Sharp XG-MB67X (serv.man17) User Manual / Operation Manual ▷ View online
-13
Controlling the Projector via LAN
Controlling the Projector
Using Internet Explorer
Using Internet Explorer
(Version 5.0 or later)
Complete connections to external equipment
before starting the operation. (See pages 21-
27 of the projector’s operation manual.)
Complete the AC cord connection. (See page
27 of the projector’s operation manual.)
before starting the operation. (See pages 21-
27 of the projector’s operation manual.)
Complete the AC cord connection. (See page
27 of the projector’s operation manual.)
Note
• When connecting the projector to the LAN, use
a LAN cable (Category 5). When connecting the
projector to a hub, use a straight-through cable.
projector to a hub, use a straight-through cable.
1
Start Internet Explorer (version 5.0
or later) on the computer.
or later) on the computer.
2
Enter “http://” followed by the
projector IP address set by the
procedure on page
projector IP address set by the
procedure on page
12
followed
by “/” in “Address”, and then
press the “Enter” key.
press the “Enter” key.
• When “DHCP Client” is set to “OFF” on
the projector, IP address is
192.168.150.2. If you did not change the
IP address in “3. Setting up a Network
Connection for the Projector” (pages
192.168.150.2. If you did not change the
IP address in “3. Setting up a Network
Connection for the Projector” (pages
11-12
), enter “http://192.168.150.2/”.
3
A screen for controlling the pro-
jector appears, ready for per-
forming various status condi-
tions, control, and settings.
jector appears, ready for per-
forming various status condi-
tions, control, and settings.
After connecting the projector to your network, enter the projector IP address in “Address”
on Internet Explorer (version 5.0 or later) using a computer on the network to start a setup
screen that will enable control of the projector via the network.
on Internet Explorer (version 5.0 or later) using a computer on the network to start a setup
screen that will enable control of the projector via the network.
-14
Confirming the Projector
Status
Status
(Status)
On this screen, you can confirm the projector
status. You can confirm the following items :
status. You can confirm the following items :
•••••
MAC Address
•••••
Power
•••••
Condition
•••••
Lamp Timer
•••••
Lamp Life
•••••
Input
•••••
Signal Info
•••••
Serial Number
Note
• If you click the “Refresh” button before the
screen is displayed completely, an error
message (“Server Busy Error”) will be dis-
played. Wait for a moment and then oper-
ate again.
message (“Server Busy Error”) will be dis-
played. Wait for a moment and then oper-
ate again.
• For details about each item, refer to the
projector’s operation manual.
Controlling the Projector via LAN
Controlling the Projector
(Control)
On this screen, you can perform projector
control. You can control the following items :
control. You can control the following items :
•••••
Power
•••••
Input Select
•••••
Volume
•••••
AV Mute [OFF] [ON]
Note
• If you click the “Refresh” button before the
screen is displayed completely, an error mes-
sage (“Server Busy Error”) will be displayed.
Wait for a moment and then operate again.
sage (“Server Busy Error”) will be displayed.
Wait for a moment and then operate again.
• You cannot operate this page while the pro-
jector is warming up.
• While the projector is in standby mode, you
can only control “Power ON”.
• For details about each item, refer to the
projector’s operation manual.
-15
Controlling the Projector via LAN
Setting and Adjusting the
Projector
Projector
(Settings & Adjustments)
Example: “Picture” screen display for INPUT 1
On these screens, you can make projector
settings or adjustments. You can set or adjust
the following items :
settings or adjustments. You can set or adjust
the following items :
•••••
Picture Mode
•••••
CLR Temp
•••••
Bright Boost
•••••
Progressive (INPUT 3/4)
•••••
Lamp Setting
•••••
Resolution Setting
•••••
Signal Type (INPUT 1/2)
•••••
Video System (INPUT 3/4)
•••••
Resize
•••••
Auto Keystone [OFF][ON]
•••••
OSD Display [OFF][ON]
•••••
Background
•••••
Setup Guide [OFF][ON]
•••••
Projection Mode
•••••
OSD Language
•••••
Auto Search [OFF][ON]
•••••
Auto Sync [OFF][ON]
•••••
Auto Power Off [OFF][ON]
•••••
System Sound [OFF][ON]
•••••
Internal Speaker [OFF][ON]
•••••
RS-232C Speed
•••••
Fan Mode [Normal] [High]
•••••
All Reset
Note
• If you click the “Refresh” button before the
screen is displayed completely, an error mes-
sage (“Server Busy Error”) will be displayed.
Wait for a moment and then operate again.
sage (“Server Busy Error”) will be displayed.
Wait for a moment and then operate again.
