 192.168.150.2” in the text
box that opens up. (If the IP address
of the projector is 192.168.150.2.)
box that opens up. (If the IP address
of the projector is 192.168.150.2.)
3
Click the “OK” button.
4
“User Name:” is displayed. Input the
user name and press the “Enter”
key.
user name and press the “Enter”
key.
• If a user name has not yet been set, just
press the “Enter” key.
5
“Password:” is displayed. Input the
password and press the “Enter” key.
password and press the “Enter” key.
• If a password has not yet been set, just press
the “Enter” key.
6
Input “setup” and press the “Enter”
key.
key.
• SETUP MENU will be displayed.
Note
• If the IP address has been changed, be sure to
enter the new IP address in step 2.
• User name and password are not set in the fac-
tory default settings.
• If the user name or password is entered incor-
rectly three times in steps 4 or 5, SETUP MENU
will be quit.
will be quit.
---------------------------------SETUP MENU--------------------------------
[1]IP Address
[1]IP Address
[2]Subnet Mask
[3]Default Gateway
[4]User Name
[5]Password
[6]RS-232C Baud Rate [7]Projector Name [8]DHCP Client
[A]Advanced Setup
[A]Advanced Setup
[D]Disconnect All
[V]View All Setting
[S]Save & Quit
[Q]Quit Unchanged
setup>
▼SETUP MENU
-20
Setting up the Projector Using RS-232C or Telnet
SETUP MENU
(Main Menu)
[1]IP Address
IP address settings. (Page
23
)
[2]Subnet Mask
Subnet mask settings. (Page
23
)
[3]Default Gateway
Default gateway settings. (Page
23
)
[4]User Name (Factory default setting : Not Re-
quired)
Setting of user name for security protection. (Page
Setting of user name for security protection. (Page
23
)
[5]Password (Factory default setting : Not Required)
Setting of password for security protection. (Page
24
)
[6]RS-232C Baud Rate (Factory default setting :
9600 bps)
Baud rate settings for the RS-232C terminals. (Page
Baud rate settings for the RS-232C terminals. (Page
24
)
[7]Projector Name (Factory default setting : XG-
MB67X)
It is possible to assign a projector name. (Page
It is possible to assign a projector name. (Page
24
)
[8]DHCP Client
DHCP Client settings. (Page
24
)
[A]Advanced Setup
Enters ADVANCED SETUP MENU. (Page
25
)
[D]Disconnect All
Disconnect all connections. (Page
25
)
[V] View All Setting
Displays all setting values. (Page
21
)
Can also be used with ADVANCED SETUP MENU.
[S] Save & Quit
Save set values and quit menu. (Page
22
)
[Q]Quit Unchanged
Quit menu without saving setting values. (Page
22
)
Note
• When “DHCP Client” is set to “OFF” on the
projector:
IP address : 192.168.150.2
Subnet mask : 255.255.255.0
Default gateway : 0.0.0.0
IP address : 192.168.150.2
Subnet mask : 255.255.255.0
Default gateway : 0.0.0.0
ADVANCED SETUP MENU
[1]Auto Logout Time (Factory default setting : 5 min-
utes)
Setting of time until automatic disconnection of net-
work connection. (Page
Setting of time until automatic disconnection of net-
work connection. (Page
25
)
[2]Data Port (Factory default setting : 10002)
Setting the TCP port number used when exchang-
ing data. (Page
ing data. (Page
25
)
[5]Network Ping Test
It is possible to confirm that a network connection
between the projector and a computer etc. is work-
ing normally. (Page
between the projector and a computer etc. is work-
ing normally. (Page
26
)
[6]Accept IP Addr(1)
[7]Accept IP Addr(2)
[8]Accept IP Addr(3)
[9]Accept All IP Addr (Factory default setting : Ac-
[7]Accept IP Addr(2)
[8]Accept IP Addr(3)
[9]Accept All IP Addr (Factory default setting : Ac-
cept All)
For improved security, it is possible to set up to three
IP addresses allowing connection to the projector.
Set IP addresses can be cancelled using [9] Accept
All IP Addr. (Page
For improved security, it is possible to set up to three
IP addresses allowing connection to the projector.
Set IP addresses can be cancelled using [9] Accept
All IP Addr. (Page
26
)
[0] Search Port (Factory default setting : 5006)
Setting the port number used when searching for
the projector. (Page
the projector. (Page
27
)
[!] Restore Default Setting
Restores all setting values that can be set using the
menu to the default state. (Page
menu to the default state. (Page
27
)
[Q]Return to Main Menu
Return to the main SETUP MENU. (Page
27
)
▼SETUP MENU
▼ADVANCED SETUP MENU
---------------------------------SETUP MENU--------------------------------
[1]IP Address
[1]IP Address
[2]Subnet Mask
[3]Default Gateway
[4]User Name
[5]Password
[6]RS-232C Baud Rate [7]Projector Name [8]DHCP Client
[A]Advanced Setup
[A]Advanced Setup
[D]Disconnect All
[V]View All Setting
[S]Save & Quit
[Q]Quit Unchanged
setup>
******************** ADVANCED SETUP MENU ***********************
[1]Auto Logout Time
[1]Auto Logout Time
[2]Data Port
[5]Network Ping Test
[6]Accept IP Addr(1)
[6]Accept IP Addr(1)
[7]Accept IP Addr(2)
[8]Accept IP Addr(3)
[9]Accept All IP Addr
[0]Search Port
[!]Restore Default Setting
[Q]Return to Main Menu
[Q]Return to Main Menu
advanced>
Click on the first or last page to see other XG-MB67X (serv.man17) service manuals if exist.