• You cannot operate this page while the pro-
jector is warming up.
• For details about each item, refer to the
projector’s operation manual.
Setting the Security
(Network – Security)
On this screen, you can make settings relat-
ing to security.
ing to security.
Note
• User Name and Password can be up to 8
characters.
• You can input the characters below :
a-z, A-Z, 0-9, -, _
Description
Setting of user name for
security protection.
Setting of password for
security protection.
It is possible to set up to three
IP addresses allowing connec-
tion to the projector.
No limits are set to IP addresses
connecting to the projector.
For security improvement, only an
IP address set by “Address 1-3”
can be connected to the projector.
security protection.
Setting of password for
security protection.
It is possible to set up to three
IP addresses allowing connec-
tion to the projector.
No limits are set to IP addresses
connecting to the projector.
For security improvement, only an
IP address set by “Address 1-3”
can be connected to the projector.
Items
User Name
Password
Accept IP
Address
Address
All IP
Addresses
From only
specific IP
addresses
Addresses
From only
specific IP
addresses
-16
Controlling the Projector via LAN
Making General Settings
for the Network
for the Network
(Network -
General)
On this screen, you can make general settings
relating to the network.
relating to the network.
After clicking the “Apply” button, the set val-
ues appear. Confirm that the values are set
properly, and then click the “Confirm” but-
ton.
ues appear. Confirm that the values are set
properly, and then click the “Confirm” but-
ton.
Note
• After setting items, wait for 10 seconds and
then re-access.
• Projector Name can be up to 12 characters.
• You can input the characters below :
• You can input the characters below :
A-Z, 0-9, -, _, (,), space
(When “a-z” are input, they are converted to
“A-Z” automatically.)
(When “a-z” are input, they are converted to
“A-Z” automatically.)
Description
Setting the projector name.
Setting the time interval in
which the projector will be
automatically disconnected
from the network in units of a
minute (from 1 to 65535
minutes). If the set value is
made 0, the Auto Logout
function is disabled.
Setting the TCP port number
used when exchanging data
with the projector (from 1025 to
65535).
Setting the port number used
when searching for the
projector (from 1025 to 65535).
which the projector will be
automatically disconnected
from the network in units of a
minute (from 1 to 65535
minutes). If the set value is
made 0, the Auto Logout
function is disabled.
Setting the TCP port number
used when exchanging data
with the projector (from 1025 to
65535).
Setting the port number used
when searching for the
projector (from 1025 to 65535).
Items
Projector
Name
Auto
Logout
Time
Name
Auto
Logout
Time
Data Port
Search
Port
Port
Setting example / Remarks
Setting an SMTP server
address for e-mail transmis-
sion.
e.g.1 : 192.168.150.253
e.g.2 : smtp123.sharp.co.jp
* When using a domain name,
address for e-mail transmis-
sion.
e.g.1 : 192.168.150.253
e.g.2 : smtp123.sharp.co.jp
* When using a domain name,
make settings for the DNS
server.
server.
Setting the projector’s e-mail
address. The e-mail address set
here becomes Originator E-mail
Address.
Setting the sender’s name.
The name set here appears in
the “Originator Name” column
of the body of the message.
address. The e-mail address set
here becomes Originator E-mail
Address.
Setting the sender’s name.
The name set here appears in
the “Originator Name” column
of the body of the message.
Items
SMTP
Server
Server
Originator
E-mail
Address
Address
Originator
Name
Name
Setting for Sending E-mail
when an Error Occurs
when an Error Occurs
(Mail – Originator Settings)
On this screen, you can make settings for
sending e-mail to report when the projector
has generated an error.
sending e-mail to report when the projector
has generated an error.
Note
• SMTP Server, Originator E-mail Address and
Originator Name can be up to 64 characters.
• You can input the characters below:
SMTP Server and Originator E-mail Address :
a-z, A-Z, 0-9, !, #, $, %, &, *, +, -, /, =, ?, ^, {,
|, }, ~, _, ’, ., @, `
(You can input “@” only one time for “Origi-
nator E-mail Address”.)
Originator Name : a-z, A-Z, 0-9, -, _, (,), space
a-z, A-Z, 0-9, !, #, $, %, &, *, +, -, /, =, ?, ^, {,
|, }, ~, _, ’, ., @, `
(You can input “@” only one time for “Origi-
nator E-mail Address”.)
Originator Name : a-z, A-Z, 0-9, -, _, (,), space
• If the settings of “3. Setting up a Network
Connection for the Projector” on pages
11
and
12
are incorrectly set, e-mail will not be
send.
Click on the first or last page to see other XG-MB67X (serv.man17) service manuals if exist.